Search NASA⌕ Search

Engineering topics

Krasik, Ya E

Publications and source records attributed to Krasik, Ya E.

At least 19 records

Time evolution of nanosecond runaway discharges in air and helium at atmospheric pressure

Time- and space-resolved fast framing photography was employed to study the discharge initiated by runaway electrons in air and He gas at atmospheric pressure. Whereas in the both cases, the discharge occurs in a nanosecond time scale and its front propagates with a similar velocity along the cathode-anode gap, the later stages of the discharge differ significantly. In air, the main discharge channels develop and remain in the locations with the strongest field enhancement. In He gas, the first, diode 'gap bridging' stage, is similar to that obtained in air; however, the development of the discharge that follows is dictated by an explosive electron emission from micro-protrusions on the edge of the cathode. These results allow us to draw conclusions regarding the different conductivity of the plasma produced in He and air discharges.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Generation of extreme state of water by spherical wire array underwater electrical explosion

The results of the first experiments on the underwater electrical explosion of a spherical wire array generating a converging strong shock wave are reported. Using a moderate pulse power generator with a stored energy of {<=}6 kJ and discharge current of {<=}500 kA with a rise-time of {approx}300 ns, explosions of Cu and Al wire arrays of different diameters and with a different number and diameter of wires were tested. Electrical, optical, and destruction diagnostics were used to determine the energy deposited into the array, the time-of-flight of the shock wave to the origin of the implosion, and the parameters of water at that location. The experimental and numerical simulation results indicate that the convergence of the shock wave leads to the formation of an extreme state of water in the vicinity of the implosion origin that is characterized by pressure, temperature, and compression factors of (2 {+-} 0.2) Multiplication-Sign 10{sup 12} Pa, 8 {+-} 0.5 eV, and 7 {+-} 0.5, respectively.

42 ENGINEERING↗

Electron emission mechanism during the nanosecond high-voltage pulsed discharge in pressurized air

A comparison between the results of x-ray absorption spectroscopy of runaway electrons (RAEs) generated during nanosecond timescale high-voltage (HV) gas discharge and the simulated attenuation of the x-ray flux produced by the runaway electron spectrum calculated using particle-in-cell numerical modeling of such a type of discharge is presented. The particle-in-cell simulation considered the field and explosive emissions (EEs) of the electrons from the cathode. It is shown that the field emission is the dominant emission mechanism for the short-duration (<2.5 ns) high-voltage pulses, while for the long-duration (>5 ns) high-voltage pulses, the explosive emission is likely to play a significant role.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical simulation of the pre-ionization processes during nanosecond-pulse discharge in nitrogen

The pre-ionization of nitrogen gas by high-voltage nanosecond pulse discharges is studied using one-dimensional particle-in-cell numerical simulations. The comparison between the various mechanisms of pre-ionization, i.e., by runaway electrons, x-rays, and ultraviolet radiation, is presented. It is shown that runaway electrons produce a much higher number of electron-ion pairs than those generated by x-rays, which accompany the process of runaway electron generation. Also, results of simulations showed that among photo-ionization mechanisms the most significant gas pre-ionization is caused by x-rays generated in the process of impact ionization of the K-shell of nitrogen atoms.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical simulations of runaway electron generation in pressurized gases

The results of a numerical simulation of the generation of runaway electrons in pressurized nitrogen and helium gases are presented. It was shown that runaway electrons generation occurs in two stages. In the first stage, runaway electrons are composed of the electrons emitted by the cathode and produced in gas ionization in the vicinity of the cathode. This stage is terminated with the formation of the virtual cathode, which becomes the primary source of runaway electrons in the second stage. Also, it was shown that runaway electrons current is limited by both the shielding of the field emission by the space charge of the emitted electrons and the formation of a virtual cathode. In addition, the influence of the initial conditions, such as voltage rise time and amplitude, gas pressure, and the type of gas, on the processes that accompany runaway electrons generation is presented.

74 ATOMIC AND MOLECULAR PHYSICS↗

Characterization of high-current electron beam interaction with metal targets

The process of electron beam interaction with metal targets was characterized using electrical and optical diagnostics. Electron beams with current density of 5-10 A/cm{sup 2}, electron energy up to 120 keV, pulse duration up to 200 {mu}s, and cross-sectional area of 8-30 cm{sup 2} at the target surface were generated by GESA I and GESA II facilities. Streak imaging of the target surface specular reflectivity was used to determine the onset of melting and re-solidification of the target surface. Using time- and space-resolved schlieren imaging, the evolution of surface irregularities was studied. Experimental and numerical investigations of the neutral flow evaporated from the target surface showed a neutral density of {approx}10{sup 19} cm{sup -3} in the vicinity of the target and neutral velocities up to 2 x 10{sup 5} cm/s. Framing and streak images of visible light emission were used to study the temporal evolution of the target surface plasma and vapors. Time- and space-resolved spectroscopy was applied to determine the surface plasma density and temperature, which were found to be {approx}10{sup 14} cm{sup -3} and {<=}1 eV, respectively. Because of this small plasma density, electric fields in the plasma sheath are not sufficient to cause electrohydrodynamic instability of the liquid target surface. However, hydrodynamic instabilities due to the intense neutral flow observed in experimental and numerical studies are likely to be responsible for the growth of wavelike irregularities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluation of electrical conductivity and equations of state of non-ideal plasma through microsecond timescale underwater electrical wire explosion

Experimental and simulation results of underwater electrical Cu, Al, and W wire explosions in the microsecond timescale are presented. It was shown that the electrical conductivity results for Cu and Al agree well with modified Lee-More and quantum molecular dynamic models for temperatures above 10 kK. The equation of state (EOS) values based on SESAME tables for Cu and Al were slightly modified for intermediate temperatures in order to obtain fitting between experimental and simulated exploding wire radial expansion. Also, it was shown that the electrical conductivity results and the EOS evaluation differ significantly from the results obtained in nanosecond timescale experiments. Finally, it was found that underwater electrical W wire explosion is characterized by the appearance of non-uniformities along the z-axis of the wire. This phenomena adds uncertainty to the possibility of applying this type of experiments for evaluation of the electrical conductivity and EOS of W.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Generation of a 400 GPa pressure in water using converging strong shock waves

Results related to the generation of an extreme state of water with pressure up to (4.3 {+-} 0.2){center_dot}10{sup 11} Pa, density up to 4.2 {+-} 0.1 g/cm{sup 3}, and temperature up to 2.2 {+-} 0.1 eV in the vicinity of the implosion axis of a converging strong shock wave are reported. The shock wave was produced by the underwater electrical explosion of a cylindrical Cu wire array. A {approx}8 kJ pulse generator with a current amplitude {<=}550 kA and rise time of 350 ns was used to explode arrays having varying lengths, radii, and number of wires. Hydrodynamic numerical simulations coupled to the experimental data of the shock wave propagation in water, rate of energy deposition into the array, and light emission from the compressed water in the vicinity of the implosion axis were used to determine the pressure, density, and temperature profiles during the implosion. Results of a comparison between these parameters obtained with the SESAME and quantum molecular dynamics data bases of equation of state for water are reported as well. Also, the dependences of the maximal pressure in the vicinity of the implosion axes on the array radius and the deposited energy density per unit length are reported.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Space- and time-resolved characterization of nanosecond time scale discharge at pressurized gas

The phenomenon of ultra-fast electrical gas breakdown was investigated. Nanosecond high-voltage pulses with durations of 1 and 5 ns and amplitudes of 100 and 200 kV, respectively, were used to study the parameters of the discharge in a pressured (1-7) x 10{sup 5} Pa air-filled gap. The development of the discharge and the plasma propagation velocity was examined using optical fast frame imaging. The generation of runaway electrons in the breakdown process was confirmed by electron imaging and time-resolved x-ray diagnostics. Runaway electron beam energy distribution was obtained for a 1 ns duration high-voltage pulse. The origin and the role of runaway electrons in the discharge initiation are also discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-current diode with ferroelectric plasma source-assisted hollow anode

The operation of a ferroelectric plasma source-assisted hollow anode (HA) electron source in a vacuum diode powered by an {approx}200 kV and {approx}400 ns pulsed generator was studied using time- and space-resolved laser induced fluorescence diagnostics. It was found that the plasma ion ''temperature'' in the vicinity of the HA output grid increases up to {approx}15 eV during the accelerating pulse, which is consistent with a model of the potential screening of the grid by the randomly moving ions [Phys. Plasmas 13, 073506 (2006)]. Also it was shown that the increase in the HA plasma potential up to several kilovolts because of the appearance of a noncompensated ion charge in the HA bulk plasma due to electrons fast extraction, leads to explosive emission centers being generated at the HA grid and to nonuniformity in the cross-sectional electron beam current density. Finally, the plasma prefilled mode of diode operation was studied using a simple one-dimensional model of the plasma erosion and the HA plasma electron heating by energetic ions was considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of electrical conductivity and equations of state of non-ideal plasma through underwater electrical wire explosion

The results of experiments and magnetohydrodynamic simulations of nanosecond time scale underwater electrical explosions of Al, Cu, and W wires are presented. Experiments were performed using a nanosecond pulsed generator with a {approx}30 kA amplitude and {approx}60 ns rise time current pulse. The electrical conductivity of the tested materials in the density and temperature ranges of 0.1-20 g/cm{sup 3} and 0.03-8 eV, respectively, is presented. It is shown that for the physical conditions obtained in these experiments, the equation of state data used in the SESAME tables must be modified in order to reproduce the experimental results. Also, it was shown that the electrical conductivity of the metals does not consistently fit over the entire range of experimental conditions with either of the transport models presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma formation in a double-gap vircator

Time-resolved light emission imaging was used to observe the plasma formation within the cavity of the double-gap vircator powered by a sub-microsecond generator ({approx}500 kV, {approx}10 kA, {approx}500 ns). The vircator generated well reproducible S-band microwave pulses of {approx}200 MW peak power and up to 200 ns full duration. The plasma light emission was observed {approx}30 ns prior to the ending of the generated microwave pulses at the surface of the aluminum foil separating the vircator cavity gaps, in the gap where the virtual cathode is formed. Estimations showed that the energy deposition into the foil by the high-current electron beam is sufficient for the surface plasma formation. The plasma ions accelerated toward the virtual cathode neutralize its electron space charge. The latter was confirmed by the increase in the electron current transmitted through the vircator cavity. In addition, the time of the plasma appearance was determined by comparing the measured transmitted current with that following from the one-dimensional model of a stationary un-neutralized two-stream electron flow. This time agrees with the maximum of the microwave power observed in the experiments, thus showing that the plasma ions cause the termination of the microwave generation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Extreme water state produced by underwater wire-array electrical explosion

The generation of an extreme water state (130 GPa, 5000 K, and 3.4 g/cm{sup 3}) which is characterized as dense plasma at the axis of a converging shock wave is reported. A 4 kJ pulse generator was used to explode a 40 Cu-wire array, generating a cylindrical shock wave. The measured shock wave trajectory and energy deposited into the water flow were used in hydrodynamic simulations coupled with the equation of state to determine the water parameters. The temperature estimated using the emission data of water in the vicinity of the implosion axis agrees with the simulation results, indicating shock wave symmetry in such extreme conditions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser induced fluorescence of the ferroelectric plasma source assisted hollow anode discharge

Parameters of the plasma produced by a ferroelectric plasma source (FPS) assisted high-current ({approx}1 kA), hollow anode (HA), low-pressure (10{sup -4} Torr) Ar gas discharge were studied using a time- and space-resolved laser induced fluorescence (LIF) diagnostic technique. It was shown that the plasma filling of the HA cavity occurs due to the expansion of the plasma flows generated by the FPSs with a gradual time-dependent increase in the plasma density along the length of the HA cavity. These data were verified by the results of one-dimensional modeling of the plasma expansion in vacuum and time-dependent collisional-radiative modeling. Also, LIF diagnostics, which was tested on the saturation effect both experimentally and numerically, showed that the plasma ion temperature gradually increases during the discharge reaching {approx}9 eV at its end. Various phenomena (plasma kinetic instabilities, charge-exchange processes during the plasma ion interaction with the HA walls, and the model of neutral atoms ionization inside the Debay's sphere), which could be responsible for such ion temperature, were considered.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Polarimetry and Schlieren diagnostics of underwater exploding wires

Nondisturbing laser-probing polarimetry (based on the Faraday and Kerr effects) and Schlieren diagnostics were used in the investigation of underwater electrical wire explosion. Measuring the polarization plane rotation angle of a probing laser beam due to the Faraday effect allows one to determine an axially resolved current flowing through the exploding wire, unlike commonly used current probes. This optical method of measuring current yields results that match those obtained using a current viewing resistor within an accuracy of 10%. The same optical setup allows simultaneous space-resolved measurement of the electric field using the Kerr effect. It was shown that the maximal amplitude of the electric field in the vicinity of the high-voltage electrode is approx80 kV/cm and that the radial electric field is <1 MV/cm during the wire explosion. Finally, it was shown that the use of Schlieren diagnostics allows one to obtain qualitatively the density distribution behind the shock wave front, which is important for the determination of the energy transfer from the discharge channel to the generated water flow.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electron beam and plasma modes of a channel spark discharge operation

Parameters of a modified pulsed channel spark discharge (CSD), operating at a repetition rate up to 100 Hz at Ar gas pressures of 10{sup -3} and 10{sup -4} Torr and of the generated electron beam, were studied using different electrical, optical, and x-ray diagnostics. It was shown that efficient (up to approx74%) transfer of the initially stored energy to the energetic electron beam is realized only at the pressure of 10{sup -4} Torr. Conversely, at the pressure of 10{sup -3} Torr, less than 10% of the stored energy is acquired by the energetic electrons. It was found that the energetic electron beam generation is limited by the expansion of the cathode and anode plasmas and by the formation of plasma inside the gap between the CSD capillary output and the anode. It was also found that the plasma, which acquires the hollow cathode potential, is already formed at the beginning of the CSD operation inside the capillary, and the electron emission occurs from the capillary output plasma boundary. Finally, it was shown that the electron beam energy spectrum differs significantly from the energy spectrum, which one may expect in the case of the planar diode operation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Addressing the efficiency of the energy transfer to the water flow by underwater electrical wire explosion

Experimental and hydrodynamic simulation results of submicrosecond time scale underwater electrical explosions of planar Cu and Al wire arrays are presented. A pulsed low-inductance generator having a current amplitude of up to 380 kA was used. The maximum current rise rate and maximum power achieved during wire array explosions were dI/dt<=830 A/ns and approx10 GW, respectively. Interaction of the water flow generated during wire array explosion with the target was used to estimate the efficiency of the transfer of the energy initially stored in the generator energy to the water flow. It was shown that efficiency is in the range of 18%-24%. In addition, it was revealed that electrical explosion of the Al wire array allows almost double the energy to be transferred to the water flow due to efficient combustion of the Al wires. The latter allows one to expect a significant increase in the pressure at the front of converging strong shock waves in the case of cylindrical Al wire array underwater explosion.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Plasma parameters of an active cathode during relativistic magnetron operation

The results of time- and space-resolved spectroscopic studies of the plasma produced at the surface of the ferroelectric cathode during the operation of an S-band relativistic magnetron generating approx50 MW microwave power at f=3005 MHz and powered by a linear induction accelerator (LIA) (150 kV, 1.5 kA, 250 ns) are presented. The surface plasma was produced by a driving pulse (3 kV, 150 ns) prior to the application of the LIA accelerating high-voltage pulse. The cathode plasma electron density and temperature were obtained by analyzing hydrogen H{sub a}lpha and H{sub b}eta, and carbon ions CII and CIII spectral lines, and using the results of nonstationary collision radiative modeling. It was shown that the microwave generation causes an increase in plasma ion and electron temperature up to approx4 and approx7 eV, respectively, and the plasma density increases up to approx7x10{sup 14} cm{sup -3}. Estimates of the plasma transport parameters and its interaction with microwave radiation are also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗