Search NASA⌕ Search

Engineering topics

Kumar, A.

Publications and source records attributed to Kumar, A..

118 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Laminar and turbulent flows over a spherically blunted cone with massive surface blowing

Numerical solutions are presented for the flow over a spherically blunted cone with massive surface blowing. Time-dependent viscous shock layer equations are used to describe the flowfield. The boundary conditions on the body surface include a prescribed blowing rate distribution. The governing equations are solved by a time-asymptotic finite-difference method. Results presented here are only for a perfect gas-type flow at zero angle of attack. Both laminar and turbulent flow solutions are obtained. It is found that the surface blowing smooths out the effect of the curvature discontinuity at the sphere-cone juncture point on the laminar flowfield and results in a negative pressure gradient over the body. The shock slope increases on the downstream portion of the body as the surface blowing rate is increased. The turbulent flow with surface blowing is found to redevelop a boundary-layer-like region near the surface. The effects of this boundary-layer-like region on the flowfield and heating rates are discussed.

Kumar, A.↗
NASA NTRS1979

Nonequilibrium viscous flow over Jovian entry probes at high altitudes

The viscous chemical nonequilibrium flow around a Jovian entry body is investigated at high altitudes using two different methods. First method is only for the stagnation region and integrates the full Navier-Stokes equations from the body surface to the freestream. The second method uses viscous shock layer equations between the body surface and the shock. Due to low Reynolds numbers, both methods use surface slip boundary conditions and the second method also uses shock slip boundary conditions. The results of the two methods are compared at the stagnation point. It is found that the entire shock layer is under chemical nonequilibrium at higher altitudes and that the slip boundary conditions are important at these altitudes.

Kumar, A.↗
NASA NTRS1979

Laminar and turbulent flows over spherically blunted cone and hyperboloid with massive surface blowing

Numerical solutions are presented for the flow over a spherically blunted cone and hyperboloid with massive surface blowing. Time-dependent viscous shock-layer equations are used to describe the flow field. The boundary conditions on the body surface include a prescribed blowing-rate distribution. The governing equations are solved by a time-asymptotic finite-difference method. Results presented here are only for a perfect gas-type flow at zero angle of attack. Both laminar and turbulent flow solutions are obtained. It is found that the effect of the surface blowing on the laminar flow field is to smooth out the curvature discontinuity at the sphere-cone juncture point, which results in a positive pressure gradient over the body. The shock slope increases on the downstream portion of the body as the surface blowing rate is increased. The turbulent flow with surface blowing is found to redevelop a boundary-layer-like region near the surface. The effects of this boundary-layer region on the flow field and heating rates are discussed.

Kumar, A.↗
NASA NTRS1978

Comparative study of the convergence rates of two numerical techniques

The paper examines the applicability of the three-step Stetter (1968) method to the problem of hypersonic viscous flow over a blunt axisymmetric body used for planetary entry probes at zero angle of attack. The flow-field results using the two-step finite-difference MacCormack (1969) method are reported by Kumar and Graves (1977). Only the computational efficiency of Stetter's method is compared with that of MacCormack's in terms of the iterative time steps and computing time required for the steady-state solution. Advantages of Stetter's method over MacCormack's are established.

Kumar, A.↗
NASA NTRS1978

Effects of small angle of attack on the radiating viscous shock layer solutions for Jovian entry

Results are presented for the laminar and turbulent flows of a reacting mixture of hydrogen-helium in chemical equilibrium over blunted cones of large half angles at small angles of attack. The freestream conditions correspond to a typical Jovian entry trajectory point. Radiative heat flux is calculated by using a realistic step-function model for the absorption coefficient. An investigation is also made to determine whether a blunted cone at small angles of attack can be replaced by equivalent bodies at zero angle of attack for the purpose of calculating the shock shapes, surface pressure, skin friction and heating rates.

Kumar, A.↗
NASA NTRS1977

Low Reynolds number flow past a blunt axisymmetric body at angle of attack

Low Reynolds number flow of an ideal gas over a blunt axisymmetric body of large half-angle at small angles of attack is investigated, for the case of laminar hypersonic flow. Time-varying viscous shock layer equations describing the flowfield are obtained from the full Navier-Stokes system by keeping terms to second order in the inverse square root of Re in both viscous and inviscid regions; the equations are valid for moderate to high Re. Drag, skin friction, and heating rates were obtained at small (or zero) angles of attack. Conditions experienced by planetary entry probes during the high-altitude (early) legs of an atmospheric entry trajectory are pertinent to the problem.

Kumar, A.↗
NASA NTRS1977

Numerical solution of the viscous hypersonic flow past blunted cones at angle of attack

Hypersonic viscous flow over spherically blunted cones of large half angle is computed at small angles of attack in the plane of symmetry of the flow field. Time-dependent viscous shock-layer equations in body-oriented coordinates are used to describe the flow field. The shock wave is treated as a discontinuity, across which the Rankine-Hugoniot relations are used to compute the flow conditions behind the shock. A time-marching second-order finite-difference method is used to solve the equations for a perfect gas. The local CFL (Courant-Friedrich-Lewy) time increment is used to advance the solution in time at each grid point. A fourth-order damping is used to damp the oscillations in the flow quantities. The numerical results of the present analysis for quantities such as shock standoff distance, surface-pressure distribution, and heating rates compare well with the existing theoretical and experimental results.

Kumar, A.↗
NASA NTRS1974

The effect of yttrium and thorium on the oxidation behavior of Ni-Cr-Al alloys

The investigation reported included a determination of the optimum composition of a Ni-Cr-Al ternary alloy with respect to oxidation resistance and minimum film-spalling tendencies. Yttrium and thorium in small amounts were added to the ternary alloy and an investigation of the oxidation mechanism and the oxide scale adherence was conducted. It was found that the oxidation mechanism of Ni-Cr-Al ternary alloys depends upon the composition of the alloy as well as the time, oxygen pressure, and temperature of oxidation.

Kumar, A.↗
NASA NTRS1974

The effect of yttrium and thorium on the oxidation behavior of Ni-Cr-Al alloys

The effect of quaternary additions of 0.5% Y, 0.5 and 1.0% Th to a base alloy of Ni-10CR-5Al on the oxidation behavior and mechanism was studied during oxidation in air over the range of 1000 to 1200 C. The presence of yttrium decreased the oxidation kinetics slightly, whereas, the addition of thorium caused a slight increase. Oxide scale adherence was markedly improved by the addition of the quaternary elements. Although a number of oxides formed on yttrium containing alloys, quantitative X-ray diffraction clearly showed that the rate-controlling step was the diffusion of aluminum through short circuit paths in a thin layer of alumina that formed parabolically with time. Although the scale adherence of the yttrium containing alloy was considerably better than the base alloys, spalling did occur that was attributed to the formation of the voluminous YAG particles which grew in a mushroom-like manner, lifting the protective scale off the subrate locally. The YAG particles formed primarily at grain boundaries in the substrate in which the yttrium originally existed as YNi9.

Kumar, A.↗