Search NASA⌕ Search

Engineering topics

Kumar, K.

Publications and source records attributed to Kumar, K..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

MOLLER Spectrometer Magnet Design With Measured Mechanical Properties of Irradiated S2-Glass Reinforced Cyanate Ester Resin at Elevated Temperature

Here, the aim of this study was to retire the risk of maintaining the integrity of S2-glass reinforced CTD-403 (a cyanate ester resin) that is exposed to radiation and elevated temperature over the life of the measurement of a lepton–lepton electroweak reaction (MOLLER) experiment in experimental Hall A at Jefferson Lab, Newport News, VA. In this article, the shear strength and flexural modulus of irradiated S2-glass reinforced CTD-403 specimens were measured at 65 °C (the magnets are to operate at less than 65 °C) under two scenarios: vacuum and gaseous nitrogen. The testing method is the short-beam shear (SBS) test according to ASTM D2344. The specimens were exposed to neutrons and gamma rays up to 124 MGy. The results show that specimens have excellent resistance against radiation, only 23% degradation of apparent shear strength with 124 MGy at 65 °C under vacuum. At the highest dose areas of the coils, tungsten plates are used to reduce the radiation dose to the resin system. The conclusion is that S2-glass reinforced CTD-403 is well-suited for electrical insulation of MOLLER magnets.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Design and Prototyping of a Novel Toroidal Magnet System for MOLLER Experiment at Jefferson Lab

The Thomas Jefferson National Accelerator Facility (JLab) has designed a unique spectrometer system to measure the weak interaction between electrons. The experiment— Measurement of Lepton-Lepton Electroweak Reaction (MOLLER)—requires leveraging the recent 12 GeV electron beam upgrade and will run in JLab for three years. Focusing the signal for the MOLLER experiment requires five water-cooled toroidal magnets, each with unique geometry and with 7-fold symmetry. The five magnets operate in a vacuum and provide the magnetic field required to separate the incident beam electrons scattered from the target electrons (Møller scattering) and protons (elastic e-p scattering) in a liquid hydrogen target. The conceptual design was developed by the MOLLER Collaboration and was given to JLab in the form of amp turns and physical location, with additional physics requirements. This article presents prototyping of the coils and magnet support system and discusses the lessons learned during the process along with the plans for full magnet testing and installation. The JLab Magnet Group along with the MOLLER Collaboration developed the specification document that includes keep out zones to design the set of magnets. JLab contracted the design of the first toroid magnet (TM0) of the magnet system to Massachusetts Institute of Technology. The other four toroid magnets (TM1 through TM4) have been designed by JLab and are in the process of fabrication and assembly. Prototype coils of TM1-TM4 were fabricated by Everson-Tesla Incorporated, PA (USA). Finally, this article presents the unique challenges of the design, alignment, high current density, operating range, high radiation dose, and vacuum environment.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS2010

Identification of a New Spinel-Rich Lunar Rock Type by the Moon Mineralogy Mapper (M (sup 3))

The canonical characterization of the lunar crust is based principally on available Apollo, Luna, and meteorite samples. The crust is described as an anorthosite-rich cumulate produced by the lunar magma ocean that has been infused with a mix of Mgsuite components. These have been mixed and redistributed during the late heavy bombardment and basin forming events. We report a new rock-type detected on the farside of the Moon by the Moon Mineralogy Mapper (M3) on Chandrayaan-1 that does not easily fit with current crustal evolution models. The rock-type is dominated by Mg-spinel with no detectible pyroxene or olivine present (<5%). It occurs along the western inner ring of Moscoviense Basin as one of several discrete areas that exhibit unusual compositions relative to their surroundings but without morphological evidence for separate processes leading to exposure.

Pieters, C. M.↗
NASA NTRS1990

Analytical estimation for static deformation of wire ropes with fibrous core

This paper develops closed-form solutions for the extension of twisted wire ropes with fibrous cores which are subjected to axial forces as well as axial moments. The analytical results are compared with the corresponding numerical results obtained by Costello and Phillips. A close agreement between the two establishes validity of the analytical solutions. Finally, an expression for the effective rigidity modulus of wire ropes with fibrous core is obtained in terms of the helix angle and the number of helical wires in the rope for each of the two end conditions.

Kumar, K.↗
NASA NTRS1988

Analysis of coils of wire rope arranged for passive damping

Vibration dampers constructed with multiple loops of wire rope are studied. The literature on such devices is reviewed briefly, and dynamic and static models of them are examined. Fundamental and advanced NASTRAN models for wire rope damping are considered.

Cutchins, M. A.↗
NASA NTRS1987

Closed-form analysis for elastic deformations of multilayered strands

Closed-form solutions are developed for elastic deformation characteristics of multilayered strands under tensile and torsional loads. These analytical results are successfully applied to obtain expressions for the effective extensional and torsional moduli of rigidity for the strands. Finally, a simple design criterion is established for 'nonrotating' cables.

Kumar, K.↗
NASA NTRS1987

Initial investigations into the damping characteristics of wire rope vibration isolators

Passive dampers composed of coils of multi-strand wire rope are investigated. Analytical results range from those produced by complex NASTRAN models to those of a Coulomb damping model with variable friction force. The latter agrees well with experiment. The Coulomb model is also utilized to generate hysteresis loops. Various other models related to early experimental investigations are described. Significant closed-form static solutions for physical properties of single-and multi-strand wire ropes are developed for certain specific geometries and loading conditions. NASTRAN models concentrate on model generation and mode shapes of 2-strand and 7-strand straight wire ropes with interfacial forces.

Cutchins, M. A.↗
NASA NTRS1987

A new approach for vibration control in large space structures

An approach for augmenting vibration damping characteristics in space structures with large panels is presented. It is based on generation of bending moments rather than forces. The moments are generated using bimetallic strips, suitably mounted at selected stations on both sides of the large panels, under the influence of differential solar heating, giving rise to thermal gradients and stresses. The collocated angular velocity sensors are utilized in conjunction with mini-servos to regulate the control moments by flipping the bimetallic strips. A simple computation of the rate of dissipation of vibrational energy is undertaken to assess the effectiveness of the proposed approach.

Kumar, K.↗
NASA NTRS1987

New Polymeric Precursors of Silicon Carbide

Silicon carbide made by pyrolizing polymers. Method conceived for preparation of poly(decamethylcyclohexasilanes) as precursors for preparation of silicon carbide at high yield. Technical potential of polysilanes as precursors of SiC ceramics being explored. Potential limited by intractability of some polysilanes; formation of small, cyclic polycarbosilane fragments during pyrolysis; and overall low char yield and large shrinkage in conversion to ceramics.

Litt, M.↗
NASA NTRS1987

Analytical solutions for static elastic deformations of wire ropes

This paper develops closed-form solutions for extension of twisted wire ropes subjected to axial forces for two different end conditions. The analytical results are compared with the corresponding numerical results obtained by Costello and Phillips. A close agreement between the two establishes validity of the analytical solutions. Finally, an expression for the effective rigidity modulus of the wire ropes is obtained in terms of the helix angle and the number of helical wires in the rope for each of the two end conditions.

Kumar, K.↗
NASA NTRS1986

Polymer precursors for ceramic matrix composites

The synthesis and characterization of a polycyclohexasilane is reported. Because of its cyclic structure, it is anticipated that this polymer might serve as a precursor to SIC having a high char yield with little rearrangement to form small, volatile cyclic silanes, and, as such, would be of interest as a precursor to SiC composite matrices and fibers, or as a binder in ceramic processing. Several approaches to the synthesis of a bifunctional cyclic monomer were attempted; the most successful of these was metal coupling of PhMeSiCl2 and Me2SiCl2. The procedure gives six-membered ring compounds with all degrees of phenyl substitution, from none to hexaphenyl. The compounds with from 0-2 groups were isolated and characterized. The fraction with degree of phenyl substitution equal to 2, a mixture of cis and trans 1,2-; 1,3-; and 1,4 isomers, was isolated in 32 percent yield. Pure 1,4 diphenyldecamethylcyclohexasilane was isolated from the mixed diphenyl compounds and characterized. Diphenyldecamethylcyclohexasilanes were dephenylated to dichlorodecamethylcyclohexasilanes by treating with H2SO4.NH4Cl in benzene. The latter were purified and polymerized by reacting with sodium in toluene. The polymers were characterized by HPGPC, elemental analysis, proton NMR, and IR. Thermogravimetric analyses were carried out on the polymers. As the yield of residual SiC was low, polymers were heat treated to increase the residual char yield. As high as 51.52 percent residual char yield was obtained in one case.

Litt, M. H.↗
NASA NTRS1986

Semi-analytical theory for long-term rotational motion of uncontrolled satellites

Analytical solutions/integrals of the free rotational motion of uncontrolled satellites which contain spinning rotors are employed in conjunction with a suitable analytical/numerical averaging approach to predict long-term attitude motion. This semi-analytical method of averaging is basically similar to the one used in purely analytical 'general perturbation' theories. However, in view of the complexities involved in analytical treatment of the problem, its application is primarily numerical in character. An example is presented illustrating the use of the theory to predict the attitude motion of an axisymmetric satellite containing symmetrical constant-speed rotors under gravity-gradient torque. The use of the theory is considerably more efficient than straightforward numerical integration of the complete set of equations of motion.

Lahr, B. S.↗
NASA NTRS1985

Samarium/Cobalt Magnets

Intrinsic magnetic coercivities of samarium cobalt magnets made to approach theoretical limit of 350 kA/m by carefully eliminating oxygen from finished magnet by hot isostatic pressing (HIP). HIP process viable alternative to currently used sintering process.

Das, D.↗
NASA NTRS1982

Electromagnetic containerless reaction of samarium with cobalt for the formation of samarium-cobalt alloys

The electromagnetic levitation technique has been used to obtain nearly stoichiometric SmCo5, with the reaction temperature controlled by a gas jet. The results of several experiments carried out at a 450 kHz, 25 kw RF power levitation facility using different reaction times and cooling rates are presented. It is shown that reaction rates achieved with the levitation technique are larger than the expected diffusion rate in the system liquid samarium-solid cobalt. It is also shown that substantial mixing occurs in the RF-levitated melt.

Chang, C. W.↗
NASA NTRS1982

Ultimate intrinsic coercivity samarian-cobalt magnet. An Earth based feasibility study for Space Shuttle missions

Techniques for the electromagnetic containerless reaction of samarium with cobalt for the formation of samarium-cobalt alloys are summarized. The effort expended to reduce and instrument the oxygen partial pressure in the reaction chamber and coolant gas system are described as well as the experiments in which these improvements were shown to be partially effective. A stainless steel glove box capable of being evacuated to low 10 to the -6th torr pressure and refilled with ultra-pure argon was built and installed. Necessary accessories to perform SmCo5 powder preparation, compaction and subsequent encapsulation of the powder inside a hot isostatic pressing cannister were designed, built, and incorporated into the chamber. All accessories were tested for proper functioning inside the chamber. Using the facility, the first batch of densified SmCo5 powder was fabricated to near total density. Analysis of the densified compacts shows that oxygen contamination during fabrication was near zero.

Das, D.↗
NASA NTRS1982

An NNSS satellite timing receiver

The U.S. Navy Navigation Satellite System, NNSS, offers a unique worldwide facility for precise time synchronization. Space Applications Centre (SAC) developed a simple timing receiver. Using this timing receiver first the internal time consistency of NNSS was studied and then its performance to synchronize time was compared with that of National Time Standard. The methodology of data analysis, results, and various sources of error which affect the time transfer accuracy were studied and described. The main source of error was found to be the receiver delay which varies with signal strength. It is possible to apply that this delay correction empirically provided signal strength is recorded.

Jain, C. L.↗