Engineering topics

Kwon, Dong-Soo

Publications and source records attributed to Kwon, Dong-Soo.

6 records

NASA NTRS1991

Control of a flexible bracing manipulator: Integration of current research work to realize the bracing manipulator

All research results about flexible manipulator control were integrated to show a control scenario of a bracing manipulator. First, dynamic analysis of a flexible manipulator was done for modeling. Second, from the dynamic model, the inverse dynamic equation was derived, and the time domain inverse dynamic method was proposed for the calculation of the feedforward torque and the desired flexible coordinate trajectories. Third, a tracking controller was designed by combining the inverse dynamic feedforward control with the joint feedback control. The control scheme was applied to the tip position control of a single link flexible manipulator for zero and non-zero initial condition cases. Finally, the contact control scheme was added to the position tracking control. A control scenario of a bracing manipulator is provided and evaluated through simulation and experiment on a single link flexible manipulator.

Kwon, Dong-Soo↗

NASA NTRS1991

Control of a flexible bracing manipulator

Many applications of robotic manipulator arms require operation in contact and noncontact regimes. Control of impact between the arm's tip and the environment has been largely ignored in prior research. The impact phenomena was investigated through simulation and experiment for the realization of the bracing strategy, and the key factors of the behavior were understood well. The approaching velocity is dominant parameter for the magnitude of the impact force. The impact is also affected by the compliance of the environmental surface.

Kwon, Dong-Soo↗

NASA NTRS1991

Contact control for advanced applications of light weight arms

Many applications of robotic and teleoperated manipulator arms require operation in contact and non-contact regimes. This paper deals with both regimes and the transition between them with special attention given to problems of flexibility in the links and drives. This is referred to as contact control. Inverse dynamics is used to plan the tip motion of the flexible link so that the free motion can stop very near the contact surface without collision due to overshoot. Contact must occur at a very low speed since the high frequency impact forces are too sudden to be affected by any feedback generated torques applied to a joint at the other end of the link. The effect of approach velocity and surface properties are discussed. Force tracking is implemented by commands to the deflection states of the link and the contact force. This enables a natural transition between tip position and tip force control that is not possible when the arm is treated as rigid. The effect of feedback gain, force trajectory, and desired final force are of particular interest and are studied. Experimental results are presented on a one link arm and the system performance in the overall contact task is analyzed. Extension to multi-link cases with potential applications are discussed.

Book, Wayne J.↗

NASA NTRS1991

A time domain inverse dynamic method for the end point tracking control of a flexible manipulator

The inverse dynamic equation of a flexible manipulator was solved in the time domain. By dividing the inverse system equation into the causal part and the anticausal part, we calculated the torque and the trajectories of all state variables for a given end point trajectory. The interpretation of this method in the frequency domain was explained in detail using the two-sided Laplace transform and the convolution integral. The open loop control of the inverse dynamic method shows an excellent result in simulation. For real applications, a practical control strategy is proposed by adding a feedback tracking control loop to the inverse dynamic feedforward control, and its good experimental performance is presented.

Kwon, Dong-Soo↗

NASA NTRS1990

An inverse dynamic method yielding flexible manipulator state trajectories

An inverse dynamic equation for a flexible manipulator is derived in a state form. By dividing the inverse system into the causal part and the anticausal part, torque is calculated in the time domain for a certain end point trajectory, as well as trajectories of all state variables. The open loop control of the inverse dynamic method shows an excellent result in simulation. For practical applications, a control strategy adapting feedback tracking control to the inverse dynamic feedforward control is illustrated, and its good experimental result is presented.

Kwon, Dong-Soo↗

NASA NTRS1990

An inverse dynamic method yielding flexible manipulator state trajectories

An inverse dynamic equation for a flexible manipulator is derived in a state form. By dividing the inverse system into the causal part and the anticausal part, one can calculate torque in the time domain for a certain end-point trajectory, as well as trajectories of all state variables. The open-loop control of the inverse dynamic method shows an excellent result in simulation. For practical applications, a control strategy adapting feedback tracking control to the inverse dynamic feedforward control is illustrated, and experimental results are presented.

Kwon, Dong-Soo↗