Search NASA⌕ Search

Engineering topics

Kowalski, Benjamin

Publications and source records attributed to Kowalski, Benjamin.

Creating High Temperature Ferroelectrics by Using Ternary Components with Limited Solubility

High temperature ferroelectrics are needed for actuator applications ranging from drilling on the surface of Venus to fuel modulation in jet engines. Machine learning in previous work has dramatically reduced search space and produced new candidates for experimentation. It is possible to create high temperature piezoelectrics by changing the end member of ternary systems. The starting point was near the morphotropic phas boundary between BiScO3(BS) and PbTiO3 (PT) (38%/62%). The third end member was suggested by machine learning to create a high Tc with limited solubility; BiCo0.88Fe0.12O3 (BCF).

Hirt, Benjamin↗

Thermochemistry of Protective Coatings and Molten Silicate Debris

The durability of gas-turbine engine components can be significantly affected by the ingestion of siliceous particles, which can melt at high temperature and corrode protective coatings that are essential for long life requirements. The silicate debris consists mainly of CaO-MgO-Al2O3-SiO2 (CMAS) and is usually ingested by aircraft engines during and after take-off, sticking to their hot surfaces and resulting in the formation of calcium rare-earth silicate oxyapatites. The thermochemistry of coatings and their reaction products with molten silicate debris are crucial to understand in order to improve the durability of gas-turbine engines. Here we discuss results of high temperature drop solution calorimetry, drop-and-catch calorimetry (DnC) and differential thermal analysis (DTA) techniques for the thermodynamic properties of both thermal barrier coatings (TBCs) and environmental barrier coatings (EBCs) and their reaction with CMAS compositions. The enthalpies of solution of Y2Si2O7, Yb2Si2O7, 31YSZ, and 16RESZ based coatings and the oxyapatite are moderately positive. However, oxyapatite formation is only favorable over coating dissolution in terms of enthalpy for 7YSZ. The enthalpies of mixing between the coatings and the molten silicate are less exothermic for Yb2Si2O7 and CaYb4Si3O13 than for 7YSZ, indicating lower energetic stability of the latter against molten silicate corrosion. We also report for the first time the calorimetric measurements of the enthalpies of formation of rare-earth silicate based EBC coatings and oxyapatites (rare-earth, RE = Y, Yb, Gd, Dy, Er, Nd and Sm).

Costa, Gustavo↗

Compositional and Microstructural Effects in the Protection of SiC Components in Water Vapor

Greater gas turbine engine efficiency is a major goal in aeronautics research often pursued through increased engine operating temperatures. However, it is necessary to replace the current hot-stage alloy components with more thermally robust parts, such as promising Silicon-based ceramics and composites. Unfortunately, these materials are still susceptible to the effects of oxidation, water vapor, and (Calcium-Magnesium-Alumino-Silicate) CMAS interaction, among other issues at high temperature. To mitigate these effects, environmental barrier coating (EBC) materials are employed to help control the rate of degradation to the underlying composite. Often, a thermally grown oxide (TGO) layer forms between the EBC and the composite which can act as a point of failure. The current study focuses on the combined effects of water vapor, composite composition, and microstructure in TGO formation on protected and unprotected SiC samples which have been produced under different processing conditions.

Kowalski, Benjamin↗

Experimental search for high-temperature ferroelectric perovskites guided by two-step machine learning

Experimental search for high-temperature ferroelectric perovskites is a challenging task due to the vast chemical space and lack of predictive guidelines. Here, we demonstrate a two-step machine learning approach to guide experiments in search of xBi½Me0 yMe00 ð1yÞO3–(1 - x) PbTiO3-based perovskites with high ferroelectric Curie temperature. These involve classification learning to screen for compositions in the perovskite structures, and regression coupled to active learning to identify promising perovskites for synthesis and feedback. The problem is challenging because the search space is vast, spanning ~61,500 compositions and only 167 are experimentally studied. Furthermore, not every composition can be synthesized in the perovskite phase. In this work, we predict x, y, Me', and Me" such that the resulting compositions have both high Curie temperature and form in the perovskite structure. Outcomes from both successful and failed experiments then iteratively refine the machine learning models via an active learning loop. Our approach finds six perovskites out of ten compositions synthesized, including three previously unexplored {Me'Me"} pairs, with 0.2Bi (Fe0.12Co0.88)O3–0.8PbTiO3 showing the highest measured Curie temperature of 898 K among them.

36 MATERIALS SCIENCE↗

Water Vapor Corrosion in EBC Constituent Materials

Environmental Barrier Coating (EBC) materials are sought after to protect ceramic matrix composites (CMC) in high temperature turbine engines. CMCs are particularly susceptible to degradation from oxidation, Ca-Al-Mg-Silicate (CMAS), and water vapor during high temperature operation which necessitates the use of EBCs. However, the work presented here focuses on water vapor induced recession in EBC constituent materials. For example, in the presence of water vapor, silica will react to form Si(OH)4 (g) which will eventually corrode the material away. To investigate the recession rate in EBC constituent materials under high temperature water vapor conditions, thermal gravimetric analysis (TGA) is employed. The degradation process can then be modeled through a simple boundary layer expression. Ultimately, comparisons are made between various single- and poly-crystalline materials (e.g. TiO2, SiO2) against those found in literature.

coating↗

High Temperature Ferroelectrics for Actuators: Recent Developments and Challenges

A variety of piezoelectric applications have been driving the research in development of new high temperature ferroelectrics; ranging from broader markets such as fuel and gas modulation and deep well oil drilling to very specific applications such as thermoacoustic engines and ultrasonic drilling on the surface of Venus. The focus has been mostly on increasing the Curie temperature. However, greater challenges for high temperature ferroelectrics limit the operating temperature to levels much below the Curie temperature. These include enhanced loss tangent and dc conductivity at high fields as well as depoling due to thermally activated domain rotation. The initial work by Eitel et al. [Jpn. J. Appl. Phys., 40 [10, Part 1] 59996002 (2001)] increased interest in investigation of Bismuth containing perovskites in solid solution with lead titanate. Issues that arise vary from solubility limits to increased tetragonality; the former one prohibits processing of morphotropic phase boundary, while the latter one impedes thorough poling of the polycrystalline ceramics. This talk will summarize recent advances in development of high temperature piezoelectrics and provide information about challenges encountered as well as the approaches taken to improve the high temperature behavior of ferroelectrics with a focus on applications that employ the converse piezoelectric effect.

Piezoelectric↗

Effects of Dopant on Depoling Temperature in Modified BiScO3 - PbTiO3

In recent years there has been a renewed interest for high temperature piezoelectrics for both terrestrial and aerospace applications. These applications are limited in part by the operating temperature, which is usually taken as one half of the Curie temperature (Tc), and is 200C for one of the most widely used commercial piezoelectrics, Pb(Zr,Ti)O3 (PZT). In an effort to increase Tc, subsequent research into high temperature Bi(BB)O3 PbTiO3 piezoelectrics led to the discovery of the morphotropic phase boundary (MPB) in the high-Tc BiScO3 PbTiO3 (BS-PT) system with a Tc of 460C and a d33 of 460 pmV. The Tc marks the ferroelectric to paraelectric phase transformation and while, in general, a phase transformation leads to thermal depoling in piezoelectrics with low or moderate Tcs, for high Tc piezoelectrics thermally assisted dipole rotation can lead to randomization of domains at temperatures below Tc. It becomes necessary to determine the depoling temperature (Td) which dictates the actual working temperature range. By doping for Sc and Ti the Td can be shifted while maintaining similar electromechanical properties as a function of temperature. The effect of this B-site doping on depoling temperature has been explored through the characterization of microstructure and weakhigh field measurements.

Actuator↗

Structure and properties of Fe-modified Na[subscript 0.5]Bi[subscript 0.5]TiO[subscript 3] at ambient and elevated temperature

Sodium bismuth titanate (NBT) ceramics are among the most promising lead-free materials for piezoelectric applications. This work reports the crystal structure and phase evolution of NBT and Fe-modified NBT (from 0-2 at.% Fe) using synchrotron x-ray diffraction and Raman spectroscopy, at both ambient and elevated temperatures. The crystallographic results are discussed with reference to permittivity and piezoelectric thermal depolarization measurements of the same compositions. Changes in the depolarization temperature due to Fe substitution were detected by Raman spectroscopy and were found to correlate closely with depolarization temperatures obtained from converse piezoelectric coefficient and permittivity measured in situ. The depolarization temperatures obtained from direct piezoelectric coefficient measured ex situ as well as the phase transition temperatures obtained from synchrotron x-ray diffraction were found to be at higher temperatures. The mechanisms underlying the relationship between permittivity and piezoelectric depolarization to structural transitions observed in Raman spectroscopy and x-ray diffraction are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Phase transition sequence in sodium bismuth titanate observed using high-resolution x-ray diffraction

High resolution powder x-ray diffraction patterns of Na{sub 0.5}Bi{sub 0.5}TiO{sub 3} at selected temperatures were examined to compare structural changes with observed piezoelectric thermal depoling temperatures. The depoling temperatures do not correlate with discrete phase transition temperatures, and therefore, a structural transition is not the origin of thermal depoling. Rather, a correlation is made with an increase in volume fraction of material which does not obey the long-range Cc space group. The origin of the thermal depoling behavior may be the loss of long-range ferroelectric order by a decreasing proportion of the Cc phase or the associated percolation of disordered nano-scale platelets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗