Synthesis of Nd-lean (Nd,Ce,La)-Fe-B magnets via hot deformation and rolling
Not Available
Anand, K. S.↗
Engineering topics
Kramer, M. J.
Publications and source records attributed to Kramer, M. J..
Orientation dependence of the effect of short-range ordering on the plastic deformation of a medium entropy alloy
Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? Here, to answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.
36 MATERIALS SCIENCE↗
High throughput exploration of the oxidation landscape in high entropy alloys
We report high entropy alloys (HEAs) have gained interest for structural applications in extreme environments. With a potentially vast chemical and phase space, there are significant opportunities to discover superior performing alloys. Crucial for most high-temperature applications is understanding and mitigating the oxidation behavior of these chemically complex alloys. Most experimental and computational HEA studies have focused on a limited set of compositions and only a fraction these compositions have been characterized for oxidation. We present a high-throughput framework that utilizes density-functional theory (DFT) in concert with a combined machine-learning model and grand-canonical linear programming for assessing phase stability, phase-fraction, chemical activity and high-temperature survivability of arbitrary HEAs. This framework considers temperature dependent contributions to the Gibbs energy of the competing phases arising from short-range order and vibrational entropy. We demonstrate the effectiveness of the framework by assessing the thermodynamic stability, oxidation behavior, chemical activity, and phase decomposition of body-centered cubic Mo-W-Ta-Ti-Zr refractory HEAs. A total of 51 compositions were analyzed and ranked in order of their survivability based on the Pareto-front analysis. Oxidation was performed at 1373 K on fours samples in air showing the difference in oxidation behavior determined experimentally through scale thickness and their mass changes. The insights on oxidation behavior presented in this work will enable the fast assessment of technologically useful HEAs needed for future structural application in extreme conditions
36 MATERIALS SCIENCE↗
Effects of tensile loading during annealing of alnico melt spun ribbons
Conventional magnetic annealing (MA) of the permanent magnet alloy alnico involves application of an external magnetic field at temperatures within the spinodal decomposition range. This field biases the growth of the Fe-Co rich, ferromagnetic α 1 -phase in an energetically favorable 〈001〉 direction in alignment with the applied field within an Al-Ni rich, paramagnetic α 2 -phase. Utilizing a magnetic field to bias the α 1 -phase may limit alnico from reaching theoretical coercivity due to (1) the field having maximum biasing ability at temperatures near the Curie temperature where large α 1 -phase nanorods form and (2) connectivity of the α 1 -phase occurs unavoidably during MA. Both decrease the effective shape anisotropy of the α 1 -phase, thereby reducing coercivity. Herein, we explore tensile-loading as a biasing mechanism to control and optimize the final alnico nanostructure beyond that achieved by MA. Two samples of melt-spun alnico were heat-treated at 860 °C for 5 minutes: one sample was subjected to 10 MPa tensile stress for comparison with a stress-free control sample. Structural and magnetic characterization revealed that the stress-annealed ribbon sample possessed expected phase assemblages, but was distinguished by a ∼2× larger grain diameter and an elongated anisotropic α 1 -phase within grains that were oriented to a shear stress along 〈001〉 directions at an angle of ∼45° relative to the loading direction. Both types of annealing produced a similar increase in the coercivity and remanence, but a decrease in saturation magnetization.
Rinko, E. A.↗
Borderline first-order magnetic phase transition in AlFe 2 B 2
The thermal evolution of lattice parameters coupled with heat capacity data provide insight into tailorable magnetism-structure attributes in the orthorhombic compound AlFe 2 B 2 that was synthesized with and without small additions of gallium. Temperature-dependent X-ray powder diffraction experiments conducted through the magnetic phase transition reveal that the a- and b-parameters of both samples increase with increasing temperature while the c-parameter decreases. While a weak volumetric thermal expansion is noted over a range of temperatures well below and above the magnetic phase transition, anomalous behavior was observed within the phase transition region itself to reveal a magnetostructural phase transition with borderline first-order character in the Ga-modified sample but of more second-order character in the Ga-free sample. It is established that the nearest-neighbor Fe-Fe interatomic distance within the (ab)-plane plays a dominant role in influencing the magneto-functional response of these compounds. The magnetocaloric properties are discussed in the context of temperature-induced changes of the interatomic bonding that are influenced by the hypothesized presence of iron antisite defects in the AlFe 2 B 2 lattice.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Towards additive manufacturing of magnetocaloric working materials
The feasibility of three-dimensional printing via the Directed Energy Deposition (DED) technique is demonstrated for the ferromagnetic AlFe 2 B 2 (aka 1-2-2) compound, which shows promise as a working material for room-temperature magnetocaloric devices. Like many intermetallic materials, the 1-2-2 compound is brittle at room temperature; not only is it difficult to synthesize from the melt, it is challenging to form it into useful geometries necessary for effective heat transfer in magnetocaloric devices. Using Laser Engineered Net Shaping (LENS TM ) synthesis from two powder precursors, AlB 2 and Fe, samples of simple (rod) and complex (honeycomb) architectures were successfully synthesized. Furthermore, the phase constitution and distribution, magnetic transition temperature, and saturation magnetization determined for the LENS TM -synthesized rod sample are all similar to those obtained for 1-2-2 materials made by conventional casting. Further, the measured magnetic entropy change, as determined from Maxwell's Relations applied to magnetic data, indicates that the magnetocaloric response of the annealed LENS TM -printed rod samples are comparable to those of the 1-2-2 compounds made by conventional techniques. These results confirm that complex magnetofunctional shapes, which are needed for efficient energy conversion in magnetocaloric devices, can be rapidly fabricated from the AlFe 2 B 2 compound.
36 MATERIALS SCIENCE↗
Short- and medium-range orders in Al90Tb10 glass and their relation to the structures of competing crystalline phases
Molecular dynamics simulations using an interatomic potential developed by artificial neural network deep machine learning are performed to study the local structural order in Al90Tb10 metallic glass. We show that more than 80% of the Tb-centered clusters in Al90Tb10 glass have short-range order (SRO) with their 17 first coordination shell atoms stacked in a ‘3661’ or ‘15551’ sequence. Medium-range order (MRO) in Bergman-type packing extended out to the second and third coordination shells is also clearly observed. Analysis of the network formed by the ‘3661’ and ‘15551’ clusters show that ~82% of such SRO units share their faces or vertexes, while only ~6% of neighboring SRO pairs are interpenetrating. Such a network topology is consistent with the Bergman-type MRO around the Tb-centers. Moreover, crystal structure searches using genetic algorithm and the neural network interatomic potential reveal several low-energy metastable crystalline structures in the composition range close to Al 90 Tb 10 . Some of these crystalline structures have the ‘3661’ SRO while others have the ‘15551’ SRO. While the crystalline structures with the ‘3661’ SRO also exhibit the MRO very similar to that observed in the glass, the ones with the ‘15551’ SRO have very different atomic packing in the second and third shells around the Tb centers from that of the Bergman-type MRO observed in the glassy phase.
36 MATERIALS SCIENCE↗
Changes in short- and medium-range order in metallic liquids during undercooling
It has been widely speculated that dominant motifs, such as short-range icosahedral order, can influence glass formation and the properties of glasses. Experimental data on both fragile and strong undercooled liquids demonstrate corresponding changes in their thermophysical properties consistent with increasing development of a network of interconnect motifs based on molecular dynamics. Describing these regions of local order, how they connect, and how they are related to property changes have been challenging issues, both computationally and experimentally. Yet the consensus is that metallic liquids develop interconnected medium-range order consisting of some regions with lower mobility with deeper undercooling. Less well understood is how these motifs (or “crystal genes”) in the liquid can inhibit nucleation in the deeply undercooled liquid or influence phase selection upon devitrification. These motifs tend to have local packing unlike stable compounds with icosahedral order tending to dominate the best glass formers. The underlying kinetic and thermodynamic forces that guide the formation of these motifs and how they interconnect during undercooling remain open questions.
36 MATERIALS SCIENCE↗
Development of interatomic potential for Al–Tb alloys using a deep neural network learning method
An interatomic potential for the Al–Tb alloy around the composition of Al 90 Tb 10 is developed using the deep neural network (DNN) learning method. The atomic configurations and the corresponding total potential energies and forces on each atom obtained from ab initio molecular dynamics (AIMD) simulations are collected to train a DNN model to construct the interatomic potential for the Al–Tb alloy. Here we show that the obtained DNN model can well reproduce the energies and forces calculated by AIMD simulations. Molecular dynamics (MD) simulations using the DNN interatomic potential also accurately describe the structural properties of the Al 90 Tb 10 liquid, such as partial pair correlation functions (PPCFs) and bond angle distributions, in comparison with the results from AIMD simulations. Furthermore, the developed DNN interatomic potential predicts the formation energies of the crystalline phases of the Al–Tb system with an accuracy comparable to ab initio calculations. The structure factors of the Al 90 Tb 10 metallic liquid and glass obtained by MD simulations using the developed DNN interatomic potential are also in good agreement with the experimental X-ray diffraction data. The development of short-range order (SRO) in the Al 90 Tb 10 liquid and the undercooled liquid is also analyzed and three dominant SROs, i.e., Al-centered distorted icosahedron (DISICO) and Tb-centered ‘3661’ and ‘15551’ clusters, respectively, are identified.
36 MATERIALS SCIENCE↗
Competitive devitrification and metastable phase selection in amorphous Al?Sm
Explore the source record for details and available documents.
Meng, F.Q.↗
Role of Hf on Phase Formation in Ti45Zr(38-x)Hf(x)Ni17 Liquids and Solids
Hafnium and zirconium are very similar, with almost identical sizes and chemical bonding characteristics. However, they behave differently when alloyed with Ti and Ni. A sharp phase formation boundary near 18-21 at.% Hf is observed in rapidly-quenched and as-cast Ti45Zr38-xHfxNi17 alloys. Rapidly-quenched samples that contain less than 18 at.% Hf form the icosahedral quasicrystal phase, whiles samples containing more than 21 at.% form the 3/2 rational approximant phase. In cast alloys, a C14 structure is observed for alloys with Hf lower than the boundary concentration, while a large-cell (11.93 ) FCC Ti2Ni-type structure is found in alloys with Hf concentrations above the boundary. To better understand the role of Hf on phase formation, the structural evolution with supercooling and the solidification behavior of liquid Ti45Zr38-xHfxNi17 alloys (x=0, 12, 18, 21, 38) were studied using the Beamline Electrostatic Levitation (BESL) technique using 125keV x-rays on the 6ID-D beamline at the Advanced Photon Source, Argonne National Laboratory. For all liquids primary crystallization was to a BCC solid solution phase; interestly, an increase in Hf concentration leads to a decrease in the BCC lattice parameter in spite of the chemical similarity between Zr and Hf. A Reitveld analysis confirmed that as in the cast alloys, the secondary phase that formed was the C14 below the phase formation boundary and a Ti2Ni-type structure at higher Hf concentrations. Both the liquidus temperature and the reduced undercooling change sharply on traversing the phase formation boundary concentration, suggesting a change in the liquid structure. Structural information from a Honeycutt-Anderson index analysis of reverse Monte Carlo fits to the S(q) liquid data will be presented to address this issue.
Wessels, V.↗
Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere
The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.
Cohen, S. C.↗
Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere
The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.
Cohen, S. C.↗