Engineering topics

Kropp, J. L.

Publications and source records attributed to Kropp, J. L..

6 records

NASA NTRS1992

The Gas-Grain Simulation Facility (GGSF) for Space Station Freedom - Design concept

The GGSF is specifically designed to accommodate micro-g experiments that investigate long-term effects and interactions between submicron to centimeter size particles. The paper introduces the science disciplines and the type of experiments that are currently envisioned for the GGSF. The broad range of science and technology requirements are discussed, and the Space Station Freedom (SSF) accommodations, and available utilities are reviewed. Based on the requirements and the available accommodations, a facility conceptual design is outlined. The required subsystems are listed, and the rationale and considerations that lead to the selected approach, delineated. The present GGSF concept is that of a modular facility system comprising a flight rack and an array of fully compatible and interchangeable subsystems that are designed to meet a diverse set of science requirements. The modularity allows for future upgrade of various subsystems as technology evolves and for introduction of new modules to accommodate new or different experiments. These features are essential for a facility that is expected to be in service on board the SSF for 10 years or more.

Gat, N.↗

NASA NTRS1989

Droplet combustion drop tower tests using models of the space flight apparatus

An engineering model built for droplet combustion drop tower tests is described. The model was built using a design with mechanical and electrical assemblies of the same level of complexity as they will have in flight. The model was tested for functional operation and integrated into a 5-sec drop tower. Test data obtained to date are presented together with model and test cell diagrams.

Haggard, J. B.↗

NASA NTRS1989

Droplet combustion experiment drop tower tests using models of the space flight apparatus

The Droplet Combustion Experiment (DCE) is an experiment that is being developed to ultimately operate in the shuttle environment (middeck or Spacelab). The current experiment implementation is for use in the 2.2 or 5 sec drop towers at NASA Lewis Research Center. Initial results were reported in the 1986 symposium of this meeting. Since then significant progress was made in drop tower instrumentation. The 2.2 sec drop tower apparatus, a conceptual level model, was improved to give more reproducible performance as well as operate over a wider range of test conditions. Some very low velocity deployments of ignited droplets were observed. An engineering model was built at TRW. This model will be used in the 5 sec drop tower operation to obtain science data. In addition, it was built using the flight design except for changes to accommodate the drop tower requirements. The mechanical and electrical assemblies have the same level of complexity as they will have in flight. The model was tested for functional operation and then delivered to NASA Lewis. The model was then integrated into the 5 sec drop tower. The model is currently undergoing initial operational tests prior to starting the science tests.

Haggard, J. B.↗

NASA NTRS1986

Solar terrestrial and plasma processes experiments on space station

The currently planned utilization of the space station to perform investigations in solar terrestrial physics and plasma physics is outlined. The investigations and instrumentation planned for the Solar Terrestrial Observatory and its associated space station accommodation requirements are described. In addition, the planned placement of the Solar Terrestrial Observatory instruments are discussed along with typical operational scenarios. In the area of plasma physics, some preliminary plans for scientific investigations and for the accommodation of a plasma physics facility attached to the space station called the Plasma Processes Laboratory are outlined. These preliminary experiment concepts use the space environment around the space station as an unconfined plasma laboratory.

Roberts, W. T.↗

NASA NTRS1984

Preliminary design of two Space Shuttle fluid physics experiments

The mid-deck lockers of the STS and the requirements for operating an experiment in this region are described. The design of the surface tension induced convection and the free surface phenomenon experiments use a two locker volume with an experiment unique structure as a housing. A manual mode is developed for the Surface Tension Induced Convection experiment. The fluid is maintained in an accumulator pre-flight. To begin the experiment, a pressurized gas drives the fluid into the experiment container. The fluid is an inert silicone oil and the container material is selected to be comparable. A wound wire heater, located axisymmetrically above the fluid can deliver three wattages to a spot on the fluid surface. These wattages vary from 1-15 watts. Fluid flow is observed through the motion of particles in the fluid. A 5 mw He/Ne laser illuminates the container. Scattered light is recorded by a 35mm camera. The free surface phenomena experiment consists of a trapezoidal cell which is filled from the bottom. The fluid is photographed at high speed using a 35mm camera which incorporated the entire cell length in the field of view. The assembly can incorporate four cells in one flight. For each experiment, an electronics block diagram is provided. A control panel concept is given for the surface induced convection. Both experiments are within the mid-deck locker weight and c-g limits.

Gat, N.↗

NASA NTRS1983

Apparatus analysis and preliminary design of low gravity porous solids experiment for STS Orbiter mid-deck

The apparatus analysis laboratory equipment design and fabrication and the preliminary design of the Combustion of Porous Solids Experiment for operation in the mid-deck area of the Shuttle are described. The apparatus analysis indicated that the mid-deck region of the STS was a feasible region of the Shuttle for operation. A sixteen tube concept was developed with tubes of 75 cm length and up to 5.6 cm accommodated. The experiment is viewed by IR sensors and a 16 mm camera. Laboratory equipment was designed and fabricated to test the parible injection, mixing and venting concepts. This equipment was delivered to NASA/LeRC. A preliminary design was made for the experiment based upon the apparatus analysis. The design incorporated results from the Phase ""O'' Safety Review. This design utilizes a closed tube concept in which the particles are stored, injected and burned with no coupling to the Shuttle environment. Drawings of the major components and an assembly are given. The electronics are described for the experiment. An equipment list is presented and an experiment weight estimate is determined. The mission operation requirements are outlined.

Fleeter, R. D.↗