Search NASA⌕ Search

Engineering topics

Kunc, Vlastimil

Publications and source records attributed to Kunc, Vlastimil.

At least 19 records

Vertical z-axis discontinuous carbon fibers for improved lightning strike performance of continuous fiber-reinforced polymer composites

Effective lightning strike protection for critical aerospace and wind applications requires high electrical conductivity to dissipate current efficiently. However, polymer matrix composites face a challenge due to their inherently insulating nature. While conventional carbon fiber-reinforced composites (CFRP) exhibit electrical conductivity in the planar direction, achieving through-thickness conductivity remains an ongoing challenge. In this work, we have undertaken the fabrication of CFRP interleaved with vertically oriented carbon fibers (Z-fiber) to impart higher electrical conductivity along the thickness direction. Two Z-fiber composite variations are prepared: Z-1 with a single layer of Z-fiber and Z-5 with five interleaved layers and compared with no Z-fiber layer (Z-0) composite. The composite panels were subjected to lab-scale lightning strike tests with a current magnitude of 100 kA. To emulate real-world service conditions, an aerospace-grade paint coating was applied to the composite laminates. Comparative analysis shows Z-1 reduces damage diameter to ∼22 mm compared to Z-0 (∼26 mm), while Z-5 exhibits the least damage (∼16.7 mm), confirmed by optical microscopy. Z-5 demonstrates nine times higher through-thickness electrical conductivity than Z-0, reducing electrical anisotropy substantially. Thermal-electric finite element damage modeling predicts surface damage within 6% of experimental values for both Z-0 and Z-5 composites. Flexural tests post-lightning reveal Z-5 retains 66% flexural strength and 86% modulus, significantly better than Z-0, which retains less than 40% for both properties. This study highlights the efficacy of Z-fiber composites in lightning strike protection, offering improved through-thickness conductivity and mechanical property retention.

36 MATERIALS SCIENCE↗

Innovative Joining Method for Hybrid Composites with Tailored Performance

In various industries, such as renewables and aerospace, the demand for carbon fiber is rapidly growing to meet the requirements of high-performance applications with optimized designs. Traditionally, these optimized designs have been limited to single-material composites due to process constraints. However, this study aims to explore the feasibility of transitioning between two different fiber types for pultrusion and filament winding processes, thereby enhancing design flexibility, and optimizing performance. This research introduces a novel method of hybrid reinforcement through splicing techniques. By employing a splicing method, fibers are merged prior to infusion, resulting in a transition of higher strength compared to traditional joints. Moreover, this technique enables the creation of composites with variable compositions, allowing for the selective placement of properties in a process previously characterized by static properties. The objective of this paper is to evaluate the mechanical properties of dry fiber splicing and its impact on the resulting composite material. Through comprehensive analysis, we aim to provide insights into the feasibility and advantages of employing this innovative splicing technique in composite manufacturing processes.

Guzorek, Steven↗

Design optimization of lightweight automotive seatback through additive manufacturing compression overmolding of metal polymer composites

With the growing demand for enhanced automotive fuel efficiency and environmental sustainability, there is a need for lightweighting automotive components through innovative design and manufacturing processes. Here, this study leverages a combination of numerical iterative design optimization and hybrid additive manufacturing–compression molding (AM-CM) technique for metal polymer composites to lightweight an automotive seatback. The AM-CM process enables robust mechanical interlocking between metals and composites, boasting high stiffness and strength with low overall density. Replacing metallic components with such metal polymer composites allows for comparable mechanical performance while significantly reducing the overall weight. First, the automotive seatback design space is reduced to critical load carrying regions using topology optimization and high stress concentration areas are identified using finite element analysis. Next, a lightweight metal polymer subcomponent is designed for a high stress concentration region. The full seatback frame with spatially heterogeneous material-specific design is then iteratively optimized to enable enhanced stiffness with minimal weight. Overall, the automotive seatback frame designed with location-specific metal, polymer, and metal polymer composite materials weighs 20% less than the metal-only design while exhibiting similar stiffness.

36 MATERIALS SCIENCE↗

Recent and future developments in pultrusion technology with consideration for curved geometries: A review

Herein this paper examined the current state and future developments in pultrusion with particular emphasis on its application in curved part manufacturing. The relationship between factors such as resin chemistry, fiber characteristics, and die geometry that influences the properties of pultruded product were highlighted. Moreover, the specific challenges associated with pultruding curved parts such as the complexities in achieving uniformity and structural integrity in such geometries were discussed. The review emphasized mold design, process improvement, adaptive control systems for precise resin impregnation and material selection to address these challenges. Additionally, the paper suggests the integration of real-time monitoring and data analytics as ways to enhance quality control during curved parts pultrusion. These advancements will help to overcome challenges specific to curved pultrusion and make the process more efficient. Other manufacturing techniques such as filament winding, thermoforming, pulforming were mentioned as alternatives to curved parts pultrusion. The review also explores pultruded variable curvature processes, highlighting some notable patents and article related to this subject matter. Production of pultruded variable curvature parts was seen as a key driver that can shape the future of pultrusion. Finally, the paper anticipates future trends, with sustainability, customization, integration of advanced materials, and development of techniques for pultrusion of composites parts.

42 ENGINEERING↗

In-Process Monitoring and Structural Health Monitoring of Large-Scale Additive Manufacturing Using Acoustic Emission Technique

ORNL collaborated with MISTRAS Group, Inc. to investigate acoustic emission (AE) as a structural health monitoring (SHM) method for large-scale additive manufacturing (AM). Large-scale AM is being adapted as method of producing large structures in a short lead time and cost-effective way. With the growing advancement in AM techniques and application, machine monitoring and part qualification is highly needed. There has been leading research focused on the manufacturing, feedstock material but minimum research on the SHM, defect detection, and nondestructive evaluation (NDE) for AM. Scanning large structure using conventional nondestructive testing (NDT) techniques, such as ultrasound or X-ray, and searching for potential defects can be very time consuming, challenging and cost prohibitive. AE is a passive technique that can be used to monitor and locate defect progression in large structure by distributing group of sensors around the part. This project utilized AE technique and system manufactured/designed by MISTRAS Group to monitor large-scale AM equipment (i.e. Big Area Additive Manufacturing (BAAM) system located at the Oak Ridge National Laboratory – Manufacturing Demonstration Facility (ORNL-MDF) and the printed parts it produces. The AE system provided valuable insight on defect development/progression during and post-printing process.

36 MATERIALS SCIENCE↗

Additive Manufacturing of Dissolvable Mandrels

ORNL collaborated with Mitsubishi Chemical America to investigate different grades of vinyl alcohol co-polymers as a potential feedstock material for large-scale material extrusion additive manufacturing (AM). Dissolvable polymers and can find potential applications in AM tooling for complex, hollow, and trapped composite structures without the need for specialized molds and tools. This CRADA Phase I work involved analysis of three different developmental grades of vinyl alcohol co-polymers for thermal and rheological properties, followed by print trials on the Big Area Additive Manufacturing (BAAM) system using these materials. Finally, printed part properties, including mechanical and thermal performance, as well as dissolvability were evaluated. The properties and performance evaluated in this phase of the project have provided guidelines to further develop these vinyl alcohol co-polymers to enable large-scale printing at high deposition rates and obtain parts that satisfy high temperature molds and dies requirements.

36 MATERIALS SCIENCE↗

Effect of Internal Structure on Warpage in a Large-Scale Additive Manufacturing Process With Bio-Derived Composites

Extrusion-based large-format additive manufacturing (LFAM) often results in unintended deformation and failures due to thermal residual stress between layers. This LFAM involves a hot molten polymer deposited on a previously deposited and cooled layer, generating a temperature mismatch between the layers. The temperature discrepancy causes a thermal contraction mismatch, generating thermal residual stress. Due to the residual stress, printed structures experience warpage and delamination Therefore, understanding the heat distribution behavior is essential to preventing undesired deformation and failures. The goal of this study is to investigate the effect of infill patterns on heat distribution and deformation in an LFAM system. Wood fiber-reinforced polylactic acid was used as a sustainable and low-cost reinforcement material. A numerical model was developed to predict the temperature and deformation field with thermo-mechanical properties, which were measured by a dynamic mechanical analysis and a thermal expansion test. Simulations were performed on a box geometry with three different infill patterns. The simulation model was verified with temperature data gathered from an infrared camera. The results show good agreement between predicted and measured temperature profiles. The developed simulation model was applied to a roof tray with different infill patterns for a case study. We found that the different thermal mass distributions resulting from the various infill patterns affected the heat distribution and deformation. These findings contribute to a better understanding of the thermal and mechanical behavior of LFAM.

Jo, Eonyeon↗

Evaluation of Dissolvable Additively Manufactured Molds and Supports for Electroimpacts Innovative Additive Manufacturing Process

Electroimpact inc. has developed a new additive manufacturing process involving continuous fiber reinforcement along with high-strength thermoplastics. A unique part of this process includes using additive manufacturing to print a base geometry that is then used as a tool for continuous fiber placement. Ideally the tool should be disposable and cost effective. After printing the base tool, continuous fiber is printed on top of the tool using a secondary additive head on the same system to create the final printed part. After continuous fiber printing is completed, the tool is removed and disposed of to leave only the final desired structure. Materials used for the base tool have several requirements that must be met in order to complete this process. First, the material must be rigid and strong enough to support the loads from the secondary printing operation (continuous fiber printing). In addition, the material must be able to adhere to the secondary process material as well be capable of being removed such that the only remaining structure is continuous fiber composite. Using innovative soluble materials allows for parts to be produced through additive with molds that are produced as non-reusable one-off shapes and sizes.

36 MATERIALS SCIENCE↗

3D printable polymeric lightning strike protection system for fiber reinforced composites

The current embodiments include all-polymeric protective material for mitigating lightning strike damage. The protective material includes a hybrid matrix comprising PANI and MXene dispersed within a thermosetting epoxy resin. This hybrid matrix can be painted, printed, or applied as a conductive polymeric layer to a FRCP structure, for example an aircraft fuselage, wing, empennage, control surface (aileron, flap, slats, rudder, elevator) or a wind turbine blade. The protective material not only withstands lightning strikes, but also functions as shielding against electromagnetic interference and is corrosion-resistant and lightweight.

Kumar, Vipin↗

Development of multifunctional nylon 6,6-based nanocomposites with high electrical and thermal conductivities by scalable melt and dry blending methods for automotive applications

With the advent of intelligent automobile technology, the demand for multifunctional composites with higher electrical and thermal conductivities is increasing. We have herein reported for the first time the effect of polyolester on the dispersion of carbon nanotube (CNT) in the short-carbon fiber (CF)/nylon 6,6 (PA66) composite using a scalable melt-mixing and dry-blending method and its subsequent improvement in electrical and thermal conductivities. Masterbatches were prepared with a higher concentration of CNT (both untreated and polyolester-treated) followed by dry blended with reference composite (30 wt% CF and 10 wt% mineral fiber filled PA66) before making coupons via injection molding. A 500% and 63% improvements in electrical (3.14 S cm -1 ) and thermal conductivities (in-plane) (1.99 W m -1 K -1 ) conductivities were observed by adding 1.5 wt% treated CNT compared to the reference composite. The improvements were even higher than that of untreated CNT due to better dispersion. Furthermore, the electromagnetic shielding effectiveness reached 61 dB for 1.5 wt% treated CNT-filled composite (39% enhancement). In conclusion, these results are significant in imparting multiple functionalities to the automotive composite parts.

36 MATERIALS SCIENCE↗

System and method for simulation-assisted additive manufacturing involving estimating anisotropic deformation

A simulation-assisted additive manufacturing system and method for generating an anisotropic compensation to account for non-uniform deformation due to additive manufacturing and service loading. The predicted deformation may not be fully defined. The present disclosure provides a system and method for estimating the missing deformation data through regression analysis. The present disclosure also provides an integrated framework where the various simulated-assisted design modules are configured for two-way communication and sharing access to changes to the model.

Kim, Seokpum↗

Additive Manufacturing of Self‐Sensing Carbon Fiber Composites

Carbon fiber-reinforced polymer (CFRP) composites have gained substantial attention across various industries owing to their exceptional mechanical properties and lightweight nature. The emergence of additive manufacturing technologies brings new opportunities to the industry, offering advantages such as design freedom, rapid prototyping, and customization. However, the fabrication of CFRP composites through 3D printing techniques poses challenges pertaining to low resolution and limitations in complex geometry realization. This work introduces digital light processing printing as a versatile, high-resolution method ideal for CFRP composite fabrication. Furthermore, the development and characterization of CFRP are focused on and the manipulation of mechanical properties through variations in matrix resins and fiber loadings is investigated, showcasing the versatility of CFRP composites for tailored applications. Additionally, the integration of self-sensing capabilities in CFRP structures is explored, which opens up opportunities for applications in smart components for automotive and structural health monitoring.

carbon fiber composites↗

Enhanced lightning strike protection using vertically oriented carbon fiber melded with conventional carbon fiber-reinforced composite and its validation through damage analysis

Lightning strike protection (LSP) is one of the prime factors in aerospace and wind industries concerning safety, enhanced service life, and reduced downtime. To ensure better LSP, high electrical conductivity is required to dissipate the current, which is always a challenge for polymer composites due to the inherent insulating nature of the polymer matrix. Conventional carbon fiber-reinforced composites (CFRP) offer electrical conductivity in the planar direction while the vertical i.e. through-thickness conductivity still remains a challenge. Having been motivated by this fact, we have fabricated CFRP interleaved with vertically oriented CF (Z-fiber) for the lightning strike test (100 kA). A paint was applied to mimic the actual service condition of the composite laminates. We have prepared two Z-fiber composites: (a) Z-1 containing one Z-fiber layer on the top along with conventional CF layers and (b) Z-5 containing five interleaved Z-fiber layers and compared the properties with conventional CFRP (Z-0). Interestingly, even a single Z-fiber layer (Z-1) showed lower damage (visual damage diameter 22 mm) than Z-0 (visual damage diameter 26 mm). Z-5 displayed the lowest damage (visual damage diameter 16.7 mm), which was further confirmed by cross-sectional optical microscopy. Improved LSP was attributed to the higher through-thickness electrical conductivity in the case of Z-5 (9 times with respect to Z-0) reflecting a lower electrical anisotropy for Z-fiber composites. The residual mechanical property after the lightning test was analyzed through the flexural test, and the retention of flexural strength and modulus was 66% and 86%, respectively for Z-5 showing a significant improvement in comparison to Z-0 (>40% for both).

Saha, Subhabrata↗

Systems and methods for generating a molecular dynamic graded lattice structure and their application to additive manufacturing

Systems and methods for generating molecular dynamic graded lattice structures that can be used as infill for additively manufactured articles. Molecular dynamically generated lattice infill is based on force balancing a node distribution instead of a circle packing. Field data can be utilized to adjust the spacing of the node distribution according to a force balance equilibrium model that accounts for the field expected to be experienced by the article being additively manufactured. The resultant non-uniform honeycomb structures from force-balancing robustly and efficiently address the connection issues with traditional non-uniform lattice structures.

Kim, Seokpum↗