Analysis of nuclear microreactor efficacy with hydrogen production methods
Not provided.
Engineering topics
Publications and source records attributed to Kozlowski, Tomasz.
Not provided.
Not provided.
Tri-structural isotropic (TRISO) fuel particles are a fuel form being considered for potential use in next-generation nuclear reactors (i.e., high-temperature gas-cooled reactors). Though the TRISO fuel manufacturing process has continually advanced in recent years, particle comparisons still reveal statistical variations and uncertainties in terms of geometric configurations and material properties. Given that the physical processes ongoing in TRISO fuel particles during reactor operation are highly correlated with each other, a small degree of uncertainty in one model may lead to significant uncertainty in another. This makes appropriate uncertainty quantification of TRISO fuel particles essential. However, one may wonder about the extent to which the current version of TRISO particles has been optimized, and whether any room remains for further improvements. This paper quantifies TRISO fuel performance model uncertainties that stem from geometric and material data. For this analysis, the BISON code was used, and the Advanced Gas Reactor (AGR)-2 experiment served as a reference case. A total of 10 5 calculations was performed for the uncertainty and optimization analysis, altering the geometric and material data within their uncertainty range. Lastly, the optimization potential of TRISO particles is evaluated from a fuel performance perspective.
Not provided.
This project is dedicated towards designing a fuel processing system that enables liquid-fueled molten salt reactors (MSR) to load follow by removing the dissolved xenon in the fuel salt. As one of the Gen-IV nuclear reactor concepts, the molten salt reactor receives increasing development interests in the recent years. One distinguishing feature of the liquid-fueled molten salt reactor is its improved ability to operate in a load-following mode by including the unique online fission product removal system. Load-following means that the reactor changes its power output based on the demand on the grid. Most of the current operating nuclear reactors have limited load-following ability and operate as the base load on the grid. Due to the rapid increase of solar energy, the requirement on load-following capacity is significantly increased because of the varying power output of the solar panels, yet the traditional load-following capacity is expected to decrease as the decarbonization of the grid continues. Therefore, the ability to perform load-following operation for the nuclear reactors will greatly enhance the resilience of the grid and make nuclear energy more economically competitive. This load-following feature is included in many commercial molten salt reactor designs, such as the designs by Transatomic Power, Terrestrial Energy, and Flibe Energy. Unfortunately, detailed analysis of the fuel processing system for commercial scale MSRs is still lacking, as well as how the fuel processing quantitively impacts the load-following operation. Moreover, experimental data for many of the underlying physics of fuel processing is limited. This project aims to pave the way for the fuel processing technology to advance to the commercial stage by performing combined experimental and simulation research. During the project period, four interconnected aspects of the development of the fuel processing system in liquid-fueled molten salt reactors are investigated. These aspects are the simulation and analysis of the fission product removal system, the fuel cycle simulation, the coupled reactor neutronics and thermal hydraulics transient simulation, and the gaseous fission product removal experiment. Multiphase CFD simulations are performed for components of the processing systems, and simplified air-water experiments are carried out to provide validation data. It is concluded that the CFD simulation can satisfactorily predict the system level performance of the components, and engineering models are constructed based on this success. Fuel cycle analysis is performed for two representative MSR design, the MSBR and the Transatomic Power MSR. Open-source code SaltProc is developed to incorporate the unique fuel processing system of the MSRs. It is concluded that the removal of xenon is essential for load-following operation in thermal spectrum MSR and Molten Salt Breeder Reactor. For the Transatomic Power MSR, the xenon poisoning effect is negligible due to its relatively fast neutron spectrum, though the overall fuel cycle economics still benefits from the removal of xenon. Coupled reactor neutronics and thermal hydraulics transient simulation is performed specifically for the Transatomic Power MSR. It is concluded that the reactor core design could perform power ramping fast enough to satisfy load-following operation. Combining the findings from each aspect, it is concluded that the load-following operation of a thermal neutron MSR is dependent upon the removal of xenon, which could be achieved for a commercial sized reactor using continuous inert gas sparging in a separate system with reasonable dimensions.
The goal of this study is to analyze the effect of radial void fraction distribution, considered at three degrees of fidelity, on lattice and 2-group homogenized cross sections. The novelty of this work lies in its use of experimentally-determined radial void fraction distributions which allows for fine-scale coolant density data with no predictive uncertainty and which could be prohibitively expensive to simulate over the range of operational parameters used in the experiments. The experimentally-determined radial void fraction distributions are also characterized using a statistical tool called a semi-variogram in order to determine the scale of continuity. Void fraction distributions are averaged at the lattice and subchannel level for comparison with the fine-scale model. Models averaged at the subchannel and lattice level show a difference in about 68% of the time. Also, by comparing 2-group homogenized cross-sections, the differences between the subchannel and homogeneous cases are measurable.
During the last few years, deep learning in neural networks has demonstrated impressive successes in the areas of computer vision, speech and image recognition, text generation, and many others. However, sensitive engineering areas such as nuclear engineering benefited less from these efficient techniques. In this work, deep learning expert systems are utilized to model and predict time series progression of a design-basis nuclear accident, featuring a loss of coolant accident. Two major findings are accomplished in this work. First, the ability to train expert systems with high accuracy, which could help nuclear power plant operators to figure out plant responses during the accident. Second, building fast, efficient, and accurate deep models to simulate nuclear phenomena, which could be valuable to nuclear computational science. In this work, large amount of time series data is obtained from simulation tools by simulating different conditions of the base-case/nominal accident scenario. Four critical outputs/responses are monitored during the accident (e.g. temperature, pressure, break flow rate, water level). Two approaches are adopted in this work. The first approach is to use feedforward deep neural networks (DNN) to fit all time steps and outputs in a single model. The second approach is to use long short-term memory (LSTM) to fit all time steps together for each reactor response separately. Both DNN and LSTM demonstrate very good performance in predicting the test and base-case scenarios, with accuracy as low as 92% and as high as 99%, where these test scenarios are unknown to the expert systems and are not included in the model training. In addition, both approaches demonstrate a significant reduction in computational costs, as the deep expert system is able to accurately predict the accident 100,000 times faster than the original simulation tool. Given sufficient data, the methodology adopted in this study demonstrates that DNN/LSTM expert systems can be used as a decision support system to model advanced time series phenomena within nuclear power plants with high accuracy and negligible computational costs.
Not Available
Not provided.
Not provided.
New reactor designs such as small modular reactors and newly proposed passive safety systems rely on natural circulation two-phase flow cooling of the reactor core under accident conditions. Without a pump to drive the flow, the circulation rate is a strong function of void fraction. Under these conditions where the flow rate, pressure drop, and heat transfer are all closely coupled through the mixture density, the accurate prediction of void fraction is pivotal. Furthermore, while these passive systems boast a more reliable cooling option, the sensitivity of the system to two-phase flow instabilities is more likely than in forced convective cooling and can result in dangerous density wave or flow excursion conditions. Improvement of one-dimensional system codes and further development of three-dimensional code capability are all important efforts in addressing these issues. The proposed work is a critical step towards providing confidence through validation of the capability of thermal-hydraulic tools to meet the emerging challenges in reactor simulation. Historically, system analysis codes develop a stiffness over time due to fine-tuning of adjustable code parameters that result in a reluctance or inability to adopt improved models. Therefore, a rigorous effort should be invested in preparation for RELAP-7 to identify required modeling improvements of constitutive relations and validation of the code applicability to the wide range of possible reactor flow conditions. Part of this validation involves the uncertainty quantification which is a critical step in the Code Scaling, Applicability, and Uncertainty (CSAU) methodology and Best-Estimate Plus Uncertainty (BEPU) licensing method. BEPU allows recovery of safety margins and potentially optimizing plant performance, resulting in economic benefit for the reactor operators. Beginning with the collection of past experimental data covering prototypic LWR conditions, this document reviews three critical datasets available for the validation of system codes. The experimental methods, procedures, facilities, instrumentation, and supplementary information are consolidated to aid the validation efforts of this work and future projects. These three datasets (824 conditions) are chosen due to their wide acceptance and demonstrated application for code validation. Two experimental datasets from the Nuclear Power Engineering Corporation (NUPEC) span prototypic conditions of Boiling Water Reactors (BWR) and Pressurized Water Reactors (PWR). These datasets are labeled as the BFBT (BWR Full-size Fine-mesh Bundle Test) and the PSBT (PWR Subchannel and Bundle Test) datasets respectively. The third dataset is taken in an internally heated annulus that is scaled based on a BWR subassembly and includes two-phase flows important to post-blowdown analysis. Together, the datasets consider the full range of pressure and mass flux expected in LWR forced convective flows from steady-state to long term cooling conditions. Recognizing the deficiency of available data under low-pressure, low-flow, a new natural circulation dataset consisting of 107 conditions is obtained. With system pressures ranging between 145 and 950 kPa, natural circulation is driven by a heat flux up to 275 kW/m2 in a 3 m long heated region of the annulus test section which is followed by a 2 m long unheated region before entering a condenser. Stable natural circulation flow rates in this facility were measured to be between 182 and 590 kg/m2-s. Pressure and temperature are measured at ten locations in the facility. In addition, measurements of void fraction, interfacial area concentration, and gas velocity are obtained at five axial locations in the annulus test section. The RELAP5-3D code demonstrates good accuracy for void fraction predictions in BFBT and PSBT benchmarks, but shows relatively large discrepancy in the annulus experiments at lower pressures. In two-phase natural circulation, large oscillations are observed in many system parameters during the simulation of 19 experiment cases which were conducted at low pressures, and the model shows good predictive performance with the remaining 88 experiment cases. However, some discrepancies in void fraction and temperature predictions are found which may require improved constitutive modeling under these low-pressure, low-flow condition. The quantified uncertainty in void fraction predictions in three forced convection benchmarks due to uncertainties in boundary conditions and geometries are relatively small, except for a few cases in the annulus experiment. The output uncertainty of the natural circulation model is quantified by considering the measurement error in boundary conditions, and it is shown that the output uncertainty ranges are relatively small for the range of conditions considered. Through this work, a clear pathway is provided for validation of RELAP7 once the code is available.
A novel and modern framework for energy modeling is developed in this paper with a focus on nuclear energy modeling and simulation. The framework combines multiphysics simulations and real data, with validation by uncertainty quantification tasks and facilitation by machine and deep learning methods. The hybrid framework is built on the basis of a wide range of physical models, real data, mathematical and statistical methods, and artificial intelligence techniques. The framework is demonstrated in different applications, including quantifying uncertainties in computer simulations, multiphysics coupling, analysis of variance using machine learning surrogate models, deep learning of time series phenomena, and propagating parametric uncertainties of nuclear data. The applications demonstrated are oriented to nuclear engineering simulations, even though majority of the methods are applicable to other energy sources (eg, renewable). Efficient utilization of this framework is expected to yield a much better understanding of the physical phenomena analyzed as well as an improvement in the performance of the energy design/model under construction.
A new data-driven sampling-based framework was developed for uncertainty quantification (UQ) of the homogenized kinetic parameters calculated by lattice physics codes such as TRITON and Polaris. In this study, extension of the database for the delayed neutron data (DND) is performed by exploring more delayed neutron experiments and adding additional isotopes/actinides to the data libraries. Afterwards, the framework is utilized to obtain a deeper knowledge of the kinetic parameters’ sensitivity and uncertainty. The kinetic parameters include precursor-group-wise delayed neutron fraction (DNF) and decay constant. Input uncertainties include nuclear data (i.e., cross-sections) and DND (i.e., precursor group parameters and fractional delayed neutron yield). It is found that kinetic parameters, especially DNFs, have large uncertainties. The DNF uncertainty is driven by the cross-section uncertainties for LWR designs, while decay constant uncertainty is dominated by the DND uncertainties. The usage of correlated U-235 thermal DND in the UQ process significantly reduces the DND uncertainty contribution on the kinetic parameters. Large void fraction and presence of neutron absorber (e.g., control rod) increase the DNF uncertainty due to the hardening of neutron spectrum. High correlation between the DNF groups ( β 1 , . . , β 6 ) is observed, while the decay constant groups ( λ 1 , . . , λ 6 ) show weak correlation to each other and also to DNF groups. The DNF uncertainties of the dominant precursor group 4 for PWR, BWR, and VVER are about 7.5%, 9.4%, and 7.6%, respectively. The DNF uncertainty grows to larger values after fuel burnup. Kinetic parameters’ values and uncertainties provided here can be efficiently used in subsequent core calculations, point reactor kinetics, and other applications.
Not provided.
Verification, validation and uncertainty quantification (VVUQ) have become a common practice in thermal-hydraulics analysis. In general, these activities deal with propagations of uncertainties in computer code simulations, e.g., through system analysis codes. However, most existing such activities in thermal-hydraulics analysis have been primarily focused on input and model uncertainties, while numerical errors were largely overlooked. Numerical errors can appear in many different forms, e.g., round-off error, statistical sampling error, and discretization error. In thermal-hydraulics analysis, especially two-phase flow simulations commonly encountered in reactor safety analysis, the lack of consideration of discretization error is mainly due to the difficulty in estimating them. Accurate estimations of discretization error require continuous mesh refinement and/or implementation of high-order numerical schemes in system analysis code, both of which are difficult to achieve in existing codes. In this work, we will build a computer code that incorporates both first-order and second-order numerical methods to solve the two-phase flow problems. The first-order method resembles the one used in many existing system analysis codes; and the second-order method works as the reference to estimate numerical errors. Numerical verification of spatial discretization schemes will be presented in the form of mesh convergence study. It will also be demonstrated via case studies that, in practical scenarios, discretization errors can be as large as, or even larger than, model uncertainties.
Not Available
The DOE NEUP sponsored IRP on accident tolerant fuel (ATF) entitled Engineered Zircaloy Cladding Modifications for Improved Accident Tolerance of LWR Nuclear Fuel involved three academic institutions, Idaho National Laboratory (INL), and ATI Materials (ATI). Detailed descriptions of the work at the University of Illinois (UIUC, prime), the University of Florida (UF), the University of Michigan (UMich), and INL are included in this document as separate sections. This summary provides a synopsis of the work performed across the IRP team. Two ATF solution pathways were initially proposed, coatings on monolithic Zr-based LWR cladding material and selfhealing modifications of Zr-based alloys. The coating pathway was extensively investigated, both experimentally and in computations. Experimental activities related to ATF coatings were centered at UIUC, UF, and UMich and involved coating development and testing, and ion irradiation. Neutronic and thermal hydraulic aspects of ATF coatings were the focus of computational work at UIUC and UMich, while materials science aspects were the focus of computational work at UF and INL. ATI provided monolithic Zircaloy 2 and 4 material and a binary Zr-Y alloy material. The selfhealing pathway was investigated with advanced computations only. Beryllium was identified as a valid self-healing additive early in this work. However, all attempts to fabricate a Zr-Be alloy failed. Several avenues of fabrication were explored. ATI ultimately declined our fabrication request over health concerns associated with Be (we note that Be was not part of the original work scope and the ATI SOW). Likewise, Ames Laboratory declined our fabrication request, citing known litigation dating to the 1980s and 1990s involving the U.S. Federal government and U.S. National Laboratory employees involving the use of Be. Materion (formerly, Brush Wellman) also declined our fabrication request, citing the difficulty in working with a highly reactive Zr and Be. International fabrication options were explored in Europe and Asia, but this proved to be impractical, if not impossible. Consequently, experimental investigation of the Zr-Be binary system was dropped and exploration binary Zr-Y binary system was initiated. The motivation behind the Zr-Y system is the known thermodynamic stability of yttria over zirconia.
Nuclear reactor fuel performance analysis studies the thermo-mechanical behavior of fuel rods and verify their compliance with safety criteria under both normal operation and accidental conditions. One of the major concerns in fuel performance analysis is the behavior of the fission gases xenon and krypton in uranium dioxide fuel, which significantly affect the thermo-mechanical performance of the nuclear fuel rods employed in current LWRs. Previously, the modeling of fission gas release (FGR) in nuclear fuel performance codes have been relying on empirical models which are not applicable beyond their range of calibration. Recently a more efficient and flexible physics-based FGR and swelling model that can describe a wider range of reactor operation conditions have been implemented in fuel performance code BISON. In this work, we performed Bayesian calibration to inversely quantify the uncertainties associated with the 5 tuning parameters in BISON FGR model, based on the time-dependent FGR measurement data from Riso-AN3 benchmark. It takes around 1 hour and 40 minutes for BISON to simulate the Riso-AN3 benchmark with a moderate mesh size using 32 processors. As hundreds of thousands of BISON simulations are needed during Markov Chain Monte Carlo (MCMC) sampling, running BISON directly is not a viable solution. Therefore we propose to use Kriging-based metamodels to replace BISON during MCMC sampling. Surrogate model is an approximation of the input/output relation of a computer code/model. It is also called metamodel, response surface, emulator. Surrogate models usually take much less computational time than the original model (like BISON) while maintaining the input/output relation of the original model to a desirable accuracy. Constructing the metamodels normally requires small number of executions of the original model. Once validated, metamodels can be used to perform uncertainty and sensitivity analysis, Bayesian calibration, optimization, etc.