Latest results from the RD42 collaboration on the radiation tolerance of polycrystalline diamond detectors
Not provided.
Instruments & Instrumentation↗
Engineering topics
Lacoste, A.
Publications and source records attributed to Lacoste, A..
New test beam results of 3D and pad detectors constructed with poly-crystalline CVD diamond
Not provided.
Instruments & Instrumentation↗
Beam test results of 3D pixel detectors constructed with poly-crystalline CVD diamond
As a possible candidate for extremely radiation tolerant tracking devices we present a novel detector design - namely 3D detectors - based on poly-crystalline CVD diamond sensors with a pixel readout. The fabrication of recent 3D detectors as well their results in recent beam tests are presented. We measured the hit efficiency and signal response of two 3D diamond detectors with 50 × 50 μm cell sizes using pixel readout chip technologies currently used at CMS and ATLAS. In all runs, both devices attained efficiencies >98 % in a normal incident test beam of minimum ionising particles. The highest efficiency observed during the beam tests was 99.2 %.
72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
Latest Results on Radiation Tolerance of Diamond Detectors
At present most experiments at the CERN Large Hadron Collider (LHC) are planning upgrades in the next 5-10 years for their innermost tracking layers as well as luminosity monitors to be able to take data as the luminosity increases and CERN moves toward the High Luminosity-LHC (HL-LHC). These upgrades will most likely require more radiation tolerant technologies than exist today. As a result this is one area of intense research, and Chemical Vapour Deposition (CVD) diamond is one such technology. CVD diamond has been used extensively in beam condition monitors as the innermost detectors in the highest radiation areas of all LHC experiments. This talk describes the preliminary radiation tolerance measurements of the highest quality polycrystalline CVD material for a range of proton energies and neutrons obtained with this material with the goal of elucidating the issues that should be addressed for future diamond based detectors. The talk presents the evolution of various semiconductor parameters as a function of dose.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Results on radiation tolerance of diamond detectors
In sight of the luminosity increase of the High Luminosity-LHC (HL-LHC), most experiments at the CERN Large Hadron Collider (LHC) are planning upgrades for their innermost layers in the next 5–10 years. These upgrades will require more radiation tolerant technologies than exist today. Usage of Chemical Vapor Deposition (CVD) diamond as detector material is one of the potentially interesting technologies for the upgrade. CVD diamond has been used extensively in the beam condition monitors of BaBar, Belle, CDF and all LHC experiments. Measurements of the radiation tolerance of the highest quality polycrystalline CVD material for a range of proton energies, pions and neutrons obtained with this material are presented. In addition, new results on the evolution of various semiconductor parameters as a function of the dose rate are described.
46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
Diamond detector technology, status and perspectives
Detectors based on Chemical Vapor Deposition (CVD) diamond have been used extensively and successfully in beam conditions/beam loss monitors as the innermost detectors in the highest radiation areas of Large Hadron Collider (LHC) experiments. The startup of the LHC in 2015 brought a new milestone where the first polycrystalline CVD (pCVD) diamond pixel modules were installed in an LHC experiment and successfully began operation. The RD42 collaboration at CERN is leading the effort to develop polycrystalline CVD diamond as a material for tracking detectors operating in extreme radiation environments. The status of the RD42 project with emphasis on recent beam test results is presented.
3D diamond detectors↗
Ion source development for a photoneutralization based NBI system for fusion reactors
The next step after ITER is to demonstrate the viability and generation of electricity by a future fusion reactor (DEMO). The specifications required to operate an NBI system on DEMO are very demanding. The system has to provide a very high level of power and energy, ~100MW of D° beam at 1MeV, including high wall-plug efficiency (η > 60%). For this purpose, a new injector concept, called Siphore, is under investigation between CEA and French universities. Siphore is based on the stripping of the accelerated negative ions by photo-detachment provided by several Fabry-Perot cavities (3.5MW of light power per cavity) implemented along the D{sup −} beam. The beamline is designed to be tall and narrow in order that the photon flux overlaps the entire negative ion beam. The paper will describe the present R and D at CEA which addresses the development of an ion source and pre-accelerator prototypes for Siphore, the main goal being to produce an intense negative ion beam sheet. The negative ion source Cybele is based on a magnetized plasma column where hot electrons are emitted from the source center. Parametric studies of the source are performed using Langmuir probes in order to characterize the plasma and to compare with numerical models being developed in French universities.
43 PARTICLE ACCELERATORS↗
Multi-dipolar microwave plasmas and their application to negative ion production
During the past decade multi-dipolar plasmas have been employed for various purposes such as surface treatments in biomedicine, physical and chemical vapour deposition for hydrogen storage, and applications in mechanical engineering. On the other hand, due to the design and operational mode of these plasma sources (i.e., strong permanent magnets for the electron cyclotron resonance coupling, low working pressure, and high electron density achieved) they are suitable for studying fundamental mechanisms involved in negative ion sources used in magnetically confined fusion and particle accelerators. Thus, this study presents an overview of fundamental results obtained with: (i) a single dipolar source, (ii) a network of seven dipolar plasma sources inserted into a magnetic multipolar chamber (Camembert III), and (iii) four dipolar sources housed in a smaller metallic cylinder (ROSAE III). Investigations with Langmuir probes of electron energy probability functions revealed the variation of the plasma properties versus the radial distance from the axis of a dipolar source in its mid plane and allowed the determination of the proportion between hot and cold electron populations in both chambers. These results are compared with the density of hydrogen negative ions, measured using the photodetachment technique. Electron energy probability functions obtained in these different configurations show the possibility of both hot and cold electron production. The former is a prerequisite for increasing the vibrational level of molecules and the dissociation degree and the latter for producing negative ions via dissociative attachment of the cold electrons or via surface production induced by H atoms.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗