Kuo, S. | Search NASA

NASA NTRS1993

(abstract) Hermes Global Orbiter: Mission to Mercury

The Hermes Global Orbiter is a proposed Discovery-class mission. Hermes will be launched aboard a Delta II rocket in 1999 and will be placed in an elliptical polar orbit about Mercury. Remote sensing measurements of the planet's surface, atmosphere, and magnetosphere will be performed. Key mission goals include mapping the entire surface at 1 km resolution, characterizing the surface composition, texture and topography, searching for water ice at the poles, characterizing the atmosphere, and constraining the interior structure.

Mercury Hermes orbiter remote sensing surface atmo↗

NASA NTRS1992

TIMS performance evaluation summary

The purpose of this effort was to investigate the Thermal Infrared Multispectral Scanner (TIMS) operation under various conditions to determine what effect, if any, there is on the TIMS performance. This effort was undertaken because of reports from investigators that the TIMS is not performing as expected when flown on the ARC C-130. This effort was initiated with a meeting at Stennis Space Center (SSC) with representatives from SSC, Jet Propulsion Laboratory (JPL), and ARC.

Spiering, Bruce↗

NASA NTRS1992

Analysis of TIMS performance subjected to simulated wind blast

The results of the performance of the Thermal Infrared Multispectral Scanner (TIMS) when it is subjected to various wind conditions in the laboratory are described. Various wind conditions were simulated using a 24 inch fan or combinations of air jet streams blowing toward either or both of the blackbody surfaces. The fan was used to simulate a large volume of air flow at moderate speeds (up to 30 mph). The small diameter air jets were used to probe TIMS system response in reaction to localized wind perturbations. The maximum nozzle speed of the air jet was 60 mph. A range of wind directions and speeds were set up in the laboratory during the test. The majority of the wind tests were conducted under ambient conditions with the room temperature fluctuating no more than 2 C. The temperature of the high speed air jet was determined to be within 1 C of the room temperature. TIMS response was recorded on analog tape. Additional thermistor readouts of the blackbody temperatures and thermocouple readout of the ambient temperature were recorded manually to be compared with the housekeeping data recorded on the tape. Additional tests were conducted under conditions of elevated and cooled room temperatures. The room temperature was varied between 19.5 to 25.5 C in these tests. The calibration parameters needed for quantitative analysis of TIMS data were first plotted on a scanline-by-scanline basis. These parameters are the low and high blackbody temperature readings as recorded by the TIMS and their corresponding digitized count values. Using these values, the system transfer equations were calculated. This equation allows us to compute the flux for any video count by computing the slope and intercept of the straight line that relates the flux to the digital count. The actual video of the target (the lab floor in this case) was then compared with a simulated target. This simulated target was assumed to be a blackbody at emissivity of .95 degrees and the temperature was assumed to be at ambient temperature as recorded by the TIMS for each scanline. Using the slope and the intercept the flux corresponding to this target was converted into digital counts. The counts were observed to have a strong correlation with the actual video as recorded by the TIMS. The attached graphs describe the performance of the TIMS when compressed air is blown at each one of the blackbodies at different speeds. The effect of blowing a fan and changing the room temperature is also being analyzed. Results indicate that the TIMS system responds to variation in wind speed in real time and maintains the capability to produce accurate temperatures on a scan line basis.

Jaggi, S.↗

NASA NTRS1992

Optical design for the ATLAS multispectral scanner

The Airborne Terrestrial Applications Sensor (ATLAS) system is a 15-channel imager for remote sensing applications currently under development at the NASA Stennis Space Center. This paper describes the optical design of the scan head optics, which include the linescan mirror, Dall-Kirkham telescope, collimator, and three spectrometers. The sensor package has a 7.5-inch entrance aperture with a 2.0 mrad ifov, total field of view of 73 degrees, and scan rates adjustable in the range 6-50 rev/sec. The three spectrometers have a modular design for future applications growth. Design and specifications for the telescope, special dichroics, gratings, imaging lenses, and other components for the spectrometers are described. Detector arrays for the three spectrometers, and built-in sources for radiometric calibration, will also be discussed. Finally, results of overall ATLAS systems performance analysis on optical throughput, SNR and NETD are presented.

Damommio, T.↗