Search NASA⌕ Search

Engineering topics

Kreeger, Richard E.

Publications and source records attributed to Kreeger, Richard E..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Application of Extended Messinger Models to Complex Geometries

Since, ice accretion can significantly degrade the performance and the stability of an airborne vehicle, it is imperative to be able to model it accurately. While ice accretion studies have been performed on airplane wings and helicopter blades in abundance, there are few that attempt to model the process on more complex geometries such as fuselages. This paper proposes a methodology that extends an existing in-house Extended Messinger solver to complex geometries by introducing the capability to work with unstructured grids and carry out spatial surface streamwise marching. For the work presented here commercial solvers such as STAR-CCM+ and ANSYS Fluent are used for the flow field and droplet dispersed phase computations. The ice accretion is carried out using an in-house icing solver called GT-ICE. The predictions by GT-ICE are compared to available experimental data, or to predictions by other solvers such as LEWICE and STAR-CCM+. Three different cases with varying levels of complexity are presented. The first case considered is a commercial transport airfoil, followed by a three-dimensional MS(1)-317 swept wing. Finally, ice accretion calculations performed on a Robin fuselage have been discussed. Good agreement with experimental data, where applicable, is observed. Differences between the ice accretion predictions by different solvers have been discussed.

Gupta, Avani↗
NASA NTRS2020

Effects of Hydrogen Bonding and Molecular Chain Flexibility of Substituted n-Alkyldimethylsilanes On Impact Ice Adhesion Shear Strength

The effects of hydrogen bonding and molecular flexibility upon ice adhesion shear strength were investigated using aluminum substrates coated with substituted n-alkyldimethylalkoxysilanes. The location of the chemical group substitution was on the opposing end of the linear n-alkyl chain with respect to silicon. Three hydrogen-bonding characteristics were evaluated: 1) non-hydrogen bonding, 2) donor/acceptor, and 3) acceptor. Varying the length of the n-alkyl chain provided an assessment of molecular chain flexibility. Coated and uncoated aluminum surfaces were characterized by receding water contact angle and surface roughness. Ice adhesion shear strength was determined in the Adverse Environment Rotor Test Stand facility from -16 to -8°C that simulated aircraft in-flight icing conditions within the FAR Part 25/29 Appendix C icing envelope. Surface roughness of the coatings was similar allowing for comparison of the test results. An adhesion reduction factor, based on the ice adhesion shear strength data with respect to uncoated aluminum obtained at the same temperature, was calculated to compare the data. The results revealed complex interactions with impacting supercooled water droplets that were interdependent upon ice accretion temperature, surface energy characteristics of water and ice, hydrogen bonding characteristic of the substituent, and length of the n-alkyl chain. To aid in explaining the results, 1) changes in the surface energy component (i.e., non-polar and polar) values that water undergoes during its’ phase change from liquid to solid that arise from the freezing of impacting supercooled water droplets on the surface depended upon the temperature during accretion were taken into account and 2) the physical properties (i.e., water solubility and melting point) of small compounds analogous to the substituted n-alkyldimethylalkoxysilanes used in this study were compared.

Smith, Joseph G.↗
NASA NTRS2019

An Investigation into the Grain Structure of Impact Ice

To design effective anti-icing and de-icing technology for aircraft, scientists and engineers must obtain a fundamental understanding of the microstructural characteristics of impact ice. This study investigates the effects of icing parameters, such as airspeed and liquid water content (LWC), on impact ice microstructure near the interface to a metal substrate. Ice samples were accreted in the NASA Glenn Icing Research Tunnel and tested in the NASA Revolutionary Icing Materials Evaluation Laboratory. A microtome was used to shave down the ice to a thickness of < 1 mm for examination under a microscope. Samples were imaged at multiple magnifications using bright field imaging. The average grain size was determined for each sample in accordance with ASTM standard methods, and relationships between airspeed, LWC, and grain size were identified. It was observed that the average grain area in a given cross-section was linearly related to the distance of the cross-section from the metal surface. Finally, the effects of annealing and sublimation on the microstructure were also explored. Results show significant variation in the grain structure, suggesting a means by which icing condition influences adhesion strength.

grain↗
NASA NTRS2019

NASA Workshop on Low Ice Adhesion Materials

The first NASA Workshop on Low Ice Adhesion Materials was held on Thursday, August 10, 2017, at the Ohio Aerospace Institute in Cleveland, Ohio. This meeting allowed government, industry, and academia to meet in a collaborative environment to discuss the future of “icephobics” research for inflight icing. NASA presented its ongoing research, and organizations that currently have partnerships with NASA presented their recent findings. Presenters from academia included Iowa State University, Mississippi State University, Pennsylvania State University, and the University of Michigan. Presenters from industry included United Technologies Aerospace Systems; Nanosonic, Inc.; and NEI Corporation. Researchers from NASA Glenn Research Center, NASA Langley Research Center, and the Office of Naval Research also shared their current research. There were over 60 participants who attended the conference plus more than 10 who participated remotely. The meeting was highly successful, and although a second such conference was proposed, it is anticipated that future technical presentations on the subject(s) will take place in other venues. Presentations from this workshop that are suitable for public release are included in this document. This effort supports both the Advanced Air Transport Technology (AATT) Project and the Revolutionary Vertical Lift Technology (RVLT) Project.

Kreeger, Richard E.↗
NASA NTRS2018

Development and Validation of Physics Based Models for Ice Shedding

Calculations for ice accretion and shedding are presented for a model scale rotor in hover. The aerodynamic characteristics of the rotor are first computed using a combined blade element-momentum theory. The effective angles of attack, and the local flow velocity are used within the NASA Glenn solver LEWICE to estimate the collection efficiency. The computed convection efficiency and the surface pressure distribution from a panel method within LEWICE are used to estimate the ice accretion over the rotor blades over an elapsed time interval. Finally, a force balance approach is used to establish shedding events where the centrifugal force over the ice mass exceeds the adhesive forces at the rotor surface and the cohesive forces between adjacent masses of ice. Preliminary comparisons with test data acquired at the Pennsylvania State Icing Research Tunnel are presented. Sensitivity of the ice shedding events to surface roughness, adhesive strength, cohesive strength, and ambient conditions is discussed.

Gupta, Avani↗
NASA NTRS2018

The Adhesion Strength of Impact Ice Measured Using a Modified Lap Joint Test

Numerous methodologies have been utilized to measure the adhesion strength of impact ice, and the data reported in the literature varies significantly from test to test. In order to initiate an investigation to determine the cause of this disparity, a new test methodology has been developed and utilized in the Icing Research Tunnel at the NASA Glenn Research Center. Data was obtained while varying the temperature, test section velocity, and cloud droplet mean volumetric diameter. The first data set acquired using this new test method is presented. New trends demonstrate the effect of annealing ice samples, with temperature being a key variable. Observations during the test and analysis of the results suggest the presence of large residual stresses in the samples.

Work, Andrew H., Jr.↗
NASA NTRS2018

Collaborative Experiments and Computations in Aircraft Icing

The formation of ice over lifting surfaces can affect aerodynamic performance. The ability to predict ice accumulation and the resulting degradation in vehicle performance is essential to determine the limitations of aircraft in icing encounters. The consequences of underestimating performance degradation can be serious and so it is important to produce accurate predictions, particularly for severe icing conditions. The simulation of ice accretion is a challenging multidisciplinary problem that requires close collaboration between the computational and ground test communities. This paper describes three recent case studies and the lessons learned through collaborative experiments and computations in aircraft icing- one for large commercial transports, one for rotorcraft, and one dealing with icing on regional jets.

and rotorcraft↗
NASA NTRS2016

Analysis and Prediction of Ice Shedding for a Full-Scale Heated Tail Rotor

When helicopters are to fly in icing conditions, it is necessary to consider the possibility of ice shed from the rotor blades. In 2013, a series of tests were conducted on a heated tail rotor at NASA Glenn's Icing Research Tunnel (IRT). The tests produced several shed events that were captured on camera. Three of these shed events were captured at a sufficiently high frame rate to obtain multiple images of the shed ice in flight that had a sufficiently long section of shed ice for analysis. Analysis of these shed events is presented and compared to an analytical Shedding Trajectory Model (STM). The STM is developed and assumes that the ice breaks off instantly as it reaches the end of the blade, while frictional and viscous forces are used as parameters to fit the STM. The trajectory of each shed is compared to that predicted by the STM, where the STM provides information of the shed group of ice as a whole. The limitations of the model's underlying assumptions are discussed in comparison to experimental shed events.

rotorcraft↗
NASA NTRS2016

Analysis and Prediction of Ice Shedding for a Full-Scale Heated Tail Rotor

When helicopters are to fly in icing conditions, it is necessary to consider the possibility of ice shed from the rotor blades. In 2013, a series of tests were conducted on a heated tail rotor at NASA Glenn's Icing Research Tunnel (IRT). The tests produced several shed events that were captured on camera. Three of these shed events were captured at a sufficiently high frame rate to obtain multiple images of the shed ice in flight that had a sufficiently long section of shed ice for analysis. Analysis of these shed events is presented and compared to an analytical Shedding Trajectory Model (STM). The STM is developed and assumes that the ice breaks off instantly as it reaches the end of the blade, while frictional and viscous forces are used as parameters to fit the STM. The trajectory of each shed is compared to that predicted by the STM, where the STM provides information of the shed group of ice as a whole. The limitations of the model's underlying assumptions are discussed in comparison to experimental shed events.

icing↗
NASA NTRS2016

Effect of Molecular Flexibility upon Ice Adhesion Shear Strength

Ice formation on aircraft surfaces effects aircraft performance by increasing weight and drag leading to loss of lift. Current active alleviation strategies involve pneumatic boots, heated surfaces, and usage of glycol based de-icing fluids. Mitigation or reduction of in-flight icing by means of a passive approach may enable retention of aircraft capabilities, i.e., no reduction in lift, while reducing the aircraft weight and mechanical complexity. Under a NASA Aeronautics Research Institute Seedling activity, the effect of end group functionality and chain length upon ice adhesion shear strength (IASS) was evaluated with the results indicating that chemical functionality and chain length (i.e. molecular flexibility) affected IASS. Based on experimental and modeling results, diamine monomers incorporating molecular flexibility as either a side chain or in between diamine functionalities were prepared, incorporated into epoxy resins that were subsequently used to fabricate coatings on aluminum substrates, and tested in a simulated icing environment. The IASS was found to be lower when molecular flexibility was incorporated in the polymer chain as opposed to a side chain.

Smith, Joseph G.↗
NASA NTRS2015

Ice Particle Impacts on a Flat Plate

An experimental study was conducted at the Ballistic Laboratory of NASA Glenn Research Center to study the impact of ice particles on a stationary flat surface target set at 45 degrees with respect to the direction of motion of the impinging particle (Figure 1). The experiment is part of NASA efforts to study the physics involved in engine power-loss events due to ice-crystal ingestion and ice accretion formation inside engines. These events can occur when aircraft encounter high-altitude convective weather.

ice particle↗
NASA NTRS2015

The Effect of Surface Chemical Functionality Upon Ice Adhesion

In nature, anti-freeze proteins present in fish utilize specific organic functionalities to disrupt ice crystal formation and propagation. Based on these structures, surfaces with controlled chemical functionality and chain length were evaluated both experimentally and computationally to assess the effect of both parameters in mitigating ice formation. Linear aliphatic dimethylethoxysilanes terminated with methyl or hydroxyl groups were prepared, characterized, and used to coat aluminum. The effect upon icing using a microdroplet freezing apparatus and the Adverse Environment Rotor Test Stand found hydroxyl-terminated materials exhibited a greater propensity for ice formation and adhesion. Molecular dynamics simulations of a silica substrate bearing functionalized species of similar composition were brought into contact with a pre-equilibrated ice crystal. Several parameters including chain mobility were monitored to ascertain the size of a quasi-liquid layer. The studies suggested that chain mobility affected the interface between ice and the surface more than terminal group chemical composition.

Smith, Joseph G., Jr.↗
NASA NTRS2014

Hydrogen-Bonding Surfaces for Ice Mitigation

Ice formation on aircraft, either on the ground or in-flight, is a major safety issue. While ground icing events occur predominantly during the winter months, in-flight icing can happen anytime during the year. The latter is more problematic since it could result in increased drag and loss of lift. Under a Phase I ARMD NARI Seedling Activity, coated aluminum surfaces possessing hydrogen-bonding groups were under investigation for mitigating ice formation. Hydroxyl and methyl terminated dimethylethoxysilanes were prepared via known chemistries and characterized by spectroscopic methods. These materials were subsequently used to coat aluminum surfaces. Surface compositions were based on pure hydroxyl and methyl terminated species as well as mixtures of the two. Coated surfaces were characterized by contact angle goniometry. Receding water contact angle data suggested several potential surfaces that may exhibit reduced ice adhesion. Qualitative icing experiments performed under representative environmental temperatures using supercooled distilled water delivered via spray coating were inconclusive. Molecular modeling studies suggested that chain mobility affected the interface between ice and the surface more than terminal group chemical composition. Chain mobility resulted from the creation of "pockets" of increased free volume for longer chains to occupy.

Smith, Joseph G., Jr.↗
NASA NTRS2014

Ice Shapes on a Tail Rotor

Testing of a thermally-protected helicopter rotor in the Icing Research Tunnel (IRT) was completed. Data included inter-cycle and cold blade ice shapes. Accreted ice shapes were thoroughly documented, including tracing, scanning and photographing. This was the first time this scanning capability was used outside of NASA. This type of data has never been obtained for a rotorcraft before. This data will now be used to validate the latest generation of icing analysis tools.

Airfoil↗
NASA NTRS2014

Implementation and Validation of 3-D Ice Accretion Measurement Methodology

A research program has been implemented to develop and validate the use of a commercial 3-D laser scanning system to record ice accretion geometry in the NASA Icing Research Tunnel. A main component of the program was the geometric assessment of the 3- D laser scanning system on a 2-D (straight wing) and a 3-D (swept wing) airfoil geometries. This exercise consisted of comparison of scanned ice accretion to castings of the same ice accretion. The scan data were also used to create rapid prototype artificial ice shapes that were scanned and compared to the original ice accretion. The results from geometric comparisons on the straight wing showed that the ice shape models generated through the scan/rapid prototype process compared reasonably well with the cast shapes. Similar results were obtained with the geometric comparisons on the swept wing. It was difficult to precisely compare the scans of the cast shapes to the original ice accretion scans because the cast shapes appear to have shrunk during the mold/casting process by as much as 0.10-inch. However the comparison of the local ice-shape features were possible and produced better results. The rapid prototype manufacturing process was shown to reproduce the original ice accretion scan normally within 0.01-inch.

Icing↗
NASA NTRS2014

Ice Particle Impacts on a Moving Wedge

This work presents the results of an experimental study of ice particle impacts on a moving wedge. The experiment was conducted in the Adverse Environment Rotor Test Stand (AERTS) facility located at Penn State University. The wedge was placed at the tip of a rotating blade. Ice particles shot from a pressure gun intercepted the moving wedge and impacted it at a location along its circular path. The upward velocity of the ice particles varied from 7 to 12 meters per second. Wedge velocities were varied from 0 to 120 meters per second. Wedge angles tested were 0, 30, 45, and 60. High speed imaging combined with backlighting captured the impact allowing observation of the effect of velocity and wedge angle on the impact and the post-impact fragment behavior. It was found that the pressure gun and the rotating wedge could be synchronized to consistently obtain ice particle impacts on the target wedge. It was observed that the number of fragments increase with the normal component of the impact velocity. Particle fragments ejected immediately after impact showed velocities higher than the impact velocity. The results followed the major qualitative features observed by other researchers for hailstone impacts, even though the reduced scale size of the particles used in the present experiment as compared to hailstones was 4:1.

Impacts↗
NASA NTRS2014

Ice Particle Impacts on a Moving Wedge

This work presents the results of an experimental study of ice particle impacts on a moving wedge. The experiment was conducted in the Adverse Environment Rotor Test Stand (AERTS) facility located at Penn State University. The wedge was placed at the tip of a rotating blade. Ice particles shot from a pressure gun intercepted the moving wedge and impacted it at a location along its circular path. The upward velocity of the ice particles varied from 7 to 12 meters per second. Wedge velocities were varied from 0 to 120 meters per second. Wedge angles tested were 0 deg, 30 deg, 45 deg, and 60 deg. High speed imaging combined with backlighting captured the impact allowing observation of the effect of velocity and wedge angle on the impact and the post-impact fragment behavior. It was found that the pressure gun and the rotating wedge could be synchronized to consistently obtain ice particle impacts on the target wedge. It was observed that the number of fragments increase with the normal component of the impact velocity. Particle fragments ejected immediately after impact showed velocities higher than the impact velocity. The results followed the major qualitative features observed by other researchers for hailstone impacts, even though the reduced scale size of the particles used in the present experiment as compared to hailstones was 4:1.

Roughness↗