Search NASA⌕ Search

Engineering topics

Krousky, E

Publications and source records attributed to Krousky, E.

At least 19 records

Laser-produced aluminum plasma expansion inside a plastic plasma envelope

Previous experimental results demonstrated that the plasma pressure decreases with the growing atomic number of the target material. In this context, a question arose if the Al plasma outflow could be collimated using the plastic plasma as a compressor. To solve this problem, an experiment using a plastic target with an Al cylindrical insert was performed. The focal spot diameter substantially larger than that of the insert ensured simultaneous heating both target materials. This experiment proved that a production of Al plasma jets collimated by an action of outer plastic plasma is feasible [Kasperczuk et al., Laser Part. Beams 30, 1 (2012)]. The results of investigations presented here provide additional information on distributions of electron temperature in the outflowing plasma and time and space characteristics of ion emission, both registered at bare and constrained-flow Al targets. The experiment was carried out at the Prague asterix laser system iodine laser facility. The laser provided a 250 ps (full width at half maximum) pulse with the energy of 130 J at the third harmonic frequency ({lambda}{sub 3} = 0.438 {mu}m). A plastic target with an Al cylindrical insert of 400 {mu}m in diameter as well as a bare Al target (for comparison) was used. The focal spot diameter ({Phi}{sub L}) 1200 {mu}m ensured the lateral pressure effect of the plastic plasma strong enough to guarantee the effective Al plasma compression. The electron temperature measurements have shown that such Al plasma compression is accompanied by the increase of its temperature, dominance of which starts at distance of 0.5 mm from the target surface. Measurements of ion emission characteristics confirm the earlier numerical simulation prediction that in these conditions the plasma expansion geometry is closer to planar. The constrained Al plasma jet is very narrow and its axial velocity is considerably larger than the velocity of freely expanding Al plasma stream. It means that the plastic plasma envelope, besides the Al plasma compression, also strongly accelerates the Al plasma in its axial motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Highly efficient accelerator of dense matter using laser-induced cavity pressure acceleration

Acceleration of dense matter to high velocities is of high importance for high energy density physics, inertial confinement fusion, or space research. The acceleration schemes employed so far are capable of accelerating dense microprojectiles to velocities approaching 1000 km/s; however, the energetic efficiency of acceleration is low. Here, we propose and demonstrate a highly efficient scheme of acceleration of dense matter in which a projectile placed in a cavity is irradiated by a laser beam introduced into the cavity through a hole and then accelerated in a guiding channel by the pressure of a hot plasma produced in the cavity by the laser beam or by the photon pressure of the ultra-intense laser radiation trapped in the cavity. We show that the acceleration efficiency in this scheme can be much higher than that achieved so far and that sub-relativisitic projectile velocities are feasible in the radiation pressure regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Shot-to-shot reproducibility in the emission of fast highly charged metal ions from a laser ion source

The generation of fast highly charged metal ions with the use of the sub-nanosecond Prague Asterix Laser System, operated at a fundamental wavelength of 1315 nm, is reported. Particular attention is paid to shot-to-shot reproducibility in the ion emission. Au and Pd targets were exposed to intensities up to 5 x 10{sup 16} W/cm{sup 2}. Above the laser intensity threshold of {approx}3 x 10{sup 14} W/cm{sup 2} the plasma is generated in a form of irregular bursts. The maximum energy of protons constituting the leading edge of the fastest burst reaches a value up to 1 MeV. The fast ions in the following bursts have energy gradually decreasing with the increasing burst number, namely, from a value of about 0.5 MeV/charge regardless of the atomic number and mass of the ionized species.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma-wall interaction studies with optimized laser-produced jets

The production of the laser-produced plasma jets at burnt-through low-Z foils was optimized by using three-frame interferometry. When striking secondary targets, these jets of energetic particles represent an efficient tool for the investigation of transient phenomena at surfaces of the plasma-exposed solids. Two sets of precisely measured x-ray spectroscopic data demonstrate diagnostic potential of the collimated jets in the plasma-wall interaction studies: Blue Doppler shifts of the Al jet self-emission visualize ion deceleration in the near-wall region. Local depressions found in Al Ly{gamma} profiles emitted from Al/Si(PMMA) targets indicate charge exchange between the Al XIII and fully stripped C ions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interaction of Cu and plastic plasmas as a method of forming laser produced Cu plasma streams with a narrow jet or pipe geometry

This brief communication is aimed at investigations of interaction of axially symmetrical light (plastic) plasma with heavy (copper) plasma. The use of axially symmetrical target compositions consisting of materials with low and high atomic numbers makes it possible to create different plasma stream configurations (e.g., very narrow jet or pipe). In the paper certain their applications are suggested.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Influence of low atomic number plasma component on the formation of laser-produced plasma jets

The results of investigations are presented that are connected with a very simple method of plasma jet formation, which consists in irradiating a massive planar target made of material with relatively high atomic number by a partly defocused laser beam. This brief communication is aimed at investigations of interaction of axially symmetrical light (plastic-CH) plasma with heavy (copper) plasma. It demonstrates that a relatively thin plastic plasma envelope can compress the Cu plasma and control the Cu-jet formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental evidence of multimaterial jet formation with lasers

Laser-produced multimaterial jets have been investigated at the Prague Asterix Laser System laser [K. Jungwirth et al., Phys. Plasmas 8, 2495 (2001)]. The method of jet production is based on the laser-plasma ablation process and proved to be easy to set up and robust. The possibility of multimaterial laboratory jet production is demonstrated and complex hydrodynamic flows in the jet body are obtained. Two complementary diagnostics in the optical ray and x-ray ranges provide detailed information about jet characteristics. The latter are in agreement with estimates and two-dimensional radiation hydrodynamic simulation results. The experiment provides a proof of principle that a velocity field could be produced and controlled in the jet body. It opens a possibility of astrophysical jet structure modeling in laboratory.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Emission Characteristics and Stability of Laser Ion Sources

A new classification of laser ion sources concerning their pulse-to-pulse reproducibility in the ion emission is proposed. In particular, we distinguish between plasmas according to the electron distribution changing its characteristics at a laser intensity threshold of 10{sup 14} W/cm{sup 2}. Well reproducible continuous pulsed ion currents are typical for the intensity below the threshold. In contrast to this plasma the 'two-temperature' plasma arising for the intensity above this threshold shows not only a separation of charges in space and time but it also shows irregular and intense outbursts of ions similar to a self pulsing instability leading to a chaos. The sequence of fast ion outbursts visible on time-of-flight spectra is sensitive to details of non-linear interaction of the sub-nanosecond laser beam with the generated plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Highly efficient acceleration and collimation of high-density plasma using laser-induced cavity pressure

An efficient scheme of acceleration and collimation of dense plasma is proposed and examined. In the scheme, a target placed in a cavity coupled with a guiding channel is irradiated by a laser beam introduced into the cavity through a hole and accelerated along the channel by the pressure of the ablating plasma confined in the cavity. Using 1.315 mum, 0.3 ns laser pulse of energy up to 200 J and a thin CH target, it was shown that the energetic efficiency of acceleration in this scheme is an order of magnitude higher than in the case of conventional ablative acceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of the highest acceleration gradient for ions produced with a long laser pulse

Ultrafast plasma light ion streams have been produced using the 300 ps, kJ-class iodine laser, operating at PALS Centre in Prague. Ion detection was performed through standard ion collectors (IC) in time-of-flight configuration (TOF), shielded by thin metallic absorbers. This new diagnostics technique has been theoretically studied and experimentally tested in order to cut the long photopeak contribution and to analyze the ultrafast particle signal. Processing the obtained experimental IC-TOF data, including deconvolution processes of the TOF signals, UV/soft-x-ray photopeak absorption, and ion transmission calculations for different metallic filters, is shown. Mainly amorphous carbon (graphite) targets have been irradiated in order to limit the maximum number of ion charge states and to focus our study on demonstrating the validity of the proposed investigation technique. Maximum ion energy and acceleration gradient estimations as a function of the laser energy and focal spot diameter are reported.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Generation of high currents of carbon ions with the use of subnanosecond near-infrared laser pulses

Emission of carbon currents reaching values up to 2 A/cm{sup 2} at a distance of 1 m from the laser ion source driven by the subnanosecond Prague Asterix Laser System operated at a fundamental wavelength of 1315 nm is reported. Graphite targets were exposed to intensities up to 5x10{sup 16} W/cm{sup 2} varying both the laser energy and the position of the laser beam focus with respect to the target surface. The maximum energy gain of carbon ions was {approx_equal}1 MeV/u. At high laser intensities the shape of time-of-flight spectra is also formed by plasma outbursts, whose growth correlates with the oscillatory self-focusing of the laser beam.

43 PARTICLE ACCELERATORS↗

Cavity pressure acceleration: An efficient laser-based method of production of high-velocity macroparticles

We propose an efficient method of accelerating macroparticles to high velocities, which employs pressure of the plasma produced by a focused pulsed high-power laser beam inside a cavity-type target. That is why we have called it the cavity pressure acceleration (CPA) scheme. The method was tested during our experiments at the Prague Asterix Laser System, the results of which are reported here. They show that CPA makes it possible to accelerate both light and heavy macroparticles in arbitrary direction, with the acceleration efficiency far exceeding that achieved upto now by using the classic ablative acceleration scheme. High velocities of the macroparticles (foil fragments) produced and possibility of accelerating even rather heavy macroparticles are promising from the point of view of impact fusion studies, of the impact fast ignition, in particular.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Formation of a supersonic laser-driven plasma jet in a cylindrical channel

A simple method of supersonic plasma jet production where the jet is formed in a cylindrical channel guiding the plasma generated from a laser-irradiated thin foil target is proposed and examined. High-Mach number ({>=}10) plasma jets of parameters relevant to laboratory astrophysics applications using 120 J, 1.315 {mu}m, and 0.3 ns laser pulse for a thin CH foil irradiation are demonstrated. The method seems to be flexible in the production of jets of various compositions and hydrodynamic parameters and does not require high-energy lasers for the jet generation.

79 ASTRONOMY AND ASTROPHYSICS↗

Direct evidence of gas-induced laser beam smoothing in the interaction with thin foils

The process of laser beam homogenization in a gas medium placed in front of a thin metallic foil has been studied. Experiments were performed using the Prague Asterix Laser System iodine laser [Jungwirth et al., Phys. Plasmas 8, 2495 (2001)] working at 0.44 {mu}m wavelength and irradiance of about 10{sup 15} W/cm{sup 2}. Homogenization was detected both by directly analyzing the transmitted laser beam and by studying the shock breakout on the foil rear side. Results show that the gas ionization by the laser pulse induces a strong refraction and produces an effective smoothing of large-scale intensity nonuniformities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reversed scheme of thin foil acceleration

An alternative concept for accelerating thin foils to high velocity has been proposed and tested. The thin (10 {mu}m) Al foil has been accelerated by the ablative plasma generated by means of the third harmonic ({lambda}=0.438 {mu}m, {tau}=250 ps) of the iodine laser pulse of the energies of 75 and 190 J irradiating a massive Cu target. Two separation distances of the foil from the massive target of 100 and 500 {mu}m were used. It has been shown that this method of an indirect, two-step acceleration, named as the reversed acceleration scheme, can be more effective than the classic, direct-drive approach. The Al flyer foil has reached a velocity of {approx}1.3x10{sup 7} cm/s, i.e., significantly higher than that in the comparable ''classic'' ablative acceleration experiment.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Studies of supersonic, radiative plasma jet interaction with gases at the Prague Asterix Laser System facility

The interaction of laser driven jets with gas puffs at various pressures is investigated experimentally and is analyzed by means of numerical tools. In the experiment, a combination of two complementary diagnostics allowed to characterize the main structures in the interaction zone. By changing the gas composition and its density, the plasma cooling time can be controlled and one can pass from a quasiadiabatic outflow to a strongly radiation cooling jet. This tuning yields hydrodynamic structures very similar to those seen in astrophysical objects; the bow shock propagating through the gas, the shocked materials, the contact discontinuity, and the Mach disk. From a dimensional analysis, a scaling is made between both systems and shows the study relevance for the jet velocity, the Mach number, the jet-gas density ratio, and the dissipative processes. The use of a two-dimensional radiation hydrodynamic code, confirms the previous analysis and provides detailed structure of the interaction zone and energy repartition between jet and surrounding gases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The effect of high-Z dopant on laser-driven acceleration of a thin plastic target

Acceleration of a thin (10 or 20 {mu}m) plastic foil by 120 J, 0.438 {mu}m, 0.3 ns laser pulse of intensity up to 10{sup 15} W/cm{sup 2} has been investigated. It is shown that the introducing a high-Z dopant to the foil causes an increase in the ablating plasma density, velocity, and collimation which, in turn, results in a remarkably higher kinetic energy and energy fluence of the flyer foil.

36 MATERIALS SCIENCE↗