Search NASA⌕ Search

Engineering topics

Kusse, B. R.

Publications and source records attributed to Kusse, B. R..

At least 19 records

Study of Shock Formation Parameters With Drive Conditions in Magnetically Accelerated Plasma Flows

We present experimental data regarding the formation of high-energy-density shocks in magnetically accelerated plasma flows using pulsed power drivers. We quantify the flow velocity and temperature of the ablated plasma using optical Thomson scattering and gated emission imaging across two different generators. We show that, regardless of the drive parameters, the plasma flows show continuous acceleration over centimeter spatial scales, in line with trends in published simulation work. When stationary targets are placed in these supersonic flows, bow-shock formation is observed at all drive parameters in a range of materials. In the higher density flow generated on the 1-MA COBRA generator at Cornell University, heating of the upstream flow ahead of the shock is observed and quantified, which is not observed at the lower density flow on the 0.2-MA Bertha driver at UC San Diego. Here, when combined with previous work on the XP generator at Cornell, we can show that these three experimental setups allow control of the effect of radiation loss and upstream absorption on the formation of the bow shock.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Axial confinement of wire array Z-pinch precursor plasmas by a pulsed magnetic mirror field

A novel wire-array Z-pinch platform has been developed to study the effect of a pulsed magnetic mirror field on a collisional high energy density plasma. The mirror is driven in series with the Z-pinch target and, therefore, scales with driver current. Axial confinement is observed based on visible imaging and axial flow velocity measurements. The presence of axial compressing J xB force is determined indirectly based on Thomson scattering and interferometry measurements and corroborated by three-dimensional extended-MHD simulations. Compared to non-magnetized wire array Z-pinch, a modified pulsed mirror configuration is observed to increase precursor plasma thermal energy density by about 30%. If optimized, such a configuration could potentially improve magnetized liner inertial fusion performance by reducing axial plasma end loss.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of the imploding plasma sheath in triple-nozzle gas-puff z pinches

Gas-puff z-pinch implosions are characterized by the formation of a dense annular plasma shell, the sheath, that is driven to the axis by magnetic forces and therefore subject to the magneto-Rayleigh–Taylor instability. Here, the conditions within these sheaths are measured on the 1-MA COBRA generator at Cornell University for various gas species and initial fill densities. The gas-puff loads are initialized by a 7 cm diameter triple-nozzle gas valve assembly with concentric outer and inner annular nozzles and a central gas jet. Thomson scattering and laser interferometry provide spatially resolved flow, temperature, and electron density profiles midway through the implosion, while extreme ultraviolet pinhole cameras record the evolution of the plasma column and photoconducting diodes measure x-ray emission. Analysis of the scattering spectra includes a means of discriminating between thermal and non-thermal broadening to test for the presence of hydrodynamic turbulence. Two types of sheath profiles are observed, those with sharp discontinuities at the leading edge and those with smooth gradients. In both cases, non-thermal broadening is generally peaked at the front of the sheath and exhibits a characteristic decay length that roughly scales with the sheath ion mean free path. Here, we demonstrate that this non-thermal broadening term is inconsistent with laminar velocity gradients and is more consistent with dissipative turbulence driven by unstable plasma waves in a collisionless shock. The resulting differences in sheath profile are then set by the sheath ion collisionality in a manner consistent with recent 1D kinetic simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Liner implosion experiments driven by a dynamic screw pinch

This paper expands upon recent experimental results [Campbell et al., Phys. Rev. Lett. 125, 035001 (2020)], where thin-foil liner implosions were driven by a dynamic screw pinch (DSP) and found to have magneto-Rayleigh–Taylor instability (MRTI) amplitudes up to three times smaller than in implosions driven by a standard z-pinch (SZP). Here, the expanded discussion presented herein includes: (1) a detailed comparison of the MRTI growth measured in the experiment with that calculated from theory; (2) measurements of axial magnetic field injection into the liner interior prior to the implosion, as well as the subsequent compression of this field during the implosion; (3) an in-depth description of how the helical geometry of the DSP can result in earlier implosion and stagnation times relative to the SZP; and (4) particle-in-cell simulations showing different electron drift behavior in the anode–cathode gap of the DSP relative to the SZP, and how this difference may be related to the different current waveforms recorded during the experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Current polarity effects on laboratory plasma jets

Plasma jets produced by a pulsed power machine were investigated using Thomson scattering and other diagnostics in order to make detailed comparisons to simulations. These jets were produced from a 15 μm thick disc of Al foil on a 1.2 MA, 100 ns rise time, pulsed power machine. Experiments were performed with both a radially inward and a radially outward current ow in the Al foil to investigate the effects of voltage polarity in the experiments and determine how extended magnetohydrodynamic (XMHD) effects, such as the Hall effect, change the formation of the jet. We recorded Thomson scattering spectra with a low enough laser energy to not perturb the plasma, while providing a high enough signal to noise ratio to resolve the scattered features. This enabled the measurement of the electron temperature in the jet region of the plasma, 15.5±4 eV for both current polarities. Jets with a radially outward current ow were heated more from inverse bremsstrahlung when 10 J of laser energy was used, implying that these jets are denser than the ones with a radially inward current. This higher density was con rmed by interferometry measurements. Experimental results were compared with XMHD computer simulations, which predicted electron temperatures 1.5 to 3 σ above those measured, and significantly higher density than experiments in both polarities. In this paper, possible sources of this discrepancy are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion dynamics of triple-nozzle gas-puff z pinches on COBRA

Experiments on the 1-MA, 220-ns COBRA generator at Cornell University were conducted to provide detailed measurements of structured cylindrical gas-puff z pinches. In the experiments, a 7 cm diameter triple-nozzle gas valve assembly with concentric outer and inner annular nozzles and a central gas jet initialize the z-pinch load with various working gases, radial density profiles, and externally applied axial magnetic fields. Planar laser-induced fluorescence provides a measure of the initial neutral gas density of the load, while three-frame laser shearing interferometry and multi-frame extreme ultraviolet (XUV) cameras reveal the formation and propagation of a magneto-Rayleigh–Taylor (MRT) unstable shock layer. Implosion trajectories are compared to simple, experimentally informed models and found to be in good agreement. Differences in the structure of the accelerating plasma sheath and evolution of the MRT instability are observed for different gas species and axial magnetic field strengths, correlating with differences in pinch uniformity and x-ray emission. Here, the average instability growth is compared to linear MRT theory predictions using the instantaneous acceleration of the best-fit implosion models and characteristic instability wavelength, with the effective Atwood number and seed perturbation size as fit parameters. For high density argon center jets, ionization prior to the arrival of the imploding plasma sheath suggests a heating mechanism consistent with photoionization by XUV self-emission.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stabilization of Liner Implosions via a Dynamic Screw Pinch

Magnetically driven implosions are susceptible to magnetohydrodynamic instabilities, including the magneto-Rayleigh-Taylor instability (MRTI). To reduce MRTI growth in solid-metal liner implo-sions, the use of a dynamic screw pinch (DSP) has been proposed [P. F. Schmit et al., Phys. Rev. Lett. 117, 205001 (2016)]. In a DSP con guration, a helical return-current structure surrounds the liner, resulting in a helical magnetic eld that drives the implosion. Here, we present the rst experimental tests of a solid-metal liner implosion driven by a DSP. Using the 1-MA, 100{200-ns COBRA pulsed-power driver, we tested three DSP cases (with peak axial magnetic elds of 2 T, 14 T, and 20 T) and a standard z-pinch (SZP) case (with a straight return-current structure and thus zero axial eld). The liners had an initial radius of 3.2 mm and were made from 650-nm-thick aluminum foil. Images collected during the experiments reveal that helical MRTI modes developed in the DSP cases, while non-helical (azimuthally symmetric) MRTI modes developed in the SZP case. Additionally, the MRTI amplitudes for the 14-T and 20-T DSP cases were smaller than in the SZP case. Speci cally, when the liner had imploded to half of its initial radius, the MRTI amplitudes for the SZP case and for the 14-T and 20-T DSP cases were, respectively, 1.1-0.3 mm, 0.7-0.2 mm, and 0.3-0.1 mm. Relative to the SZP, the stabilization obtained using the DSP agrees reasonably well with theoretical estimates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electron plasma wave Thomson scattering on laboratory plasma jets

Plasma jets created from a 15 lm thick Al foil on a 1 MA pulsed power machine were studied using a new electron plasma wave (EPW) Thomson scattering system in conjunction with previously developed ion acoustic wave (IAW) Thomson scattering and interferometry. These diagnostics give multiple ways of measuring the electron temperature and density of the jet. Analysis of the EPW feature found the on-axis density of the jet to be between 5 X 10 18 and 1.4 X 10 19 cm -3 , which either matched or was higher than interferometry measurements. Outside of the jet, both of these diagnostics measured a density of 7 X 10 17 cm -3 . On one shot, the EPW spectral feature showed two pairs of peaks within a 250 lm scattering length on the edge of the jet, which shows that the boundary of the jet ~1 mm radius jet is 0.1 mm. While electron temperature measurements of the plasma jet are complicated by the probe beam producing inverse bremsstrahlung heating of the jet, comparison of the electron temperature measured between IAW and EPW Thomson scattering showed the EPW feature to imply significantly higher electron temperatures than the IAW feature (e.g., 160 eV vs 70 eV in one case). Various sources of this discrepancy (for example, density gradients, collisions, and a lag in ionization) and their impact on the plasma are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of Triple Ar Gas Puff Z-Pinches on 0.9-MA, 200-ns COBRA

Ar gas puff z-pinch experiments were conducted on the 0.9 MA, 200 ns COBRA generator at Cornell University. In the experiments, a triple-nozzle gas valve was used to produce the zpinch load with concentric outer and inner gas puffs and a central gas jet. We used Planer Laser Induced Fluorescence (PLIF) to measure the initial gas profile of the load, two 4-frame 4-ns gated XUV cameras to image the imploding plasma, and filtered Photo- Conducting Diamond Detectors (PCDs) to measure the x-ray output. We have observed shock heating and/or photoionization of the dense center jet by the imploding plasma. With an outer to inner plenum pressure ratio of 1:3, de-acceleration of the imploding plasma occurred when the outer plasma shell imploded on the inner shell resulting in a stable implosion. By varying the plenum pressure for the center jet, the x-ray emission was optimized. In conclusion, an Ar K-shell x-ray (3-4 keV) yield of 77±17 J was produced at a current level of 0.87±0.2 MA and an implosion time of 200-ns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multi-angle multi-pulse time-resolved Thomson scattering on laboratory plasma jets

A single channel sub-nanosecond time-resolved Thomson scattering system used for pulsed power-driven high energy density plasma measurements has been upgraded to give electron temperatures at two different times and from two different angles simultaneously. This system was used here to study plasma jets created from a 15 μm thick radial Al foil load on a 1 MA pulsed power machine. Two laser pulses were generated by splitting the initial 2.3 ns duration, 10 J, 526.5 nm laser beam into two pulses, each with 2.5 J, and delaying one relative to the other by between 3 and 14 ns. Time resolution within each pulse was obtained using a streak camera to record the scattered spectra from the two beams from two scattering angles. Analysis of the scattering profile showed that the electron temperature of the Al jet increased from 20 eV up to as much as 45 eV within about 2 ns by inverse bremsstrahlung for both laser pulses. The Thomson scattering results from jets formed with opposite current polarities showed different laser heating of the electrons, as well as possibly different ion temperatures. The two-angle scattering determined that the electron density of the plasma jet was at least 2 × 10 18 cm -3 .

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Time-Resolved Thomson Scattering on Gas-Puff Z-Pinch Plasmas at Pinch Time

The conditions and dynamics of neon gas puff Z-pinch plasmas at pinch time are studied on a pulsed power generator with a current rise time of approximately 200-ns and 0.9-mA peak current. Radial tailoring of the gas puff massdensity profile using a triple-nozzle coaxial valve (two annular gas liners and a central jet) allows production of both more stable and less stable (with regard to the magneto-Rayleigh– Taylor instability) Z-pinch implosions. A 526.5-nm, 10-J Thomson scattering diagnostic laser enables probing of the flow dynamics and plasma conditions of these implosions with both spatial and temporal resolutions. The 2.2-ns laser pulse scatters from the plasma electrons and is carried by one optical fiber to a visible light streak camera, and by a bundle of optical fibers to a time-gated camera, both after spectral dispersion by 750-mm spectrometers. The streak camera, with a 10-ns full streak time, provides subnanosecond resolution of the evolution of the pinch plasma parameters through stagnation. The timegated camera provides spatially resolved spectra (across a field of view of 6.1 mm) at the same time as the streak. Scattering spectra suggest that temperatures are high at stagnation, with the ion temperature as much as three times higher than the electron temperature. Furthermore, we consider the possibility of nonthermal explanations for the broad scattering spectra and high effective ion temperature, including collisionality, implosion velocity distributions (velocity gradients), and small-scale hydrodynamic motion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Observations of the magneto-Rayleigh-Taylor instability and shock dynamics in gas-puff Z-pinch experiments

Here, we describe a series of experiments performed to study the shock structure generated during the implosion of a gas-puff Z-pinch. The Z-pinch is produced by a double-annular gas-puff with a center jet driven by Cornell University's COBRA generator operating with a 1 MA, 200 ns current pulse. Using 532 nm laser interferometry and 100 MHz multi-frame cameras, a shock structure is observed to form early in the implosion. The shock appears to be created by a current layer at the outer radius of the imploding plasma which acts as a piston moving inward at several hundred km s –1 . The dynamics of the shock and its radial position ahead of the piston agree well with a simple uniform density model outlined in the study by Potter [Nucl. Fusion 18(6), 813 (1978)]. The outer surface of the current layer is observed to be Magneto-Rayleigh-Taylor unstable. The growth rate of this instability is found to depend on the radial density profile of the material within the layer of high-density fluid between the shock and the piston, as predicted by recent theoretical work [see, e.g., D. Livescu, Phys. Fluids 16(1), 118 (2004)]. Growth rates measured in krypton implosions, where the post-shock material is found to decay quasi-exponentially away from the piston, were more than ten times smaller than those recorded in otherwise identical implosions in argon plasmas, where the material between the shock and the piston was observed to maintain a uniform density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Time-Resolved Thomson Scattering on Laboratory Plasma Jets

In this study, Thomson scattering measurements were performed on plasma jets created from a 15-μm-thick radial Al foil load on a 1-MA pulsed power machine. The laser used for these measurements has a maximum energy of 10 J at 526.5 nm. Using the full energy, however, significantly heats the 5x10¹⁸ cm⁻³ jet by inverse bremsstrahlung, creating a density bubble in the jet. To measure the evolving plasma parameters of this laser-heated jet, a streak camera was used to record the scattered spectrum, resulting in the sub-ns time-resolved Thomson scattering. Analysis of the streak camera image showed that the electron temperature of the jet was about 25 eV prior to the laser pulse. The laser then heated the plasma to 80-100 eV within about 2 ns. The electron temperature then stabilized for about 0.5 ns prior to falling at the end of the laser pulse. Jets made from a radial Ti foil showed more heating by the laser than the Al jets, going from 50 to over 150 eV, and heating was detected even when only 1 J of laser energy was used. Also, the ion-acoustic peaks in the scattered spectrum from the Ti jets were significantly narrower than those from Al jets, a result of several possible differences in the plasma created from these two materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The Role of Ion Acoustic Instability in the Development of the Azimuthal Current Density Profile in Liner Experiments at 1 MA

Recent work reported on the current density in pulsed-power-driven liners where a vacuum gap was introduced in the power feed connecting the liner to the generator. The resultant gap flashover generates azimuthally localized current-carrying plasma channels, which can create an azimuthal nonuniformity in the current density. The current density evolves during the current pulse, but nonuniformity is observed through the experiment timescale. Magnetohydrodynamic simulation work in 3-D demonstrates the difficulty in reproducing the experimental data within a limited computational domain, and those boundary conditions may dominate this paper. Furthermore, the development of current-driven instabilities in the plasma channels can explain the liner current density evolution, and specifically the ion acoustic instability can account for the main features observed in the experiments.

36 MATERIALS SCIENCE↗

Applied axial magnetic field effects on laboratory plasma jets: Density hollowing, field compression, and azimuthal rotation

We experimentally measure the effects of an applied axial magnetic field (B z ) on laboratory plasma jets and compare experimental results with numerical simulations using an extended magnetohydrodynamics code. A 1 MA peak current, 100 ns rise time pulse power machine is used to generate the plasma jet. On application of the axial field, we observe on-axis density hollowing and a conical formation of the jet using interferometry, compression of the applied B z using magnetic B-dot probes, and azimuthal rotation of the jet using Thomson scattering. Experimentally, we find densities ≤ 5×10 17 cm -3 on-axis relative to jet densities of ≥ 3×10 18 cm -3 . For aluminum jets, 6.5 ± 0.5 mm above the foil, we find on-axis compression of the applied 1.0 ± 0.1 T B z to a total 2.4 ± 0.3 T, while simulations predict a peak compression to a total 3.4 T at the same location. On the aluminum jet boundary, we find ion azimuthal rotation velocities of 15-20 km/s, while simulations predict 14 km/s at the density peak. We discuss possible sources of discrepancy between the experiments and simulations, including: surface plasma on B-dot probes, optical fiber spatial resolution, simulation density floors, and 2D vs. 3D simulation effects. Lastly, this quantitative comparison between experiments and numerical simulations helps elucidate the underlying physics that determine the plasma dynamics of magnetized plasma jets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of the time-resolved, 3-dimensional current density distribution in solid metallic liners at 1 MA

We present a study of the time varying current density distribution in solid metallic liner experiments at the 1MA level. Measurements are taken using an array of magnetic field probes which provide 2D triangulation of the average centroid of the drive current in the load at 3 discrete axial positions. These data are correlated with gated optical self-emission imaging which directly images the breakdown and plasma formation region. Results show that the current density is azimuthally non-uniform, and changes significantly throughout the 100ns experimental timescale. Magnetic field probes show clearly motion of the current density around the liner azimuth over 10ns timescales. If breakdown is initiated at one azimuthal location, the current density remains non-uniform even over large spatial extents throughout the current drive. The evolution timescales are suggestive of a resistive diffusion process or uneven current distributions among simultaneously formed but discrete plasma conduction paths.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Helical plasma striations in liners in the presence of an external axial magnetic field

Awe et al. found on the 20 MA Z machine [Acta Phys. Pol. A 115, 956 (2009)] that applying an externally generated axial magnetic field to an imploding liner leads to a helical pattern in the liner when viewed with soft x-ray radiography ([Phys. Rev. Lett. 111, 235005 (2013)] and [Phys. Plasmas 21, 056303 (2014)]). We show that this phenomenon is also observed in extreme ultraviolet self-emission images of 10 mm long cylindrical metal liners having varying diameters and varying wall thicknesses on a 1 MA, 100–200 ns pulsed power generator. The magnetic field in these experiments is created using either twisted return current wires positioned close to the liner, generating a time-varying B z , or a Helmholtz coil, generating a steady-state B z .

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Investigation of the effect of a power feed vacuum gap in solid liner experiments at 1 MA

We present an experimental study of plasma initiation of a solid metal liner at the 1 MA level. In contrast to previous work, we introduce a vacuum gap at one of the liner connections to the power feed to investigate how this affects plasma initiation and to infer how this may affect the symmetry of the liner in compression experiments. We observed that the vacuum gap causes non-uniform plasma initiation both azimuthally and axially in liners, diagnosed by gated optical imaging. Using magnetic field probes external to the liner, we also determined that the optical emission is strongly linked to the current distribution in the liner. The apparent persistent of azimuthal non-uniformities may have implications for fusion-scale liner experiments.

Bott-Suzuki, S. C.↗