Search NASA⌕ Search

Engineering topics

Krave, Steven

Publications and source records attributed to Krave, Steven.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Application of Distributed Fiber Optic Strain Sensors to LMQXFA Cold Mass Welding

The future High Luminosity upgrade of the Large Hadron Collider (HL-LHC) at CERN will include the low-beta inner triplets (Q1, Q2a/b, Q3) for two LHC insertion regions. The Q1, Q3 components consist of eight 10 m-long LMQXFA cryo-assemblies fabricated by the HL-LHC Accelerator Upgrade Project. Each LMQXFA Cold mass contains two Nb 3 Sn magnets connected in series. A stainless-steel shell is welded around the two magnets before the insertion into the cryostat. There is a limit on how much coil preload increase induced by the shell welding is allowed. Distributed Rayleigh backscattering fiber optics sensors were used for the first time to obtain a strain map over a wide area of a Nb 3 Sn magnet cold mass shell. Finally, data were collected during welding of the first LMQXFA cold mass and the results confirm that the increase of the coil pole azimuthal pre-stress after welding do not exceed requirements.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Study of the Heater-Coil Electrical Insulation for the HL-LHC Low Beta Quadrupoles

In the framework of the HL-LHC project, the present LHC low-β superconducting quadrupoles will be substituted with higher performance Nb 3 Sn magnets (MQXF) with 11.4 T coil peak field. MQXF coils are impregnated with epoxy resin to reduce risk of stress concentration on the brittle conductor. The magnet quench protection is provided by CLIQ and quench heaters to ensure a redundant system. Quench heaters are impregnated with the coils in order to have suitable thermal contact with them, and to prevent the hot spot temperature from exceeding 350K during normal operation in case of a quench. Quench heaters are insulated from the coil by S-2 Glass and polyimide. Here, the test of the first MQXF prototype (4 m long) MQXFAP1 was stopped by a coil-to-ground short circuit triggered by a heater-to-coil short. This issue triggered a root analysis of the causes of this short. Here we prove that the use of a non-conforming cloth in coil impregnation, further weakened by non-conforming high voltage test, has triggered the shorts. Moreover, we present an analysis of the heater-to-coil insulation strength, showing the role of blistering phenomena and how they are triggered by a combination of magnet powering and heater firing.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Exploring New Resin Systems for Nb3Sn Accelerator Magnets

Epoxy resins have long been a focus of magnet design. They provide strength and stability to the superconductor, to allow coil fabrication and consistent magnet performance. They are often cited as a main contributor to magnet performance, often as a limiting factor, from epoxy cracking and energy release. New resin systems are being designed to improve magnet quench and training performance through several means. Baseline candidate resin systems are evaluated for neat resin mechanical properties as well as behavior in Nb 3 Sn subscale composites. Furthermore, this data feeds additional resin system tuning to meet the goals stated above.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Assessment of MQXF Quench Heater Insulation Strength and Test of Modified Design

The HL-LHC interaction region magnet triplets (Q1,Q2, and Q3) will be composed of superconducting Nb 3 Sn quadrupoles. The MQXF quadrupole protection system is based on CLIQ (Coupling-Loss Induced Quench system) and outer layer quench heaters. Furthermore, this paper reports a summary of quench heaters to coil high voltage tests performed on MQXF short and long coils in air after fabrication, and in air and He gas after magnet training. Breakdown voltage values demonstrate good margin with respect to the Electrical design criteria for the HL-LHC inner triplet mag-nets. A modification in the quench heater installation-with an extra layer of fiber glass between the coil and the quench heater trace-has been proposed and tested in a mirror magnet to further increase electrical margins. Results demonstrated improvements of high voltage margin at the expense of a clear increase of hot spot temperature.The baseline heater to coil insulation was assessed to be able to guarantee safe operation for the Nb 3 Sn quadrupole magnets for the interaction regions of HL-LHC.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Intelliquench: An Adaptive Machine Learning System for Detection of Superconducting Magnet Quenches

In superconducting magnets, the irreversible transition of a portion of the conductor to resistive state is called a “quench.” Having large stored energy, magnets can be damaged by quenches due to localized heating, high voltage, or large force transients. Unfortunately, current quench protection systems can only detect a quench after it happens, and mitigating risks in Low Temperature Superconducting (LTS) accelerator magnets often requires fast response (down to ms). Additionally, protection of High Temperature Superconducting (HTS) magnets is still suffering from prohibitively slow quench detection. In this study, we lay the groundwork for a quench prediction system using an auto-encoder fully-connected deep neural network. After dynamically trained with data features extracted from acoustic sensors around the magnet, the system detects anomalous events seconds before the quench in most of our data. While the exact nature of the events is under investigation, we show that the system can “forecast” a quench before it happens under magnet training conditions through a randomized experiment. This opens up the way of integrated data processing, potentially leading to faster and better diagnostics and detection of magnet quenches

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Lessons Learned From the Prototypes of the MQXFA Low-Beta Quadrupoles for HL-LHC and Status of Production in the US

With the successful test of the first two pre-series magnets the US HL-LHC Accelerator Upgrade Project has started production of the MQXFA magnets to be used in Q1/Q3 inner triplet elements of the HL-LHC. This good start comes after the test of two prototypes with limited performance, and it demonstrates the importance of learning from past issues. Therefore, in this paper we want to share the most important lessons learned so far, focusing on those which may be more interesting for similar projects. Additionally, we will present the status of MQXFA fabrication in the US.

43 PARTICLE ACCELERATORS↗