Engineering topics

Krotkov, Nickolay A.

Publications and source records attributed to Krotkov, Nickolay A..

At least 19 records

NASA NTRS2020

High-Resolution Mapping of SO2 Using Airborne Observations from the GeoTASO Instrument During the KORUS-AQ Field Study: PCA-Based Vertical Column Retrievals

The Geostationary Trace gas and Aerosol Sensor Optimization (GeoTASO) instrument is an airborne hyperspectral spectrometer measuring backscattered solar radiation in the ultraviolet (290–400 nm) and visible (415–695 nm) wavelength regions. This paper presents high-resolution sulfur dioxide (SO2) maps over the Korean Peninsula, produced by SO2 retrievals from GeoTASO measurements during the Korea–United States Air Quality Field Study (KORUS-AQ) from May to June 2016. The highly sensitive GeoTASO instrument with a spatial resolution of ~250 m × 250 m can detect point emission sources of SO2 within its fields of view, even without merging multiple overlapping observations. To retrieve SO2 vertical columns from the GeoTASO measurements, we apply an algorithm based on principal component analysis (PCA), which is effective in suppressing noise and biases in SO2 retrievals. The retrievals successfully capture SO2 plumes and various point sources such as power plants, a petrochemical complex, and a steel mill, located in South Chungcheong Province, some of which are not detected by a ground-based in situ measurement network. Spatial distributions of SO2 from GeoTASO observations in source areas are consistent with those from the Stack Tele-Monitoring System reports and airborne in situ SO2 measurements. Comparisons of SO2 retrievals from GeoTASO and existing satellite sensors demonstrate the significance of high-resolution SO2 observations, by indicating that GeoTASO detects small SO2 emission sources that are not precisely resolved by single overpasses of satellites. To assess future geostationary SO2 observations having a higher spatial resolution, we upscale the GeoTASO SO2 retrievals to a spatial resolution of the Geostationary Environment Monitoring Spectrometer (GEMS). Since the upscaled GeoTASO retrievals also detect SO2 plumes clearly, we expect from GEMS to identify even small SO2 emission sources over Asia.

Chong, Heesung↗

NASA NTRS2019

Chemical Climatology of Atmospheric Pollutants in the Eastern United States: Seasonal/Diurnal Cycles and Contrast Under Clear/Cloudy Conditions for Remote Sensing

We statistically assessed temporal variations of observed concentrations of eight atmospheric pollutants (SO2, NO, NO2, NO(y), O3, CO, NH3, and HNO3) at three urban sites and one rural site in the eastern United States for a ten-year period (4 years for NH3). Diurnal/seasonal patterns of observed mean concentrations and their decade-scale trends under different weather conditions were evaluated. Concentrations of pollutants decreased consistently during the observation period (as long as 1997–2013), although nighttime ozone during winter appears to increase because of reduced NO-O3 titration. This study shows that the decay time of major air pollutant concentrations such as SO2 and NO(x) can be short as a few hours to one day. We also identified substantial differences between the mean concentrations of pollutants at clear sky and overcast conditions that could introduce biases into satellite observations. Surface concentrations of SO2 and CO are distinctly higher under cloud free than under overcast conditions by ∼30% and ∼20% respectively. NO2 shows a complex pattern, but demonstrates lower daytime concentrations under cloud-free skies. All of these estimates are important for understanding the chemical climatology of these atmospheric pollutants, especially their diurnal/seasonal cycles under different weather conditions. For four-year measurements, NH3 shows a substantial difference, with clear sky observations roughly a factor of two higher than those under overcast conditions. To track changes in the future, the full daily cycle of atmospheric pollutants monitored by geostationary satellite such as the future TEMPO mission may better capture patterns and trends.

TEMPO↗

NASA NTRS2018

Investigation of NO2 Measurements Made During DISCOVER-AQ and KORUS-AQ Campaigns in Conjunction with NO2 Tropospheric Column from the Ozone Monitoring Instrument (OMI) and High-Resolution Community Multi-Scale Air Quality (CMAQ) Model Simulation

Atmospheric NO2 is produced by combustion, lightning, and in soil. NO2 affects ozone production and criteria pollutant itself.It also has indirect radiative impacts in the troposphere, since ozone has largest warming effect in upper troposphere. Tropospheric vertical column densities (VCD) of NO2 are available from satellites (GOME, OMI, SCIAMACHY, GOME-2). DISCOVER-AQ and KORUS-AQ aircraft campaigns we reconducted to improve the use of satellites to monitor air quality for public health and environmental benefit in United States and South Korea. In this study, we investigate 1) How do these measurements compare? 2) What is the best way to make comparisons of space- and ground-based measurements?

multi-scale air quality↗

NASA NTRS2018

A New Global Anthropogenic SO2 Emission Inventory for the Last Decade: A Mosaic of Satellite-Derived and Bottom-Up Emissions

Sulfur dioxide (SO2) measurements from the Ozone Monitoring Instrument (OMI) satellite sensor have been used to detect emissions from large point sources. Emissions from over 400 sources have been quantified individually based on OMI observations, accounting for about a half of total reported anthropogenic SO2 emissions. Here we report a newly developed emission inventory, OMI-HTAP, by combining these OMI-based emission estimates and the conventional bottom-up inventory, HTAP, for smaller sources that OMI is not able to detect. OMI-HTAP includes emissions from OMI-detected sources that are not captured in previous leading bottom-up inventories, enabling more accurate emission estimates for regions with such missing sources. In addition, our approach offers the possibility of rapid updates to emissions from large point sources that can be detected by satellites. Our methodology applied to OMI-HTAP can also be used to merge improved satellite-derived estimates with other multi-year bottom-up inventories, which may further improve the accuracy of the emission trends. OMI-HTAP SO2 emissions estimates for Persian Gulf, Mexico, and Russia are 59%, 65%, and 56% larger than HTAP estimates, respectively, in year 2010. We have evaluated the OMI-HTAP inventory by performing simulations with the Goddard Earth Observing System version 5 (GEOS-5) model. The GEOS-5 simulated SO2 concentrations driven by both HTAP and OMI-HTAP were compared against in situ measurements. We focus for the validation on year 2010 for which HTAP is most valid and for which a relatively large number of in situ measurements are available. Results show that the OMI-HTAP inventory improves the agreement between the model and observations, in particular over the US, with the normalized mean bias decreasing from 0.41 (HTAP) to -0.03 (OMI-HTAP) for year 2010. Simulations with the OMI-HTAP inventory capture the worldwide major trends of large anthropogenic SO2 emissions that are observed with OMI. Correlation coefficients of the observed and modelled surface SO2 in 2014 increase from 0.16 (HTAP) to 0.59 (OMI-HTAP) and the normalized mean bias dropped from 0.29 (HTAP) to 0.05 (OMI-HTAP), when we updated 2010 HTAP emissions with 2014 OMI-HTAP emissions in the model.

Sulfur dioxide (SO2)↗

NASA NTRS2018

A Cloud Algorithm Based on the O2-O2 477 nm Absorption Band Featuring an Advanced Spectral Fitting Method and the Use of Surface Geometry-Dependent Lambertian-Equivalent Reflectivity

We discuss a new cloud algorithm that retrieves an effective cloud pressure, also known as cloud optical centroid pressure (OCP), from oxygen dimer (O2-O2) absorption at 477nm after determining an effective cloud fraction (ECF) at 466nm, a wavelength not significantly affected by trace-gas absorption and rotational Raman scattering. The retrieved cloud products are intended for use as inputs to the operational nitrogen dioxide (NO2) retrieval algorithm for the Ozone Monitoring Instrument (OMI) flying on the Aura satellite. The cloud algorithm uses temperature-dependent O2-O2 cross sections and incorporates flexible spectral fitting techniques that account for specifics of the surface reflectivity. The fitting procedure derives O2-O2 slant column densities (SCDs) from radiances after O3, NO2, and H2O absorption features have been removed based on estimates of the amounts of these species from independent OMI algorithms. The cloud algorithm is based on the frequently used mixed Lambertian-equivalent reflectivity (MLER) concept. A geometry-dependent Lambertian-equivalent reflectivity (GLER), which is a proxy of surface bidirectional reflectance, is used for the ground reflectivity in our implementation of the MLER approach. The OCP is derived from a match of the measured O2-O2 SCD to that calculated with the MLER method. Temperature profiles needed for computation of vertical column densities are taken from the Global Modeling Initiative (GMI) model. We investigate the effect of using GLER instead of climatological LER on the retrieved ECF and OCP. For evaluation purposes, the retrieved ECFs and OCPs are compared with those from the operational OMI cloud product, which is also based on the same O2-O2 absorption band. Impacts of the application of the newly developed cloud algorithm to the OMI NO2 retrieval are discussed.

cloud fraction and pressure↗

NASA NTRS2018

Comparisons of Spectral Aerosol Single Scattering Albedo in Seoul, South Korea

Quantifying aerosol absorption at ultraviolet (UV) wavelengths is important for monitoring air pollution and aerosol amounts using current (e.g., Aura/OMI (Ozone Monitoring Instrument)) and future (e.g., TROPOMI (TROPOspheric Monitoring Instrument), TEMPO (Tropospheric Emissions: Monitoring of POllution), GEMS (Geostationary Environment Monitoring Spectrometer) and Sentinel-4) satellite measurements. Measurements of column average atmospheric aerosol single scattering albedo (SSA) are performed on the ground by the NASA AERONET (AEROsol robotic NETwork) in the visible (VIS) and near-infrared (NIR) wavelengths and in the UV-VIS-NIR by the SKYNET (SKY radiometer NETwork) networks. Previous comparison studies have focused on VIS and NIR wavelengths due to the lack of co-incident measurements of aerosol and gaseous absorption properties in the UV. This study compares the SKYNET-retrieved SSA in the UV with the SSA derived from a combination of AERONET, MFRSR (MultiFilter Rotating Shadowband Radiometer), and Pandora (AMP) retrievals in Seoul, South Korea, in spring and summer 2016. The results show that the spectrally invariant surface albedo assumed in the SKYNET SSA retrievals leads to underestimated SSA compared to AMP values at near UV wavelengths. Re-processed SKYNET inversions using spectrally varying surface albedo, consistent with the AERONET retrieval improve agreement with AMP SSA. The combined AMP inversions allow for separating aerosol and gaseous (NO2 and O3) absorption and provide aerosol retrievals from the shortest UVB (305 nanometers) through VIS to NIR wavelengths (870 nanometers).

aerosol and gaseous absorption properties↗

NASA NTRS2017

Progress Report on the Airborne Composition Standard Variable Name and Time Series Working Groups of the 2017 ESDSWG

The role of NASA's Earth Science Data Systems Working Groups (ESDSWG) is to make recommendations relevant to NASA's Earth science data systems from users' experiences and community insight. Each group works independently, focusing on a unique topic. Progress of two of the 2017 Working Groups will be presented. In a single airborne field campaign, there can be several different instruments and techniques that measure the same parameter on one or more aircraft platforms. Many of these same parameters are measured during different airborne campaigns using similar or different instruments and techniques. The Airborne Composition Standard Variable Name Working Group is working to create a list of variable standard names that can be used across all airborne field campaigns in order to assist in the transition to the ICARTT Version 2.0 file format. The overall goal is to enhance the usability of ICARTT files and the search ability of airborne field campaign data. The Time Series Working Group (TSWG) is a continuation of the 2015 and 2016 Time Series Working Groups. In 2015, we started TSWG with the intention of exploring the new OGC (Open Geospatial Consortium) WaterML 2 standards as a means for encoding point-based time series data from NASA satellites. In this working group, we realized that WaterML 2 might not be the best solution for this type of data, for a number of reasons. Our discussion with experts from other agencies, who have worked on similar issues, identified several challenges that we would need to address. As a result, we made the recommendation to study the new TimeseriesML 1.0 standard of OGC as a potential NASA time series standard. The 2016 TSWG examined closely the TimeseriesML 1.0 and, in coordination with the OGC TimeseriesML Standards Working Group, identified certain gaps in TimeseriesML 1.0 that would need to be addressed for the standard to be applicable to NASA time series data. An engineering report was drafted based on the OGC Engineering Report template, describing recommended changes to TimeseriesML 1.0, in the form of use cases. In 2017, we are conducting interoperability experiments to implement the use cases and demonstrate the feasibility and suitability of these modifications for NASA and related user communities. The results will be incorporated into the existing draft engineering report.

OGC (Open Geospatial Consortium) WaterML 2 standar↗

NASA NTRS2017

The Version 3 OMI NO2 Standard Product

We describe the new version 3.0 NASA Ozone Monitoring Instrument (OMI) standard nitrogen dioxide (NO2) products (SPv3). The products and documentation are publicly available from the NASA Goddard Earth Sciences Data and Information Services Center (https://disc.gsfc.nasa.gov/datasets/OMNO2_V003/summary/). The major improvements include (1) a new spectral fitting algorithm for NO2 slant column density (SCD) retrieval and (2) higher-resolution (1° latitude and 1.25° longitude) a priori NO2 and temperature profiles from the Global Modeling Initiative (GMI) chemistry–transport model with yearly varying emissions to calculate air mass factors (AMFs) required to convert SCDs into vertical column densities (VCDs). The new SCDs are systematically lower (by ∼10-40%) than previous, version 2, estimates. Most of this reduction in SCDs is propagated into stratospheric VCDs. Tropospheric NO2 VCDs are also reduced over polluted areas, especially over western Europe, the eastern US, and eastern China. Initial evaluation over unpolluted areas shows that the new SPv3 products agree better with independent satellite- and ground-based Fourier transform infrared (FTIR) measurements. However, further evaluation of tropospheric VCDs is needed over polluted areas, where the increased spatial resolution and more refined AMF estimates may lead to better characterization of pollution hot spots.

Ozone Monitoring Instrument (OMI)↗

NASA NTRS2017

Continuation of Long-Term Global SO2 Pollution Monitoring from OMI to OMPS

Over the past 20 years, advances in satellite remote sensing of pollution-relevant species have made space-borne observations an increasingly important part of atmospheric chemistry research and air quality management. This progress has been facilitated by advanced UV-vis spectrometers, such as the Ozone Monitoring Instrument (OMI) on board the NASA Earth Observing System (EOS) Aura satellite, and continues with new instruments, such as the Ozone Mapping and Profiler Suite (OMPS) on board the NASA-NOAA Suomi National Polar-orbiting Partnership (SNPP) satellite. In this study, we demonstrate that it is possible, using our state-of-the-art principal component analysis (PCA) retrieval technique, to continue the long-term global SO2 pollution monitoring started by OMI with the current and future OMPS instruments that will fly on the NOAA Joint Polar Satellite System (JPSS) 1, 2, 3, and 4 satellites in addition to SNPP, with a very good consistency of retrievals from these instruments. Since OMI SO2 data have been primarily used for (1) providing regional context on air pollution and long-range transport on a daily basis and (2) providing information on point emission sources on an annual basis after data averaging, we focused on these two aspects in our OMI-OMPS comparisons. Four years of retrievals (2012-2015) have been compared for three regions: eastern China, Mexico, and South Africa. In general, the comparisons show relatively high correlations (r = 0. 79-0.96) of daily regional averaged SO2 mass between the two instruments and near-unity regression slopes (0.76-0.97). The annual averaged SO2 loading differences between OMI and OMPS are small (< 0.03 Dobson unit (DU) over South Africa and up to 0.1 DU over eastern China). We also found a very good correlation (r = 0. 92-0.97) in the spatial distribution of annual averaged SO2 between OMI and OMPS over the three regions during 2012-2015. The emissions from ∼ 400 SO2 sources calculated with the two instruments also show a very good correlation (r = ∼ 0.9) in each year during 2012-2015. OMPS-detected SO2 point source emissions are slightly lower than those from OMI, but OMI-OMPS differences decrease with increasing strength of source. The OMI-OMPS SO2 mass differences on a pixel by pixel (daily) basis in each region can show substantial differences. The two instruments have a spatial correlation coefficient of 0.7 or better on < ∼ 50 % of the days. It is worth noting that consistent SO2 retrievals were achieved without any explicit adjustments to OMI or OMPS radiance data and that the retrieval agreement may be further improved by introducing a more comprehensive Jacobian lookup table than is currently used.

satellite remote sensing of pollution↗

NASA NTRS2017

The Net Decay Time of Anomalies in Concentrations of Atmospheric Pollutants

This paper introduces a new parameter to characterize the random component in temporal variability of atmospheric pollutants and proposes a simple statistical technique for its evaluation. That parameter is the net decay time (or the time scale) of the local anomalies in concentrations of atmospheric pollutants, rather than the traditionally used chemical lifetimes of total amounts of the species. Using widely available data of hourly multi-year surface trace gas pollutant concentrations we demonstrate a simplified way to estimate the net decay time with an exponential approximation of lag-correlation functions. We assessed the decay times of fluctuations in observations of eight atmospheric pollutants (SO2, NO, NO2, NOy, O3, CO, NH3, and HNO3) at two urban sites and one cleaner rural site in the Eastern US. The time scales of temporal fluctuations (net decay times) vary from about one hour to slightly more than one day. These scales are generally much shorter in urban environments than in remote regions. We also compared day- and night-time observations in warm and cold seasons. At night in the cold season, time scales of fluctuations in atmospheric pollutants are usually the longest. Such estimates should be useful to air quality prediction, public health, and satellite remote sensing research communities.

air quality prediction↗

NASA NTRS2017

New-Generation NASA Aura Ozone Monitoring Instrument (OMI) Volcanic SO2 Dataset: Algorithm Description, Initial Results, and Continuation with the Suomi-NPP Ozone Mapping and Profiler Suite (OMPS)

Since the fall of 2004, the Ozone Monitoring Instrument (OMI) has been providing global monitoring of volcanic SO2 emissions, helping to understand their climate impacts and to mitigate aviation hazards. Here we introduce a new-generation OMI volcanic SO2 dataset based on a principal component analysis (PCA) retrieval technique. To reduce retrieval noise and artifacts as seen in the current operational linear fit (LF) algorithm, the new algorithm, OMSO2VOLCANO, uses characteristic features extracted directly from OMI radiances in the spectral fitting, thereby helping to minimize interferences from various geophysical processes (e.g., O3 absorption) and measurement details (e.g., wavelength shift). To solve the problem of low bias for large SO2 total columns in the LF product, the OMSO2VOLCANO algorithm employs a table lookup approach to estimate SO2 Jacobians (i.e., the instrument sensitivity to a perturbation in the SO2 column amount) and iteratively adjusts the spectral fitting window to exclude shorter wavelengths where the SO2 absorption signals are saturated. To first order, the effects of clouds and aerosols are accounted for using a simple Lambertian equivalent reflectivity approach. As with the LF algorithm, OMSO2VOLCANO provides total column retrievals based on a set of predefined SO2 profiles from the lower troposphere to the lower stratosphere, including a new profile peaked at 13 km for plumes in the upper troposphere. Examples given in this study indicate that the new dataset shows significant improvement over the LF product, with at least 50% reduction in retrieval noise over the remote Pacific. For large eruptions such as Kasatochi in 2008 (approximately 1700 kt total SO2/ and Sierra Negra in 2005 (greater than 1100DU maximum SO2), OMSO2VOLCANO generally agrees well with other algorithms that also utilize the full spectral content of satellite measurements, while the LF algorithm tends to underestimate SO2. We also demonstrate that, despite the coarser spatial and spectral resolution of the Suomi National Polar-orbiting Partnership (Suomi-NPP) Ozone Mapping and Profiler Suite (OMPS) instrument, application of the new PCA algorithm to OMPS data produces highly consistent retrievals between OMI and OMPS. The new PCA algorithm is therefore capable of continuing the volcanic SO2 data record well into the future using current and future hyperspectral UV satellite instruments.

OMI↗

NASA NTRS2016

Impacts of Brown Carbon from Biomass Burning on Surface UV and Ozone Photochemistry in the Amazon Basin

The spectral dependence of light absorption by atmospheric particulate matter has major implications for air quality and climate forcing, but remains uncertain especially in tropical areas with extensive biomass burning. In the September-October 2007 biomass-burning season in Santa Cruz, Bolivia, we studied light absorbing (chromophoric) organic or brown carbon (BrC) with surface and space-based remote sensing. We found that BrC has negligible absorption at visible wavelengths, but significant absorption and strong spectral dependence at UV wavelengths. Using the ground-based inversion of column effective imaginary refractive index in the range 305368nm, we quantified a strong spectral dependence of absorption by BrC in the UV and diminished ultraviolet B (UV-B) radiation reaching the surface. Reduced UV-B means less erythema, plant damage, and slower photolysis rates. We use a photochemical box model to show that relative to black carbon (BC) alone, the combined optical properties of BrC and BC slow the net rate of production of ozone by up to 18 and lead to reduced concentrations of radicals OH, HO2, and RO2 by up to 17, 15, and 14, respectively. The optical properties of BrC aerosol change in subtle ways the generally adverse effects of smoke from biomass burning.

UV absorption OMI↗

NASA NTRS2016

Limb-Nadir Matching Using Non-Coincident NO2 Observations: Proof of Concept and the OMI-minus-OSIRIS Prototype Product

A variant of the limb-nadir matching technique for deriving tropospheric NO2 columns is presented in which the stratospheric component of the NO2 slant column density (SCD) measured by the Ozone Monitoring Instrument (OMI) is removed using non-coincident profiles from the Optical Spectrograph and InfraRed Imaging System (OSIRIS). In order to correct their mismatch in local time and the diurnal variation of stratospheric NO2, OSIRIS profiles, which were measured just after sunrise, were mapped to the local time of OMI observations using a photochemical boxmodel. Following the profile time adjustment, OSIRIS NO2 stratospheric vertical column densities (VCDs) were calculated. For profiles that did not reach down to the tropopause, VCDs were adjusted using the photochemical model. Using air mass factors from the OMI Standard Product (SP), a new tropospheric NO2 VCD product - referred to as OMI-minus-OSIRIS (OmO) - was generated through limb-nadir matching. To accomplish this, the OMI total SCDs were scaled using correction factors derived from the next-generation SCDs that improve upon the spectral fitting used for the current operational products. One year, 2008, of OmO was generated for 60 deg S to 60 deg N and a cursory evaluation was performed. The OmO product was found to capture the main features of tropospheric NO2, including a background value of about 0.3 x 10(exp 15) molecules per sq cm over the tropical Pacific and values comparable to the OMI operational products over anthropogenic source areas. While additional study is required, these results suggest that a limb-nadir matching approach is feasible for the removal of stratospheric NO2 measured by a polar orbiter from a nadir-viewing instrument in a geostationary orbit such as Tropospheric Emissions: Monitoring of Pollution (TEMPO) or Sentinel-4.

Photochemical Boxmodel↗

NASA NTRS2016

Aura OMI Observations of Regional SO2 and NO2 Pollution Changes from 2005 to 2015

The Ozone Monitoring Instrument (OMI) onboard NASA's Aura satellite has been providing global observations of the ozone layer and key atmospheric pollutant gases, such as nitrogen dioxide (NO2) and sulfur dioxide (SO2), since October 2004. The data products from the same instrument provide consistent spatial and temporal coverage and permit the study of anthropogenic and natural emissions on local-to-global scales. In this paper, we examine changes in SO2 and NO2 over some of the world's most polluted industrialized regions during the first decade of OMI observations. In terms of regional pollution changes, we see both upward and downward trends, sometimes in opposite directions for NO2 and SO2, for different study areas. The trends are, for the most part, associated with economic and/or technological changes in energy use, as well as regional regulatory policies. Over the eastern US, both NO2 and SO2 levels decreased dramatically from 2005 to 2015, by more than 40 and 80 percent, respectively, as a result of both technological improvements and stricter regulations of emissions. OMI confirmed large reductions in SO2 over eastern Europe's largest coal-fired power plants after installation of flue gas desulfurization devices. The North China Plain has the world's most severe SO2 pollution, but a decreasing trend has been observed since 2011, with about a 50 percent reduction in 2012-2015, due to an economic slowdown and government efforts to restrain emissions from the power and industrial sectors. In contrast, India's SO2 and NO2 levels from coal power plants and smelters are growing at a fast pace, increasing by more than 100 and 50 percent, respectively, from 2005 to 2015. Several SO2 hot spots observed over the Persian Gulf are probably related to oil and gas operations and indicate a possible underestimation of emissions from these sources in bottom-up emission inventories. Overall, OMI observations have proved valuable in documenting rapid changes in air quality over different parts of the world during last decade. The baseline established during the first 11 years of OMI is indispensable for the interpretation of air quality measurements from current and future satellite atmospheric composition missions.

SO2 and NO2↗

NASA NTRS2016

Aura OMI observations of regional SO2 and NO2 pollution changes from 2005 to 2015

The Ozone Monitoring Instrument (OMI) onboard NASA's Aura satellite has been providing global observations of the ozone layer and key atmospheric pollutant gases, such as nitrogen dioxide (NO2/ and sulfur dioxide (SO2/, since October 2004. The data products from the same instrument provide consistent spatial and temporal coverage and permit the study of anthropogenic and natural emissions on local-to-global scales. In this paper, we examine changes in SO2 and NO2 over some of the world's most polluted industrialized regions during the first decade of OMI observations. In terms of regional pollution changes, we see both upward and downward trends, sometimes in opposite directions for NO2 and SO2, for different study areas. The trends are, for the most part, associated with economic and/or technological changes in energy use, as well as regional regulatory policies. Over the eastern US, both NO2 and SO2 levels decreased dramatically from 2005 to 2015, by more than 40 and 80 %, respectively, as a result of both technological improvements and stricter regulations of emissions. OMI confirmed large reductions in SO2 over eastern Europe's largest coal-fired power plants after installation of flue gas desulfurization devices. The North China Plain has the world's most severe SO2 pollution, but a decreasing trend has been observed since 2011, with about a 50% reduction in 2012- 2015, due to an economic slowdown and government efforts to restrain emissions from the power and industrial sectors. In contrast, India's SO2 and NO2 levels from coal power plants and smelters are growing at a fast pace, increasing by more than 100 and 50 %, respectively, from 2005 to 2015. Several SO2 hot spots observed over the Persian Gulf are probably related to oil and gas operations and indicate a possible underestimation of emissions from these sources in bottom-up emission inventories. Overall, OMI observations have proved valuable in documenting rapid changes in air quality over different parts of the world during last decade. The baseline established during the first 11 years of OMI is indispensable for the interpretation of air quality measurements from current and future satellite atmospheric composition missions.

Pollution trends↗

NASA NTRS2015

A Decade of Change in NO2 and SO2 over the Canadian Oil Sands As Seen from Space

A decade (20052014) of observations from the Ozone Monitoring Instrument (OMI) were used to examine trends in nitrogen dioxide(NO2) and sulfur dioxide (SO2) over a large region of western Canada and the northern United States, with a focus on the Canadian oil sands. In the oil sands, primarily over an area of intensive surface mining, NO2 tropospheric vertical column densities (VCDs) are seen to be increasing by as much as 10year, with the location of the largest trends in a newly developing NO2 lobe well removed from surface monitoring stations. SO2 VCDs in the oil sands have remained approximately constant. The only other significant increase in the region was seen in NO2 over Bakken gas fields in North Dakota which showed increases of up to5yr. By contrast, other locations in the region show substantial declines in both pollutants, providing strong evidence to the efficacy of environmental pollution control measures implemented by both nations. The OMI-derived trends were found to be consistent with those from the Canadian surface monitoring network, although in the case of SO2, it was necessary to apply a correction in order to remove the residual signal from volcanic eruptions present in the OMI data.

NO2↗

NASA NTRS2014

Next Generation Aura-OMI SO2 Retrieval Algorithm: Introduction and Implementation Status

We introduce our next generation algorithm to retrieve SO2 using radiance measurements from the Aura Ozone Monitoring Instrument (OMI). We employ a principal component analysis technique to analyze OMI radiance spectral in 310.5-340 nm acquired over regions with no significant SO2. The resulting principal components (PCs) capture radiance variability caused by both physical processes (e.g., Rayleigh and Raman scattering, and ozone absorption) and measurement artifacts, enabling us to account for these various interferences in SO2 retrievals. By fitting these PCs along with SO2 Jacobians calculated with a radiative transfer model to OMI-measured radiance spectra, we directly estimate SO2 vertical column density in one step. As compared with the previous generation operational OMSO2 PBL (Planetary Boundary Layer) SO2 product, our new algorithm greatly reduces unphysical biases and decreases the noise by a factor of two, providing greater sensitivity to anthropogenic emissions. The new algorithm is fast, eliminates the need for instrument-specific radiance correction schemes, and can be easily adapted to other sensors. These attributes make it a promising technique for producing long-term, consistent SO2 records for air quality and climate research. We have operationally implemented this new algorithm on OMI SIPS for producing the new generation standard OMI SO2 products.

Sulfur dioxide↗

NASA NTRS2014

The Efficacy of Air Pollution Control Efforts: Evidence from AURA

Observations of NO2, SO2, and H2CO from OMI on AURA provide an excellent record of pollutant concentrations for the past decade. Abatement strategies to control criteria pollutants including ozone and fine particulate matter (PM2.5) have met with varying degrees of success. Sulfur controls had a profound impact on local SO2 concentrations and a measurable impact on PM2.5. Although substantial effort has gone into VOC control, ozone in the eastern US has responded dramatically to NOx emissions controls.

efficacy of air pollution↗