Engineering topics

LaBelle, Remi C.

Publications and source records attributed to LaBelle, Remi C..

4 records

NASA NTRS2018

Radio Science System Design and Measurement Results for the NASA Deep Space Network (DSN)

Radio science measurements have been performed using the NASA Deep Space Network (DSN) with many different spacecraft over several decades. Radio science has been used for the study of planetary atmospheres, the solar corona and the search for gravity waves, among other things. The majority of these measurements are made using the X and Ka-band deep space bands. Although the primary mission for the DSN is tracking, telemetry and command (TT&C) for NASA’s many deep-space spacecraft, radio science measurements continue to be an important secondary mission. The science requirements for these measurements have resulted in stringent performance requirements for both the spacecraft and ground system equipment. In particular, the requirements for amplitude stability, phase stability (Allen deviation) and phase noise are very demanding. The system Allen deviation requirement at Ka-band is < 2.4 E-15 over 1000 seconds, while the phase noise requirement is < -50 dBc/Hz for a 1 Hz offset. Various design techniques have been used for the DSN radio frequency (RF) electronics, high power transmitters and antenna structures to meet the stringent requirements for all 3 of these parameters. Some details for the design techniques will be described in the paper. Another important consideration for a radio science system is the verification approach for components, as well as for individual subsystems and then the overall system. Phase-locked oscillators (PLOs) are one of the key component types that determine overall phase noise and Allen deviation system performance. Measurement techniques used for PLOs, as well as for the overall ground system, will be discussed. Measurement results for the 2 new DSN antennas, recently built under the DSN Aperture Enhancement Project (DAEP) will also be shown. In addition, some recent radio science measurements from the Cassini and JUNO missions, using the new antennas, will be presented.

LaBelle, Remi C.↗

NASA NTRS2017

Calibration and Performance Measurements for the NASA Deep Space Network Aperture Enhancement Project (DAEP)

The NASA Deep Space Network (DSN) has recently constructed two new 34-meter antennas at the Canberra Deep Space Communications Complex (CDSCC). These new antennas are part of the larger DAEP project to add six new 34-meter antennas to the DSN, including two in Madrid, three in Canberra and one in Goldstone (California). The DAEP project included development and implementation of several new technologies for the S, X, Ka (26 GHz) and Ka (32 GHz) -band uplink and downlink electronics, as previously reported. The electronics upgrades were driven by several different considerations, including parts obsolescence, cost reduction, improved reliability and maintainability, and capability to meet future performance requirements. The new antennas are required to support TT&C links for all of the NASA deep-space spacecraft, as well as for several international partners. Some of these missions, such as Voyager 1 and 2, have very limited link budgets, which results in demanding requirements for system G/T performance. These antennas are also required to support radio science missions with several spacecraft, which dictate some demanding requirements for spectral purity, amplitude stability and phase stability for both the uplink and downlink electronics. After completion of these upgrades, a comprehensive campaign of tests and measurements took place to characterize the electronics and calibrate the antennas. Radiometric measurement techniques were applied to characterize, calibrate, and optimize the performance of the antenna parameters. These included optical and RF high-resolution holographic and total power radiometry techniques. These techniques, which are described in the article, resulted in the highest antenna aperture efficiency in the DSN, of 66% achieved, at the highest operating frequency of the antenna, which is Ka-Band (32-GHz). The other measurements and results described include antenna noise temperature, photogrammetry and holography alignment of antenna panels, beam-waveguide mirrors, and subreflector, antenna aperture efficiencies and G/T versus frequency, and antenna pointing models. The first antenna (DSS-35) was entered into operations in October, 2014 and the 2nd antenna (DSS-36) in October, 2016. This paper describes the measurement techniques and results of the testing and calibration for both antennas, along with the driving requirements.

Rochblatt, David J.↗

NASA NTRS2003

A 94 GHz RF Electronics Subsystem for the CloudSat Cloud Profiling Radar

The CloudSat spacecraft, scheduled for launch in 2004, will carry the 94 GHz Cloud Profiling Radar (CPR) instrument. The design, assembly and test of the flight Radio Frequency Electronics Subsystem (RFES) for this instrument has been completed and is presented here. The RFES consists of an Upconverter (which includes an Exciter and two Drive Amplifiers (DA's)), a Receiver, and a Transmitter Calibrator assembly. Some key performance parameters of the RFES are as follows: dual 100 mW pulse-modulated drive outputs at 94 GHz, overall Receiver noise figure < 5.0 dB, a highly stable W-band noise source to provide knowledge accuracy of Receiver gain of < 0.4 dB over the 2 year mission life, and a W-band peak power detector to monitor the transmitter output power to within 0.5 dB over life. Some recent monolithic microwave integrated circuit (MMIC) designs were utilized which implement the DA's in 0.1 micron GaAs high electron-mobility transistor (HEMT) technology and the Receiver low-noise amplifier (LNA) in 0.1 micron InP HEMT technology.

radio frequency electronics subsystem (RFES)↗

NASA NTRS2003

A Channelized 2nd IF/LO Downconverter for the E0S Microwave Limb Sounder

The Earth Observing System (EOS) Microwave Limb Sounder (MLS) is scheduled for launch in 2004 on the EOS Aura spacecraft. The design, assembly and test of the flight 2nd Intermediate Frequency/ Local Oscillator (2nd IF/LO) subsystem for this instrument has been completed and is presented here. The 2nd IF/LO subsystem consists of 5 separate microwave assemblies, 1 for each of the 5 millimeter wave radiometer front ends, providing a total of 33 separate IF channels. Some key requirements of the subsystem are as follows: provide frequency multiplexing of overlapping or closely spaced 1st IF channels while maintaining low ripple in the passbands; generate 19 different 2nd LO frequencies, in the range of 4-20 GHz, with low phase noise and a placement resolution of 400 KHz; downconvert the 1st IF's to a common 2nd IF frequency centered at 900 MHz; minimize cost and schedule by using common designs for the 5 different assemblies wherever possible.

intermediate frequency/local oscillator (IF/LO)↗