Engineering topics
Kuperman, Igor
Publications and source records attributed to Kuperman, Igor.
Ka-band High-Rate Downlink System for the NISAR Mission
This paper provides a description and analyses of the high-rate Ka-band telecom system for the upcoming NISAR (NASA-ISRO Synthetic Aperture Radar) mission. NISAR is a collaborative Earth-Science mission between National Aeronautics and Space Administration (NASA) and Indian Space Research Organization (ISRO), which features an L-band SAR instrument and an S-band SAR instrument. The simultaneous dual-frequency radar system at peak rates will produce data at gigabit-per-second speeds, which drives the data-volume requirements. The key driving requirement for the payload communication subsystem is to provide a minimum of 26 Terabits per day of radar science data to the ground. The high-rate transmitter on the flight system is a software-defined radio developed at the Jet Propulsion Laboratory (JPL), based on the Universal Space Transponder platform, providing an offset quadrature phase shift key modulated waveform with Low-Density Parity-Check encoding of the data transfer frames. Two transmitters used in a dual-polarization configuration with each transmitter providing two giga-symbols per second (Gsps) of coded data provides an aggregate rate of four Gsps. In this system, only one watt of signal power is necessary on each polarization to overcome propagation losses and achieve a successful RF link. Several Near Earth Network (NEN) ground station sites (Alaska in the United States, Svalbard in Norway, and Punta Arenas in Chile) are baselined for the space-to-Earth communications link. Each ground station will also feature multiple upgrades to support NISAR’s transmission starting with new Ka-band antennas, wideband downconverters and high-rate receivers. In addition, a baseband data processor called Data Acquisition Processor and Handling Network Environment (DAPHNE), newly developed by the NEN, provides data storage and connectivity to backhaul networks. With NISAR’s large quantities of data (over 3.5 Petabytes over the mission), the processing of science data will be primarily performed on a cloud system to reduce the overall cost to the mission. The system described herein will be the first operational use of Gsps-class downlink rates on an Earth-Science mission.
High-Rate Ka-Band Modulator for the NISAR Mission
In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.
Relay Communications Support to the ExoMars Schiaparelli Lander
The European Space Agency’s ExoMars Trace Gas Orbiter (TGO) arrived at Mars on October 19, 2016, three days after releasing the Schiaparelli Lander on a ballistic trajectory to Meridiani Planum. During the separation event, and subsequently during Schiaparelli’s Entry, Descent, and Landing (EDL), the NASA-provided Electra UHF payload onboard TGO was used to record signals from the Schiaparelli Lander for post-processing on the ground to recover both tracking of the lander’s carrier signal and reconstruction of the lander’s 8 kb/s telemetry. In addition, ESA’s Mars Express orbiter also recorded the Schiaparelli signal, with ground post-processing providing independent tracking of the lander carrier signal, and the Giant Metrewave Radio Telescope near Pune, India was configured to provide real-time detection of the lander carrier signal. While an anomaly in the latter stages of EDL led to loss of the lander, these critical event data sets, and in particular the telemetry reconstruction enabled by the TGO Electra recording, proved essential in enabling detailed diagnosis of the anomaly. And while the loss of the lander during EDL precluded the planned surface relay operations, the preparations for that activity provide important lessons learned for future Mars relay support scenarios.
The Universal Space Transponder: A Next Generation Software Defined Radio
The Universal Space Transponder (UST) is a next generation transponder developed at the Jet Propulsion Laboratory to meet a large variety of telecom, navigation, and radio science needs for future deep-space and near-Earth missions. This paper details the UST software defined radio design and describes how the combination of a modular hardware architecture and in-flight reprogrammability enables a new level of flexibility and expandability for a space transponder. The UST uses common power and digital processing assemblies that can be integrated with a variety of RF modules and is capable of simultaneous, multiband operations with data rates up to 37.5 Mbps RX and 300 Mbps TX. This allows a single radio to support all the direct-to-Earth and relay communication requirements for even complex mission scenarios, reducing the total cost, mass, and power. The discussion includes a description of the current UST engineering models that have been built and tested, as well as details about the next generation capabilities supported by UST, including advanced link coding and modulation, radiometric techniques, and in-radio protocol handling. Details are also presented on RF modules and digital processing in development for radio science and astronomy purposes, including a bistatic radar receiver and broadband planetary emissions receiver. These will demonstrate the ability to integrate low-cost science instruments into the UST architecture, further expanding the versatility of the UST.
Measuring Input Thresholds on an Existing Board
A critical PECL (positive emitter-coupled logic) interface to Xilinx interface needed to be changed on an existing flight board. The new Xilinx input interface used a CMOS (complementary metal-oxide semiconductor) type of input, and the driver could meet its thresholds typically, but not in worst-case, according to the data sheet. The previous interface had been based on comparison with an external reference, but the CMOS input is based on comparison with an internal divider from the power supply. A way to measure what the exact input threshold was for this device for 64 inputs on a flight board was needed. The measurement technique allowed an accurate measurement of the voltage required to switch a Xilinx input from high to low for each of the 64 lines, while only probing two of them. Directly driving an external voltage was considered too risky, and tests done on any other unit could not be used to qualify the flight board. The two lines directly probed gave an absolute voltage threshold calibration, while data collected on the remaining 62 lines without probing gave relative measurements that could be used to identify any outliers. The PECL interface was forced to a long-period square wave by driving a saturated square wave into the ADC (analog to digital converter). The active pull-down circuit was turned off, causing each line to rise rapidly and fall slowly according to the input s weak pull-down circuitry. The fall time shows up as a change in the pulse width of the signal ready by the Xilinx. This change in pulse width is a function of capacitance, pulldown current, and input threshold. Capacitance was known from the different trace lengths, plus a gate input capacitance, which is the same for all inputs. The pull-down current is the same for all inputs including the two that are probed directly. The data was combined, and the Excel solver tool was used to find input thresholds for the 62 lines. This was repeated over different supply voltages and temperatures to show that the interface had voltage margin under all worst case conditions. Gate input thresholds are normally measured at the manufacturer when the device is on a chip tester. A key function of this machine was duplicated on an existing flight board with no modifications to the nets to be tested, with the exception of changes in the FPGA program.