Engineering topics

Kruska, Karen

Publications and source records attributed to Kruska, Karen.

15 records

DOE OSTI2023

Behavior and properties of helium cavities in ductile-phase-toughened tungsten irradiated with He + ions at an elevated temperature

Ductile-phase toughened tungsten (DPT W) composites have demonstrated a great potential for plasma-facing components in fusion power systems. These materials can retain the outstanding thermomechanical properties of W while significantly enhancing the fracture toughness. The DPT W composite in this study consists of W particles (88 wt.%) embedded in a ductile NiFeW (12 wt.%) solution matrix. Irradiation of the composite was performed with 90 keV He + ions to 1.0 × 10 17 He + /cm 2 at 973 K. The He cavities formed in both W and NiFeW phases are examined using convergent-beam scanning transmission electron microscopy (CB-STEM) at an atomic-level resolution. Full-range depth profiles of the He cavity diameters and number densities are analyzed. The results show that the average cavity diameter in NiFeW is ~2.7 times that in W, while the number density is an order of magnitude lower. A quantitative analysis of the He density and pressure in the cavities is also achieved using STEM electron energy loss spectroscopy (STEM-EELS) mapping. The He atoms in the cavities in NiFeW are found to be under-pressurized, while those in similar-sized cavities in W are not detectable. Further, the He energy-loss shift exhibits a linear relationship with the He density in cavities in NiFeW, with the slope comparable to that for martensitic steel.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Effect of Applied Stress on the Selective Oxidation of Alloy 600 Exposed to PWR Primary Water and Rhines Pack Environments

A mechanistic understanding of corrosion and oxidation processes is crucial to ensure long-term resistance to stress corrosion cracking of Ni-base structural alloys in pressurized water reactor (PWR) primary and secondary systems. Aqueous corrosion of Ni-base alloys under PWR primary water conditions was previously compared to gaseous oxidation with comparable oxygen potentials. However, those studies considered only stress-free conditions, which removes a critical parameter for understanding stress corrosion behaviors. A significant knowledge gap exists for the role of applied stresses on selective internal oxidation in gaseous environments. A micro-4-point-bend jig was designed to facilitate stress in a Rhines Pack set-up. Selective oxidation at different stress and strain conditions was investigated in a series of Rhines Pack experiments for Alloy 600. Focused ion beam milling enabled the extraction of site-specific specimens containing selected high-energy grain boundaries from tensile and compressive stress regions. Analytical transmission electron microscopy was employed to analyze the microstructure and chemical composition of the resulting oxides. Protective surface oxide films and selective intergranular oxides were observed at different conditions. The implications of these fundamental differences are discussed relative to intergranular attack and stress corrosion cracking mechanisms in PWR primary water.

stress, 4-point-bend, selective oxidation, Alloy 6↗

DOE OSTI2022

Intergranular Oxidation of Unstressed Alloy 600 SA and Alloy 600TT in PWR Primary Water

Unstressed coupons of Alloy 600 SA (solution-annealed) and Alloy 600TT were exposed to simulated pressurized water reactor (PWR) primary water at 360oC. The depth of intergranular oxide penetration, as well as the microstructure and microchemistry associated with intergranular (IG) oxidation of selected samples, were characterized by SEM, serial FIB sectioning, TEM and APT. There is no clear trend to indicate that IG oxidation depths in unstressed coupons are different between Alloy 600 SA and TT. At the same time, all SA+TT materials examined evidenced significant interaction between oxidation and Cr-rich GB precipitates. In addition, the spatial extent of GB compositional changes ahead of the oxidation front (e.g. Cr depletion and Ni enrichment) appears different for Alloy 600 SA vs. SA+TT. In SA heats exposed for only 1000 h (42 days), the composition of some GBs changes over distances of 500–1000 nm. SA+TT materials appear not to develop such long-range GB compositional changes (10s nm alteration distances only).

Alloy 600, IGA, PWR, Oxidation, FIB, TEM, APT↗

DOE OSTI2022

Examination Of IASCC In 304 Stainless Steel Core Shroud From A Commercial Boiling Water Reactor (BWR)

The 304 stainless steel core shroud and the accompanying weld material from a commercial boiling-water reactor (BWR) experienced an estimated dose of ~3.5 dpa neutron irradiation leading to irradiation-assisted stress corrosion cracking (IASCC). The resulting IASCC crack tips are examined with high-resolution analysis techniques, including scanning electron microscopy (SEM), scanning transmission electron microscopy (STEM), and atom probe tomography (APT), with select examples of directly correlated STEM/APT observations. Analytical observations reveal the crack morphology, composition, microstructure, and any associated corrosion-induced or radiation-induced segregation in the local metal grain boundaries ahead of the propagating SCC cracks. The observed oxide composition and structure were in-line with expectations, consisting of a Cr-rich inner oxide and a Fe-rich outer oxide, with the leading crack tip oxide being Cr-rich. In addition, the leading grain boundary exhibited typical radiation-induced segregation signatures that were largely unperturbed by the accompanying corrosion. Finally, the quantitative capabilities and limitations of STEM and APT in the context of corrosion fronts and grain boundary chemistry from the directly correlated measurements are discussed.

Olszta, Matthew J.↗

DOE OSTI2022

Intergranular oxidation and oxygen transport in Ni-20Cr during exposure to model dry and wet oxidation environments

Selective oxidation is a critical component of the proposed internal oxidation mechanism of stress corrosion cracking (SCC) for Ni-based alloys in primary water reactor (PWR) operation. To isolate and study this process, the binary Ni-20Cr was exposed to pressurized water and a CO/CO2 gas mixture. In both environments, the oxygen potential was kept under the Ni/NiO line to stimulate penetrative intergranular attack. A combination of electron microscopy and atom probe tomography was used to study the nanometer-scale details of the passivation and penetrative intergranular oxidation processes at high-energy grain boundaries. Oxygen transport towards the terminating oxidation front is elucidated with dedicated usage of oxygen isotopic tracer exchange experiments to support classical theories of internal oxidation, revealing preferred oxygen transport paths were visualized with sub-nanometer resolution.

Weiser, Martin↗

DOE OSTI2022

Silver-Loaded Xerogel Nanostructures for Iodine Capture: A Comparison of Thiolated versus Unthiolated Sorbents

Here this paper describes the development and provides comparisons of thiolated (-SH) and unthiolated Ag-Al-Si-O xerogels for iodine gas capture. These xerogels were produced from alkoxides and then heat-treated at 350 °C to provide mechanical strength for subsequent processing steps. Then, a portion of the xerogels was thiolated using (3-mercaptopropyl)trimethoxysilane. Next, thiolated and unthiolated batches were ion-exchanged in AgNO 3 solutions where Ag + replaced Na + in the gel network on a near 1:1 molar basis. Subsamples of the Ag-exchanged xerogels were subjected to a reduction step in H 2 /Ar to convert Ag + to Ag 0 where the rest of the Ag-exchanged (Ag + ) were not reduced. X-ray diffraction, X-ray photoelectron spectroscopy, and transmission electron microscopy revealed nanoscale Ag 0 in the Ag + samples despite no active reduction where actively reduced samples had bimodal Ag 0 distribution of ~2-3 nm hexagonal and ~6-7 nm cubic crystallites. Synchrotron X-ray absorption spectroscopy was used to assess the oxidization states of Ag, S, and I within the different xerogel samples. The specific surface areas of the base xerogels decreased as subsequent treatments were performed on the as-made samples, albeit the decreases were smaller than aerogel equivalents of these samples from a previous study. All iodine-loaded Ag-based samples showed a mixture of β-AgI and γ-AgI. Comparisons of iodine-loading results with other Ag-based iodine sorbents show that the thiolated Ag 0 -xerogels in this work have one of the highest iodine-loading capacities (q e ) reported to date in saturated conditions with the thiolated Ag 0 -xerogel showing 522 mg iodine per g of the sorbent.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Formation and growth of cerium (III) oxalate nanocrystals by liquid-cell transmission electron microscopy

Using rare earth elements as analogs for actinide series elements enables studying the chemistry of these radioactive materials without the inherent risks. A fundamental understanding of the nucleation and growth of actinide oxalates is crucial for processing nuclear waste. Using in-situ liquid cell TEM (LC-TEM), we show particle attachment processes occurring during the nucleation and growth of cerium oxalate. The early stages of the observed non-classical growth mechanisms have important implications for particle evolution and predictions of final particle morphology. In this work, we observed particle formation via monomer-by-monomer addition or the particle aggregation pathway depending on the selected precursor concentration. At the highest precursor concentration at a high dose rate, we observed particle alignment in a branch structure is due to the interfacial instability. It was demonstrated that in-situ LC-TEM is an invaluable tool in studying the cerium oxalate formation and ultimately a path to understanding actinide chemistry.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Energy-Dispersive X-ray Spectroscopy and Atom-probe Tomography Data Quantifying Component-Ratios of Multicomponent Nano-Precipitates in Ion-Irradiated Ceria

Samples of ~1 µm films of CeO2 doped with 2 wt% Mo, 1.5 wt% Ru, 0.75 wt% Pd, 0.5 wt% Re and 0.25 wt% Rh grown with pulsed laser deposition were irradiated with I2+ ions (610°C and 730°C, 1016 and 5×1016 I2+/cm2). For selected samples post-irradiation heat treatment was conducted (900°C, 1100°C). The specimens were sectioned with focussed ion beam milling and characterized in a transmission electron microscope with energy dispesive x-ray spectroscopy, and with atom-probe tomography. Energy dispersive x-ray spectroscopy was used to obtain elemental maps showing the distribution of dopants in the specimen after exposure. Some of these maps are discussed in detail in our companion article “Formation of multicomponent alloy particles in doped ceria under I2+ ion irradiation and thermal annealing” in the Journal of Nuclear Materials [REF]. Advanced computational analysis could be used to more accurately quantify local compositions. Data is provided for additional regions of interest and one additional irradiation condition. The doped Ceria film that was heat treated at 1100 °C delaminated from the substrate in most places. Samples were extracted from the underside of a delaminated piece and analyzed with atom-probe tomography. The resulting data show Ceria and a Mo-rich particle and demonstrate that this approach is feasable in principle to study local compositions in a sample exposed to such extreme conditions.

multicomponent alloys, epsilon phase, EDS, atom pr↗

DOE OSTI2021