Engineering topics
Kreter, A.
Publications and source records attributed to Kreter, A..
Influence of heavier impurity deposition on surface morphology development and sputtering behavior explored in multiple linear plasma devices
Surface morphology development and sputtering behavior of Cr, as a test material, have been explored under He plasma exposure at a low incident ion energy of ~80 eV in multiple linear plasma devices: PISCES-A, PSI-2, and NAGDIS-II. From comparison of the experiments in these devices, deposition of a small amount of heavier impurities (Mo in NAGDIS-II and Ta in PISCES-A) onto Cr is found to result in the formation of cone structures on the Cr surface due to preferential sputtering, resulting in a significant reduction (up to ~10 times) in the sputtering yield of Cr due to line-of-sight redeposition onto the neighboring cones. The heavier impurities are thought to originate from a sample holding cap/cover, which can be sputtered by a trace amount of intrinsic impurities (C, O, etc) as well as by Cr ionized in the plasma. It can be concluded from the Cr experiments, as well as additional Be data collected in PISCES-B, that heavier impurity deposition plays a major role in the cone structure formation, while other mechanisms (e.g. surface irregularity and oxide) also exist.
Plasma exposures of a high-conductivity graphitic foam for plasma facing components
The plasma-surface interactions from samples of high-conductivity graphitic foam biased to 120 V and placed in 6–8 eV deuterium plasmas with densities as high as 10 19 m -3 were investigated at the PSI-2 linear plasma device in Jülich. Graphitic foam-plasma interactions were also studied at the Wendelstein 7-X (W7-X) stellarator in Greifswald by exposure to hydrogen and helium plasmas using the Jülich multi-purpose manipulator. The purpose was to explore the possibility of using the material in a plasma facing component, and initial results were encouraging. In W7-X, no measurable erosion or cracking was observed. The PSI-2 samples received a deuterium fluence of 5 × 10 25 m -2 resulting in an average erosion of 43 µm or about 5 mg per sample. Residual gas analysis (RGA) data were acquired to monitor sample outgassing. Laser-induced Breakdown Spectroscopy (LIBS) was used to measure deuterium retention in the porous foam. After exposure, the surfaces were characterized with scanning electron microscopy, energy dispersive x-ray analysis and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The graphitic foam has a thermal conductivity as high as 287 W/mK and is considered as a replacement to more exotic carbon fiber composites such as SepCarb NB31 or isotropic graphites like ATJ that are no longer produced but used in present-day tokamak experiments. Actively cooled monoblocks were made from the foam and underwent extensive materials characterization including infrared response studies at Oak Ridge National Laboratory. This material is under consideration for the proposed actively-cooled W7-X divertor scraper element.
Surface biasing influence on the physical sputtering in fusion devices
Explore the source record for details and available documents.
Note: Arc discharge plasma source with plane segmented LaB{sub 6} cathode
A plane cathode composed of close-packed hexagonal LaB{sub 6} (lanthanum hexaboride) segments is described. The 6 cm diameter circular cathode is heated by radiation from a graphite foil flat spiral. The cathode along with a hollow copper anode is used for the arc discharge plasma production in a newly developed linear plasma device. A separately powered coil located around the anode is used to change the magnetic field strength and geometry in the anode region. Different discharge regimes were realized using this coil.
Tritium trapping on the plasma irradiated tungsten surface
Tungsten (W) is a candidate material for plasma-facing high heat-flux structures in future fusion reactors. The aim of this study is to assess how reasonably one can predict the tritium inventory in actual fusion machines using data on the hydrogen isotope inventory obtained in laboratory experiments. W specimens previously exposed to deuterium (D) plasmas both in the TEXTOR tokamak and high flux linear plasma generator (LPG) were subsequently loaded with tritium at 573 K for 3 h. The retention of tritium in the near-surface W layer was examined by imaging plate technique. The study shows that on the TEXTOR-plasma-exposed W surface, tritium was mainly trapped in carbon deposits, and for LPG-plasma-exposed W specimens, tritium was trapped in defects created in the near-surface layer during the course of D plasma exposure.
RF physics of ICWC discharge at high cyclotron harmonics
Recent experiments on Ion Cyclotron Wall Conditioning (ICWC) performed in tokamaks TEXTOR and ASDEX Upgrade with standard ICRF antennas operated at fixed frequencies but variable toroidal magnetic field demonstrated rather contrasting parameters of ICWC discharge in scenarios with on-axis fundamental ion cyclotron resonance (ICR) for protons,ω=ω{sub H+}, and with its high cyclotron harmonics (HCH), ω=10ω{sub cH+}⋅ HCH scenario: very high antenna coupling to low density RF plasmas (P{sub pl}≈0.9P{sub RF-G}) and low energy Maxwellian distribution of CX hydrogen atoms with temperature T{sub H}≈350 eV. Fundamental ICR: lower antenna-plasma coupling efficiency (by factor of about 1.5 times) and generation of high energy non-Maxwellian CX hydrogen atoms (with local energy E{sub ⊥H} ≥1.0 keV). In the present paper, we analyze the obtained experimental results numerically using (i) newly developed 0-D transport code describing the process of plasma production with electron and ion collisional ionization in helium-hydrogen gas mixture and (ii) earlier developed 1-D Dispersion Relation Solver accounting for finite temperature effects and collision absorption mechanisms for all plasma species in addition to conventionally examined Landau/TTPM damping for electrons and cyclotron absorption for ions. The numerical study of plasma production in helium with minor hydrogen content in low and high toroidal magnetic fields is presented. The investigation of the excitation, conversion and absorption of plasma waves as function of B{sub T}-field suggests that only fast waves (FW) may give a crucial impact on antenna coupling and characteristics of the ICWC discharge using standard poloidally polarized ICRF antennas designed to couple RF power mainly to FW. The collisional (non-resonant) absorption by electrons and ions and IC absorption by resonant ions of minor concentration in low T{sub e} plasmas is studied at fundamental ICR and its high harmonics.
Modeling of Carbon Migration During JET Injection Experiments
JET has performed two dedicated carbon migration experiments on the final run day of separate campaigns (2001 and 2004) using {sup 13}CH{sub 4} methane injected into repeated discharges. The EDGE2D/NIMBUS code modelled the carbon migration in both experiments. This paper describes this modelling and identifies a number of important migration pathways: (1) deposition and erosion near the injection location, (2) migration through the main chamber SOL, (3) migration through the private flux region aided by E x B drifts, and (4) neutral migration originating near the strike points. In H-Mode, type I ELMs are calculated to influence the migration by enhancing erosion during the ELM peak and increasing the long-range migration immediately following the ELM. The erosion/re-deposition cycle along the outer target leads to a multistep migration of {sup 13}C towards the separatrix which is called 'walking'. This walking created carbon neutrals at the outer strike point and led to {sup 13}C deposition in the private flux region. Although several migration pathways have been identified, quantitative analyses are hindered by experimental uncertainty in divertor leakage, and the lack of measurements at locations such as gaps and shadowed regions.