Role of the Ionomer in Supporting Electrolyte-Fed Anion Exchange Membrane Water Electrolyzers
Not Available
Engineering topics
Publications and source records attributed to Kreider, Melissa E..
Not Available
Metal-organic frameworks (MOFs) offer an interesting opportunity for catalysis, particularly for metal-nitrogen-carbon (M-N-C) motifs by providing an organized porous structural pattern and well-defined active sites for the oxygen reduction reaction (ORR), a key need for hydrogen fuel cells and related sustainable energy technologies. Here, in this work, we leverage electrochemical testing with computational models to study the electronic and structural properties in these systems and their relationship to ORR activity and stability based on dual transitional metal centers. These consists of two M1 metals with amine nodes coordinated to a single M2 metal with a phthalocyanine linker, where M1/M2 = Co, Ni, or Cu. Co-based metal centers, in particular Ni-Co, demonstrate the highest overall activity of all nine tested MOFs. Computationally, we identify the dominance of Co-sites, relative higher importance of the M2 site, and the role of layer M1 interactions on the ORR activity. Selectivity measurements indicate that M1 sites of MOFs, particularly Co, exhibits lowest (< 4%), and Ni demonstrates highest (>46%) two-electron selectivity, in good agreement with computational studies. Direct in-situ stability characterization, measuring dissolved metal ions, and calculations, using an alkaline stability metric, confirm that Co is the most stable metal in the MOF, while Cu exhibits notable instability at the M1. Overall, this study reveals how atomistic coupling of electronic and structural properties affects the ORR performance of dual site MOF catalysts and opens new avenues for tunable design and future development of these systems for practical electrochemical applications.
Computationally predicting the performance of catalysts under reaction conditions is a challenging task due to the complexity of catalytic surfaces and their evolution in situ, different reaction paths, and the presence of solid-liquid interfaces in the case of electrochemistry. We demonstrate here how relatively simple machine learning models can be found that enable prediction of experimentally observed onset potentials. Inputs to our model are comprised of data from the oxygen reduction reaction on non-precious transition-metal antimony oxide nanoparticulate catalysts with a combination of experimental conditions and computationally affordable bulk atomic and electronic structural descriptors from density functional theory simulations. From human-interpretable genetic programming models, we identify key experimental descriptors and key supplemental bulk electronic and atomic structural descriptors that govern trends in onset potentials for these oxides and deduce how these descriptors should be tuned to increase onset potentials. Here, we finally validate these machine learning predictions by experimentally confirming that scandium as a dopant in nickel antimony oxide leads to a desired onset potential increase. Macroscopic experimental factors are found to be crucially important descriptors to be considered for models of catalytic performance, highlighting the important role machine learning can play here even in the presence of small datasets.
Anion exchange membrane water electrolyzers (AEMWEs) can generate hydrogen with a pure water feed using noble metal-free catalysts. Here, the development of highly active and stable catalysts for oxygen evolution reaction (OER) is required for improving performance of AEMWEs systems. Ni-Fe (oxy)hydroxides show high OER catalytic activity in alkaline media, but typically have low surface area. In this work, we investigate a series of Ni-Fe oxides with high surface area and disordered morphology, obtained using an aerogel synthesis method. We evaluate the impact of different synthesis variables on the OER activity and demonstrate that heat treatment at high temperatures generates more ordered structure, resulting in a decrease in OER activity. Advanced characterization reveals that maintaining highly disordered and porous structure of the aerogel is essential to achieving high OER activity, as it enables the formation of highly OER-active lamellar structures of the catalyst.
This review discusses recent insights in catalyst layer design strategies for anion exchange membrane water electrolyzers, including electrode design, catalyst/ionomer integration, operational variables, in situ diagnostics, and cell durability.
Rapid translation of catalysts from fundamental studies to high-performance devices could facilitate the process of developing and commercializing anion-exchange membrane fuel cells (AEMFCs). Traditionally, translation from material screening in three-electrode rotating disk electrode (RDE) cells to AEMFCs is complicated by differences in microenvironments, e.g. solid ionomer/membrane vs liquid electrolyte. Herein, we introduce a platform for translation to devices that utilizes ionomerless ultra-low-loading Ag-Pd alloy electrocatalyst cathodes synthesized by co-physical vapor deposition (PVD). Our ionomerless cathodes allow for systematic H 2 -O 2 AEMFC experiments while demonstrating comparable activity trends to those in three-electrode cells. Furthermore, here we show that our Ag 10 Pd 90 -based AEMFC reaches a peak power density of ~1 W cm$_{geo}^{-2}$ and ~10 W mg$_{PGM Cathode}^{-1}$ satisfying the U.S. Department of Energy’s platinum-group-metal (PGM) loading and cost targets. Our approach shows promise in facilitating the rapid translation between three-electrode studies and AEMFCs, offering a simple and effective design for decreasing PGM loadings.
One means of improving performance for electrochemical ammonia production through the Li-mediated N 2 reduction reaction (Li-NRR) is by cycling the current driving the reaction between open-circuit conditions and periods of applied current density. Herein, we have investigated the dynamics of the electrode–electrolyte interface under Li-NRR conditions during current cycling using in situ time-resolved neutron reflectometry and grazing-incidence synchrotron X-ray diffraction. During cycling, measured neutron reflectivity curves indicated bilayer formation in which Li-containing species such as LiOH, Li 2 O, and small quantities of Li 3 N and metallic Li primarily appeared in a thin layer at the cathode surface, above which formed a much larger, porous, ‘solid–electrolyte interface’ (SEI) layer. Upon return to open-circuit conditions, Li-containing species quickly moved out of the thin layer, leaving a compact, stable layer of decomposition products underneath the SEI layer. This SEI layer concomitantly filled with electrolyte or dissolved, becoming indistinguishable from the electrolyte via contrast in scattering-length density (SLD). During the second current cycle, Li-containing species again preferentially deposited directly atop the cathode, with the thick SEI-like layer again appearing within a minute. This SEI layer exhibited a lower SLD more quickly than in the first cycle, which might suggest that Li-containing species become distributed within the porous SEI layer. Furthermore, these time-resolved observations of SEI and plated layers during current cycling suggest that benefits associated with return to open-circuit conditions between periods of applied current density may be related to the concomitant loss of Li-containing species from a thin layer at the cathode surface into a porous SEI layer that becomes filled with electrolyte or dissolves.
Sustainable electricity generation via hydrogen fuel cells requires the development of efficient oxygen reduction reaction (ORR) catalysts. In situ/operando experiments are necessary to uncover the extent of dynamic material changes during catalysis. Herein, we use in situ/operando X-ray absorption near-edge spectroscopy to track Mn valence changes of a promising, ultrathin, porous MnO x layer on a Ag thin film. Mn–K-edge measurements as a function of electrochemical environment and ORR conditions reveal that, interestingly, when driving the ORR at 0.8 VRHE, the Mn is distinctively more reduced and the MnO x redox is nonreversible in contrast to measurements in N 2 -saturated electrolyte. Ex situ inductively coupled plasma mass spectrometry, atomic force microscopy, and X-ray photoelectron spectroscopy indicate that these phenomena do not correlate to metal dissolution but might be associated with morphological surface reconstruction related to Ag valency. Furthermore, this study highlights how the microenvironment and catalysis play a key role in the in situ/operando surface structure and chemical state.
The electrochemical oxidation of bio-derived molecules has recently garnered interest for its potential in opening electrified synthetic pathways toward value-added products. Herein, we investigate the electrochemical conversion of benzyl alcohol (BA) to benzaldehyde and benzoate on nickel–iron (Fe ~ 7–18%) electrodes as a model system to understand reaction mechanisms and environmental conditions that can transform these molecules. Our results indicate a strong correlation between benzyl alcohol oxidation (BAO) onset potentials and Ni(II/III) redox peak positions, highlighting the potential role that lower oxidation states of nickel, i.e., Ni 3+ , can play in BAO catalysis. Our work on the Ni 2+/3+ system complements mechanisms that involve higher oxidation states of Ni as reported by others. We note that the Ni redox position and thus BAO onset is impacted by Fe incorporation during electrochemistry from unpurified electrolytes, which can resemble standard reactor operating conditions. We perform a systematic computational investigation into BAO and provide density functional theory (DFT) insights into how the redox mechanism has been such a prominent focus of alcohol oxidations. This includes the mode of BA adsorption and the nature of the adsorption site; upon conversion of the Ni 2+ surface to active Ni 3+ via hydroxyl deprotonation, BAO is thermodynamically downhill. Our DFT study also introduces the possibility of a vacancy-driven mechanism, though expected to be less prevalent during catalysis than the redox mechanism for a Ni 3+ surface. Through the systematic investigation of experimental reaction conditions and computational free energy thermodynamics, we have gained valuable insights into BAO reaction mechanisms that inform catalytic activity. Our study opens avenues for further design and development of catalyst active sites for the oxidation of related organic molecules.
Abstract The shift towards cheaper, non‐platinum group metal electrocatalyst materials for clean energy technologies is coupled with challenges in maintaining long‐term performance. For practical purposes, electrocatalytic stability typically focuses on catalyst electrochemical performance over time. However, a deeper understanding of catalyst material property changes during operation is needed to enable material‐specific design strategies for long‐term stabilization. In the last several decades, improvements in material characterization techniques have made it possible to probe the composition, structure, and degradation products of catalysts in situ/operando. Herein we review the current understanding of in situ/operando material stability of Co‐based electrocatalysts for the oxygen evolution (OER) and reduction reactions (ORR) in acidic and alkaline environments. We focus on in situ/operando materials characterization of three categories of Co‐based OER/ORR catalysts: oxides and (oxy)hydroxides, mixed‐metal catalysts, and non‐oxide materials. This review aims to compile and compare the results from multiple studies and techniques to provide insight into the role that the starting material, pH, and applied potential have on the active surface and stability of Co‐based materials. We conclude by highlighting directions that have been underexplored with opportunities for continued research including improving in situ/operando characterization, methods to probe long‐term material changes, and the development of operando studies on full‐scale devices. Using Co‐based materials as a case study, this review shows the vital role that in situ/operando characterization must play in the future of improving electrocatalyst stability.
Herein, we utilize an on-line electrochemical flow cell coupled with an inductively coupled plasma-mass spectrometer (ICP-MS) to characterize the impact of composition and reactant gas on the multielement dissolution of Mn(-Cr)-Sb-O electrocatalysts. Compared to Mn 2 O 3 and Cr 2 O 3 oxides, we find that the antimonate framework stabilizes Mn at OER potentials and Cr at both ORR and OER potentials. Furthermore, dissolution of Mn and Cr from Mn(-Cr)-Sb-O is found to be driven by ORR reaction rate, with minimal dissolution under N 2 . We observe preferential dissolution of Cr totaling 13% over 10 minutes at 0.3, 0.6, and 0.9 V vs RHE, with only 1.5% loss of Mn, indicating an enrichment of Mn at the surface of the particles. Despite this asymmetric dissolution, in situ X-ray absorption spectroscopy (XAS) showed no measurable changes in the Mn K-edge at comparable potentials. This lack of change could suggest that modification to the Mn oxidation state in the surface layer is too small or that layer is too thin to be measured with the bulk XAS measurement. Lastly, on-line ICP-MS was used to assess the effects of applied potential, scan rate, and current of Mn-Cr-Sb-O during cyclic voltammetry and accelerated stress tests. With this deeper understanding of the interplay between oxygen reduction and dissolution, testing procedures were identified to maximize both activity and stability. This work highlights the use of multi-modal in situ characterization techniques in tandem to build a more complete model of stability and develop protocols for optimizing catalyst performance.
In this perspective, we highlight results of a research consortium devoted to advancing understanding of oxygen reduction reaction (ORR) catalysis as a means to inform fuel cell science. We demonstrate how targeted collaborations between different institutions from academic, national lab, and industry backgrounds and different scientific disciplines like theory, experiment, and characterization can yield unique insights into fuel cell catalysts. We comment on such insights into material designs for platinum-group-metal alloys, transition metal oxides, and non-traditional materials including metal–organic frameworks; systems that have served as the foundational building blocks for our consortium. We also motivate a renewed focus on catalyst durability in light of emerging technological requirements and paths forward in understanding in situ and operando electrochemical stability. Lastly, we describe new frontiers ORR research can take and how emerging artificial intelligence tools can assist researchers in capturing data, selecting new experiments, and guiding characterization to accelerate the design and discovery of fuel cell catalysts. A main goal of sharing this perspective is to discuss the rationale for our future research plans based on our consortium work. However, we also hope to illustrate both the potential impact of a collaborative strategy with the hopes of inspiring a higher degree of Industry-Academia-National Laboratory collaboration and encourage other centers and consortiums to distill and share their findings in a similar perspective-type article. Together we hope to enable the fuel cell research community to engage in a discussion of strategies for research and accelerated development of catalysts with improved activity and stability.
During chemical mechanical polishing (CMP) process optimization, a unique corrosion defect was identified in the tungsten (W) contact plugs, which were investigated to develop practical solutions to improve CMP mass productivity. The corrosion defect occurred in the absence of external incident energy and was observed to occur only at the W plugs connected to the P + /n-well close to the wafer edge. To examine the root cause of the corrosion, a series of experiments was carried out at each W CMP step, using in-line defect inspection. Additional experiments were conducted using on-line inductively coupled plasma mass spectrometry (ICP-MS) to understand pH- and potential-dependent electrochemical dissolution behaviors of W. Experimentally, W corrosion was confirmed to be exacerbated if the surface oxide of the W plugs is removed by the deionized water (DIW) rinsing step under wafer pressurization, then exposed to DIW and alkaline cleaning solution. Although the DIW rinsing step is commonly performed to clean polishing pads right after the main polishing, a small amount of applied pressure (0.5 psi) without slurry supply can lead to corrosion defects. Finally, this wear-induced corrosion of the W plugs can be prevented by removing the applied pressure during the post DIW rinsing step of W CMP.
The development of inexpensive and abundant catalysts with high activity, selectivity, and stability for the oxygen reduction reaction (ORR) is imperative for the widespread implementation of fuel cell devices. Herein, we present a combined theoretical–experimental approach to discover and design first-row transition metal antimonates as excellent electrocatalytic materials for the ORR. Theoretically, we identify first-row transition metal antimonates–MSb 2 O 6 , where M = Mn, Fe, Co, and Ni–as nonprecious metal catalysts with good oxygen binding energetics, conductivity, thermodynamic phase stability, and aqueous stability. Among the considered antimonates, MnSb 2 O 6 shows the highest theoretical ORR activity based on the 4e – ORR kinetic volcano. Experimentally, nanoparticulate transition metal antimonate catalysts are found to have a minimum of a 2.5-fold enhancement in intrinsic mass activity (on transition metal mass basis) relative to the corresponding transition metal oxide at 0.7 V vs RHE in 0.1 M KOH. MnSb 2 O 6 is the most active catalyst under these conditions, with a 3.5-fold enhancement on a per Mn mass activity basis and 25-fold enhancement on a surface area basis over its antimony-free counterpart. Electrocatalytic and material stability are demonstrated over a 5 h chronopotentiometry experiment in the stability window identified by theoretical Pourbaix analysis. Furthermore, this study further highlights the stable and electrically conductive antimonate structure as a framework to tune the activity and selectivity of nonprecious metal oxide active sites for ORR catalysis.
Understanding fundamental material–property relationships in mixed-element catalyst systems is crucial to advancing the viability of renewable electrochemical energy technologies, an important part of creating a more sustainable future. Herein, we report our insight on the nature and dynamics of highly active silver–manganese oxide (Ag–MnOx) catalyst surfaces for the oxygen reduction reaction (ORR) via a combined experimental–theoretical approach. Experimentally, we synthesize well-mixed Ag–Mn co-deposited thin films that are measurably flat and smooth, despite Mn surface migration and oxidation upon air exposure and electrochemical measurements. Cyclic voltammetry in 0.1 M KOH demonstrates up to 10-fold specific activity enhancements over pure Ag at 0.8 V vs. RHE for Ag-rich films (70–95% Ag in bulk). To further understand the Ag–Mn system, separate samples were synthesized with small amounts of Mn sequentially deposited onto the surface of a pure Ag thin film (Mn@Ag), ranging from partial to full surface coverage (down to 0.3 nm Mn $cm^{-2}_{geo}$ ~ 0.2 μg Mn $cm^{-2}_{geo}$). These sequentially deposited Mn@Ag films show analogous performance to their co-deposited counterparts indicating similar enhanced active sites. With density functional theory (DFT), we calculate that this enhancement arises from the tuned d-band of these material surfaces owing to the optimal hybridization of the electronic structures in specific Ag and MnO x geometries. Together, electrochemical measurements, DFT calculations, X-ray absorption spectroscopy, and valence-band X-ray photoelectron spectroscopy suggest synergistic electronic interactions between Ag and MnOx yield enhanced oxygen adsorption, and thus ORR activity, with DFT highlighting the Ag–MnO x interface sites as the most enhanced. This work demonstrates how combined experimental–theoretical methods can help design electrocatalysts with enhanced electrocatalytic properties and understand the nature of complex mixed metal–metal oxide surfaces.
Alloying is a powerful tool that can improve the electrocatalytic performance and viability of diverse electrochemical renewable energy technologies. Herein, we enhance the activity of Pd-based electrocatalysts via Ag-Pd alloying while simultaneously lowering precious metal content in a broad-range compositional study focusing on highly comparable Ag-Pd thin films synthesized systematically via electron-beam physical vapor co-deposition. Cyclic voltammetry in 0.1 M KOH shows enhancements across a wide range of alloys; even slight alloying with Ag (e.g. Ag 0.1 Pd 0.9 ) leads to intrinsic activity enhancements up to 5-fold at 0.9 V vs. RHE compared to pure Pd. Based on density functional theory and x-ray absorption, we hypothesize that these enhancements arise mainly from ligand effects that optimize adsorbate–metal binding energies with enhanced Ag-Pd hybridization. This work shows the versatility of coupled experimental-theoretical methods in designing materials with specific and tunable properties and aids the development of highly active electrocatalysts with decreased precious-metal content.
Rigorous in situ studies of electrocatalysts are required to enable the design of higher performing materials. Nonplatinum group metals for oxygen reduction reaction (ORR) catalysis containing light elements such as O, N, and C are known to be susceptible to both ex situ and in situ oxidation, leading to challenges associated with ex situ characterization methods. We have previously shown that the bulk O content plays an important role in the activity and selectivity of Mo–N catalysts, but further understanding of the role of composition and morphological changes at the surface is needed. Here, we report the measurement of in situ surface changes to a molybdenum nitride (MoN) thin film under ORR conditions using grazing incidence X-ray absorption and reflectivity. We show that the half-wave potential of MoN can be improved by ~90 mV by potential conditioning up to 0.8 V versus RHE. Utilizing electrochemical analysis, dissolution monitoring, and surface-sensitive X-ray techniques, we show that under moderate polarization (0.3–0.7 V vs RHE) there is local ligand distortion, O incorporation, and amorphization of the MoN surface, without changes in roughness. Furthermore, with a controlled potential hold procedure, we show that the surface changes concurrent with potential conditioning are stable under ORR relevant potentials. Conversely, at higher potentials (≥0.8 V vs RHE), the film incorporates O, dissolves, and roughens, suggesting that in this higher potential regime, the performance enhancements are due to increased access to active sites. Density functional theory calculations and Pourbaix analysis provide insights into film stability and O incorporation as a function of potential. These findings coupled with in situ electrochemical surface-sensitive X-ray techniques demonstrate an approach to studying nontraditional surfaces in which we can leverage our understanding of surface dynamics to improve performance with the rational, in situ tuning of active sites.