Engineering topics

Kuang, A. Q.

Publications and source records attributed to Kuang, A. Q..

8 records

DOE OSTI2023

Novel SOLPS-ITER simulations of X-point target and snowflake divertors

Abstract The design and understanding of alternative divertor configurations may be crucial for achieving acceptable steady-state heat and particle material loads for magnetic confinement fusion reactors. Multiple X-point alternative divertor geometries such as snowflakes and X-point targets have great potential in reducing power loads, but have not yet been simulated widely in codes with kinetic neutrals. This paper discusses recent changes made to the SOLPS-ITER code to allow for the simulation of X-point target and low-field side snowflake divertor geometries. Snowflake simulations using this method are presented, in addition to the first SOLPS-ITER simulation of the X-point target. Analysis of these results show reasonable consistency with the simple modelling and theoretical predictions, supporting the validity of the methodology implemented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Deep modeling of plasma and neutral fluctuations from gas puff turbulence imaging

The role of turbulence in setting boundary plasma conditions is presently a key uncertainty in projecting to fusion energy reactors. To robustly diagnose edge turbulence, we develop and demonstrate a technique to translate brightness measurements of HeI line radiation into local plasma fluctuations via a novel integrated deep learning framework that combines neutral transport physics and collisional radiative theory for the 3 3 D - 2 3 P transition in atomic helium with unbounded correlation constraints between the electron density and temperature. The tenets for experimental validity are reviewed, illustrating that this turbulence analysis for ionized gases is transferable to both magnetized and unmagnetized environments with arbitrary geometries. Based on fast camera data on the Alcator C-Mod tokamak, we present the first two-dimensional time-dependent experimental measurements of the turbulent electron density, electron temperature, and neutral density, revealing shadowing effects in a fusion plasma using a single spectral line.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Deep modelling of plasma and neutral fluctuations from gas puff turbulence imaging

The role of turbulence in setting boundary plasma conditions is presently a key uncertainty in projecting to fusion energy reactors. To robustly diagnose edge turbulence, we develop and demonstrate a technique to translate brightness measurements of HeI line radiation into local plasma fluctuations via a novel integrated deep learning framework that combines neutral transport physics and collisional radiative theory for the $3^3 D - 2^3 P$ transition in atomic helium. The tenets for experimental validity are reviewed, illustrating that this turbulence analysis for ionized gases is transferable to both magnetized and unmagnetized environments with arbitrary geometries. Based upon fast camera data on the Alcator C-Mod tokamak, we present the first 2-dimensional time-dependent experimental measurements of the turbulent electron density, electron temperature, and neutral density revealing shadowing effects in a fusion plasma using a single spectral line.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Dependence of the boundary heat flux width on core and edge profiles in Alcator C-Mod

This work presents new evidence that the heat flux width, λ q , in the Alcator C-Mod tokamak scales with the edge electron pressure, as observed in the ASDEX Upgrade (AUG) tokamak, but the scaling with volume-averaged pressure, $\bar{p}$, from the plasma stored energy, is a better predictor of λ q in Alcator C-Mod than the edge electron pressure. These previous studies, which find that λ q decreases with increasing plasma pressure, imply that a high performance core at high pressure will lead to challenging heat and particle exhaust due to very small λ q . This concern has led to our significant enlargement of the C-Mod database with the electron density, temperature, and pressure profile data from the Thomson scattering and electron cyclotron emission diagnostics. Using the C-Mod database augmented with new profile data, we find that λ q decreases with increasing edge electron pressure as ${\lambda }_{q}\propto {p}_{\mathrm{e},95}^{-0.26}$, similar to results from AUG, and showing the strength of cross-machine comparisons. We also find that ${\lambda }_{q}\propto {p}_{\mathrm{e},\mathrm{c}\mathrm{o}\mathrm{r}\mathrm{e}}^{-0.56}$, consistent with the original finding from C-Mod that the heat flux width scales as ${\bar{p}}^{-0.48}$. The scalings of λ q with separatrix pressure and gradient scale length are found to match the AUG results qualitatively. The C-Mod scalings with edge plasma quantities have more scatter than the $\bar{p}$ scaling, and, importantly, show different trends for H-modes relative to L- and I-mode. Furthermore, investigating the source of this discrepancy presents an opportunity for further study that may improve our ability to predict the heat flux width in different confinement scenarios in the pursuit of optimizing core-edge performance in future reactors.

Alcator C-Mod↗

DOE OSTI2021

The Digital Mirror Langmuir Probe: Field Programmable Gate Array Implementation of Real-Time Langmuir Probe Biasing

High bandwidth, high spatial resolution measurements of electron temperature, density and plasma potential are valuable for resolving turbulence in the boundary plasma of tokamaks. While conventional Langmuir probes can provide such measurements either their temporal or spatial resolution is limited: the former by the sweep rate necessary for obtaining I-V characteristics and the latter by the need to use multiple electrodes, as is the case in triple and double probe configurations. The Mirror Langmuir Probe (MLP) bias technique overcomes these limitations by rapidly switching the voltage on a single electrode cycling between three bias states, each dynamically optimised for the local plasma conditions. The MLP system on Alcator C-Mod used analog circuitry to perform this function, measuring Te, VF, and Isat at 1.1 MSPS. Recently, a new prototype digital MLP controller has been implemented on a Red Pitaya Field Programmable Gate Array (FPGA) board which reproduces the functionality of the original controller and performs all data acquisition. There is also the potential to provide the plasma parameters externally for use with feedback control systems. The use of FPGA technology means the system is readily customisable at a fraction of the development time and implementation cost. A second Red Pitaya was used to test the MLP by simulating the current response of a physical probe using C-Mod experimental measurements. This project is available as a git repository to facilitate extensibility (e.g. real-time control outputs, more voltage states) and scalability through collaboration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Study of passively stable, fully detached divertor plasma regimes attained in innovative long-legged divertor configurations

Numerical modeling of divertor configurations with radially or vertically extended, tightly baffled, outer divertor legs has demonstrated the existence of a passively-stable fully detached divertor regime. In the simulations, long-legged divertors provide up to an order-of- magnitude increase in peak power handling capability compared to conventional divertors. The key physics for attaining the passively stable, fully detached regime in these simulations involves the interplay of strong convective plasma transport to the divertor leg outer sidewall, confinement of neutral gas in the divertor volume, geometric effects including a secondary X-point, and atomic radiation. New analysis shows that in this regime the detachment front location is set by the balance between the power entering the divertor leg and the losses to the walls of the divertor channel. Correspondingly, the maximum power that can be accommodated by the divertor, while still staying detached, increases with the poloidal length of the leg. The detached regime access window in terms of input power, density and impurity seeding concentration varies quantitatively depending on divertor geometry and modeling assumptions most specifically, cross-field transport to the side walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Impurity screening behavior of the high-field side scrape-off layer in near-double-null configurations: prospect for mitigating plasma-material interactions on RF actuators and first-wall components

The impurity screening response of the high-field side (HFS) scrape-off layer (SOL) to localized nitrogen injection is investigated on Alcator C-Mod for magnetic equilibria spanning lower-single null, double-null and upper single null configurations under otherwise identical plasma conditions. L-mode, EDA H-mode and I-mode discharges are investigated. HFS impurity screening is found to depend on magnetic flux balance and the direction of B×?B relative to the most active divertor. Impurity ‘plume’ emission patterns indicate that both parallel and perpendicular (E×B) flows in the SOL contribute to the ‘flushing’ of impurities towards the active divertor, thereby affecting the overall impurity screening behavior. Despite the fact that the HFS scrape-off layer is extremely narrow in near-double-null configurations, this SOL is able to screen locally injected nitrogen at least as effectively as the low-field side (LFS) SOL – up to a factor of 10 more effective, depending on specific plasma conditions and whether the magnetic geometry produces parallel flows that work with or against E×B flows. For situations in which the E×B drift of the impurity ions opposes parallel flow toward the primary divertor, HFS impurity screening is found to be least effective. When E×B drifts assist parallel flow toward the primary divertor, HFS impurity screening is found to be very effective. These data support the idea of placing RF actuators and close-fitting wall components on the high-field side of the tokamak. With this configuration, near-double-null magnetic topologies may be used for active control of plasma parameters at the antenna/plasma interface for optimal RF coupling, mitigate the generation of local impurities from plasma-material interactions and, taking advantage of favorable plasma flows and good screening properties of the HFS SOL, further minimize the impact of wall-born impurity sources on the plasma core.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Projections of H-mode access and edge pedestal in the SPARC tokamak

In order to inform core performance projections and divertor design, the baseline SPARC tokamak plasma discharge is evaluated for its expected H-mode access, pedestal pressure and edge-localized mode (ELM) characteristics. A clear window for H-mode access is predicted for full field DT plasmas, with the available 25 MW of design auxiliary power. Additional alpha heating is likely needed for H-mode sustainment. Pressure pedestal predictions in the developed H-mode are surveyed using the EPED model. The projected SPARC pedestal would be limited dominantly by peeling modes and may achieve pressures in excess of 0.3 MPa at a density of approximately 3 × 10 20 m -3 . High pedestal pressure is partially enabled by strong equilibrium shaping, which has been increased as part of recent design iterations. Edge-localized modes (ELMs) with >1 MJ of energy are projected, and approaches for reducing the ELM size, and thus the peak energy fluence to divertor surfaces, are under consideration. The high pedestal predicted for SPARC provides ample margin to satisfy its high fusion gain (Q) mission, so that even if ELM mitigation techniques result in a 2x reduction of the pedestal pressure, Q > 2 is still predicted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗