Search NASA⌕ Search

Engineering topics

Ladshaw, Austin P.

Publications and source records attributed to Ladshaw, Austin P..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Influence of elevated temperature and oxygen on the capture of radioactive iodine by silver functionalized silica aerogel

Reprocessing is considered a competent strategy for spent nuclear fuel management, yet radioiodine ( 129 I) is emitted in reprocessing off-gas as a hazardous byproduct. Silver functionalized silica aerogel (Ag 0 -aerogel), a promising iodine capture material, experiences a reduction in its capacity after prolonged exposure to off-gas components at elevated temperatures, a phenomenon termed as aging. To fully understand this process, we isolated the contribution of each aging factor, exposing Ag 0 -aerogel samples to N 2 and dry air gas streams, respectively, at 150 °C for different time periods. Aged samples were loaded with I 2 to examine the capacity change and comprehensively characterized to investigate the evolution of their properties. Results show that temperature alone did not alter Ag 0 -aerogel's capacity but triggered Ag 0 nanoparticles sintering and generated organic sulfur species. The presence of O 2 reduced the capacity by ~20 %, causing (i) formation of silver sulfide (Ag 2 S) crystals and (ii) oxidation of Ag-thiolate (Ag-S-r) to Ag sulfonate (Ag-SO 3 -r). Given that Ag 2 S readily adsorbs I 2 , the formation of Ag-SO 3 -r is the major inhibitor for iodine adsorption. This hypothesis was supported by density functional theory (DFT) simulations. These findings unraveled key mechanisms of Ag 0 -aerogel aging, which are useful in the development of materials that withstand realistic spent-nuclear-fuel-reprocessing off-gas conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Adsorption of molecular iodine and alkyl iodides from spent-nuclear-fuel-reprocessing off-gas using reduced silver mordenite

Radioactive iodine is a hazardous byproduct of spent-nuclear-fuel reprocessing that must be removed from the off-gas stream before it can be discharged. Reduced silver mordenite (Ag 0 Z) is currently the baseline material for iodine capture in the U.S. Although the performance characteristics and capture mechanisms of I 2 and CH 3 I have been established, similar investigations into long-chain organic iodides have yet to be performed. In this study, thin beds of Ag 0 Z were loaded with I 2 , CH 3 I, C 4 H 9 I, and C 12 H 25 I (5 ppm to 50 ppm) carried in a dry air stream at 150°C. The maximum iodine capacity was 105 ± 5 mg I/g Ag 0 Z for all species. Saturated Ag 0 Z samples were characterized using scanning electron microscopy, X-ray fluorescence, X-ray photoelectron spectroscopy, diffuse reflectance UV–visible spectroscopy, pair distribution function analysis, and thermogravimetric analysis. Further, near-complete Ag utilization and similar physical/chemical properties were observed for all samples. Through a comparison with previous studies and an investigation of aged Ag 0 Z, we propose that iodine species react with Ag + at exchange sites, forming α-AgI within the mordenite channels, and with surface Ag 0 nanoparticles, yielding β-/γ-AgI. The available Ag sites in the interior (Ag + ) and exterior (Ag 0 ) of mordenite determine the adsorption capacity since α-AgI formation is limited by the total pore volume. Potential iodine uptake routes were summarized for aging and non-aging environments. A scalable predictive model was implemented for deep-bed iodine removal, and predictions were in good agreement with experimental data. Sensitivity analysis suggests that iodine uptake kinetics is governed by pore diffusion.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Simulation of radioactive plume transport in the atmosphere including dynamics of particle aggregation and breakup

Accurate prediction of the atmospheric transport of debris particles relies heavily on our knowledge of the size distribution of the particles within a debris cloud. Assuming a fixed particle size during simulations is not always viable since the size distribution of the debris can change during transport. Various microphysical processes, such as aggregation and breakup, influence debris particles and dictate any changes to the size distribution. To track those changes that can occur, a population balance model can be adopted and instituted within a model framework. Nonetheless, many of the models that simulate the transport of radioactive debris following a device-driven fission incident have historically neglected to consider these processes. As such, this work describes our effort to develop a modeling framework capable of simulating the transport and deposition of a radioactive plume generated from a fission incident with a dynamic population balance including particle aggregation and breakup. Herein the impact of aggregation and breakup, individually and collectively, on the particle size distribution is explored using the developed framework. When simulating aggregation, for example, six mechanisms, including Brownian coagulation, the convective enhancement to Brownian coagulation, van der Waals-viscous force correction for Brownian coagulation, gravitational collection, turbulent inertial motion, and turbulent shear, are considered. Brownian coagulation and its corrections have, as one would expect, a large impact on relatively small aggregates. Aggregates with a diameter that is less than or equal to 1.0 μm, for instance, comprise 50.6 vol % of all aggregates in the absence of aggregation and 31.2 vol % when Brownian coagulation and its corrections are considered. Gravitational collection and, to a much lesser extent, turbulent shear and turbulent inertial motion are, conversely, of great importance to relatively large aggregates (i.e., diameter greater than 3.0 μm). Additionally, the individual effects of atmospheric and particle parameters, such as wind speed and particle density, are examined. Of the parameters examined, turbulent energy dissipation and aggregate fractal dimension (i.e., aggregate shape with lower values representing more irregular particles) were of substantial importance since both terms directly impact aggregate stability and, by extension, the breakup rate. Large-scale transport and deposition simulations in a dry atmosphere are also presented and discussed as a proof of concept.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

Capture of Organic Iodides from Vessel Off-Gas Streams

In nuclear waste reprocessing, radioactive iodine is released in both organic and inorganic forms into off-gas streams. Due to its properties of long half-life and potential accumulation in human bodies, radioactive iodine is required to be removed from off-gas streams by the Environmental Protection Agency (EPA) and Nuclear Regulatory Commission (NRC). In this study, the removal of organic iodides using two prototype silver (Ag) adsorbents, i.e., reduced Ag functionalized silica aerogel (Ag 0 -aerogel) and reduced Ag exchanged mordenite (Ag 0 Z), is investigated through a combination of experimental and modeling studies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Experiments and modeling to evaluate global reaction kinetics of three-way catalyst light off for net-zero carbon fuels and selected fuel blends

Internal combustion engine exhaust composition can have a significant impact on the light-off characteristics of CO, NO, and organics in the three-way-catalyst during cold-start. The U.S. Department of Energy’s Co-Optimization of Fuels and Engines initiative was aimed at developing new high-performance fuels, which raises the question of how current three-way-catalysts will perform if the exhaust composition is significantly changed. This work is aimed at quantifying the performance of the catalyst under a variety of different fuel components and mixtures. To this end, a reduced-order model is developed wherein the set of organics examined are placed into molecular groups based on their reactivities and to model each organic within that group with a common kinetic expression. In conclusion, this strategy allows for a first approximation to the light-off characteristics of all organics that fall within that group and to make predictions for fuel blends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Models to Incorporate Reaction Mechanisms into DG-OSPREY: Fixed-Bed Simulations for Organic Iodides Capture Using Ag 0 Z

As one of the most potent radioisotopes released during spent nuclear fuel reprocessing, 129 I is strictly regulated and must be removed before discharge. Organic iodides (primarily alkyl iodides with different chain lengths, i.e., CH 3 I, C 4 H 9 I, and C 12 H 25 I) comprise ~2% of the total iodine in the reprocessing off-gases and are primarily present in vessel off-gas (VOG). Reduced silver mordenite (Ag 0 Z) is predominantly considered for the removal of radioiodine; however, its capture performance and underlying interaction processes with long-chain organic iodides are not fully understood. Two major tasks were accomplished in this study. First, to improve upon the previous experimental studies where Ag 0 Z was used to capture CH 3 I, C 4 H 9 I, and C 12 H 25 I at different concentrations, we comprehensively investigated the corresponding capture mechanisms by characterizing fully loaded Ag 0 Z samples. Second, computational codes were implemented to perform fixed-bed simulations that account for transport and reaction mechanisms. Scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX), powder X-ray diffraction (PXRD), UV-visible diffuse reflectance spectroscopy (UV-vis DRS), and thermogravimetric analysis (TGA) were conducted on Ag 0 Z samples that are saturated with I 2 , CH 3 I, C 4 H 9 I, and C 12 H 25 I), respectively. Results indicate that AgI is the predominant adsorption product regardless of the adsorbed iodine species, yet alkyl iodides with different carbon chain lengths may have different compositions of α- and γ-AgI. Synchrotron pair distribution function (PDF) measurements and TGA coupled with a Fourier transformed infrared detector (TGA FTIR) have been performed, and experimental data are currently analyzed. Results are expected to provide further insights into the adsorption mechanisms. The fixed-bed capture performance for CH 3 I was successfully simulated by solving mathematical equations that describe the underlying transport processes and adsorption reactions. The computational framework, Catalytic After Treatment System (CATS), that was originated in our research group, was used to solve the governing equations. Kinetic parameters, including the pore diffusivity and reaction rate constant were obtained by optimization techniques using data from thin-bed experiments performed at Oak Ridge National Laboratory. The performance of a deep bed predicted using the optimized parameters showed promising agreement with the experimental data.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Charging of radioactive and environmental airborne particles

The charging of various airborne particles was investigated using single-particle levitation and charge-balance equations. Though radioactive decay and triboelectrification can induce charging, it is typically assumed that the aerosols in a radioactive plume will not carry significant charge at steady state since atmospheric particles can have their charge neutralized through the capture of adjacent counter-ions (i.e., diffusion charging). Here to assess this assumption, we directly measured the surface charge and charge density of various triboelectrically charged aerosols including radioactive uranium oxide (<1 μm), urban dust, Arizona desert dust, hydrophilic and hydrophobic silica nanoparticles, and graphene oxide powders using an electric field-assisted particle levitator in air. Of these particles, uranium oxide aerosols exhibited the highest surface charge density. Charge balance equations were employed to predict the average charge gained from radioactive decay as a function of time and to evaluate the effects of diffusion charging on triboelectrically charged radioactive and non-radioactive particles in the atmosphere. Simulation results show that particles, initially charged through triboelectrification, can be quickly discharged by diffusion charging in the absence of radioactive decay. Nevertheless, simulation results also indicate that particles can be strongly charged when they carry radionuclides. These experimental and simulation results suggest that radioactive decay can induce strong particle charging that may potentially affect atmospheric transport of airborne radionuclides.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Assessing impact of real-world aging on Cu-redox half cycles of a Cu-SSZ-13 SCR catalyst via transient response measurements and kinetic modeling

We report that the SCR reaction on Cu-SSZ-13 is a redox process consisting of a reduction half-cycle (RHC) and an oxidation half-cycle (OHC). Despite extensive efforts to understand hydrothermal aging and sulfur poisoning, the impact of real-world aging on the SCR activity of Cu-SSZ-13 has not been reported. This work employs a transient response methodology consisting of experiments and kinetic models to investigate the SCR redox cycles at intra-catalyst locations of commercial Cu-SSZ-13 monolith catalysts in their degreened and real-world aged states, in the temperature range of 200–450 °C. Moreover, H 2 -TPR, NH 3 -TPD, SO 2 -TPD, ICP-OES and solid-state NMR were performed to investigate the catalyst properties. Sulfur aging and dealumination caused by real-world exposure decreased the reducible Cu density and SCR performance. Real-world aging was found to selectively slow OHC more than RHC, mainly due to lower mobility of the Cu ions coordinated to sulfur-related species leading to decreased formation of Cu-dimers necessary for OHC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

A Transient-Response methodology based on experiments and modeling for Cu-Redox Half-Cycle kinetic analysis on a Cu-SSZ-13 SCR catalyst

In this report the Standard SCR reaction catalyzed by Cu-SSZ-13 is a redox process consisting of a reduction half cycle (RHC) and an oxidation half cycle (OHC) that cycle the active Cu sites between the Cu(II) and Cu(I) states. In the current work, a transient-response methodology consisting of experimental transient response Cu-redox (TRCR) measurements and kinetic modeling was developed for detailed study of individual SCR Cu-redox half cycles. The TRCR protocol allows quantification of the reducible Cu density, Cu(II)-Cu(I) partitioning, relative native RHC and OHC rates, and limiting half cycle during SCR. The half-cycle kinetics are studied over a wide (170–450 °C) temperature, and in differential segments along the catalyst length using spatially resolved capillary inlet mass-spectrometry (SpaciMS). The protocol alone provides two independent measures indicating that OHC increases faster than RHC with temperature, and that at all but the lowest temperature SCR is RHC limited. Introducing the transient kinetic models allows half-cycle reaction pathways, orders and activation energies to be studied and determined; e.g., RHC involves surface and gas-phase NH 3 routes, and OHC with O 2 involves dimer formation. Application of the full methodology provides further confirmation and quantification of the protocol conclusions, and specifically the first measurements of RHC and OHC activation energies; specifically for parallel RHC surface and gas-phase routes, and experimentally obtained OHC activation energy vs. first-principle calculations in the literature. Beyond insights related to the degreened catalyst studied here, the methodology provides a broadly available approach for quantifying how aging processes selectively impact RHC and OHC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Mechanistic Understanding of Silver Sorbent Aging Processes in Off-Gas Treatment

The effect of aging in various off-gas streams including dry air, humid air, 1% NO/N 2 , 2% NO 2 /air, and a gas mixture consisting of 99.25% humid air (dew point: -15 °C), 0.25% NO/N 2 , and 0.5% NO 2 /air in terms of concentration on reduced silver exchanged mordenite (Ag 0 Z) and silver functionalized silica aerogel (Ag 0 -aerogel) were studied in this project. Utilizing simple and sophisticated experimental information combined with molecular and macroscopic mechanistic modeling, this project has significantly advanced the current understanding of aging for silver bearing adsorbents in nuclear-fuel-reprocessing off-gas streams. In addition, this project has produced models that can be utilized to predict the influence of adsorbent aging on the uptake kinetics and capacity of aged adsorbents for iodine and iodine-containing organic compounds. The results of the study have been published in the open literature, and can be used to help DOE better predict the removal of radioactive gases from nuclear-fuel-reprocessing off-gas streams.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Capture of Iodine from Nuclear-Fuel-Reprocessing Off-Gas: Influence of Aging on a Reduced Silver Mordenite Adsorbent after Exposure to NO/NO 2

Iodine radioisotopes released during nuclear fuel reprocessing must be removed from the off-gas stream before discharge. One promising material for iodine capture is reduced silver mordenite (Ag 0 Z). Nevertheless, the adsorbent’s capacity will degrade, or age, over time when the material is exposed to other off-gas constituents. Though the overall impact of aging is known, the underlying physical and chemical processes are not. To examine these processes, Ag 0 Z samples were prepared and aged in 2% NO 2 in dry air and in 1% NO in N 2 gas streams at 150 °C for up to six months. Aged samples were then characterized using scanning electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray absorption spectroscopy. These techniques show that aging involves two overarching processes: (i) oxidation of the silver nanoparticles present in Ag 0 Z and (ii) migration of oxidized silver into the mordenite’s inner network. Silver on the nanoparticle’s surface is oxidized through adsorption of O 2 , NO, and NO 2 . Additionally, Raman spectroscopy and X-ray absorption spectroscopy indicate that nitrates are the primary products of this adsorption. Most of these nitrates migrate into the interior of the mordenite and exchange at framework binding sites, returning silver to its unreduced state (AgZ). The remaining nitrates exist at a persistent concentration without aggregating into bulk-phase AgNO 3 . X-ray absorption spectroscopy results further indicate that iodine adsorption occurs on not just Ag 0 Z but also on AgZ and a portion of the nitrates in the system. AgZ adsorbs a sizable quantity of iodine early in the aging process, but its capacity drops rapidly over time. For well-aged samples, nitrates are responsible for up to 95% of mordenite’s iodine capacity. Overall, these results have enhanced our understanding of the aging process in silver mordenite and are expected to guide the development of superior adsorbents for the capture of radioactive iodine from reprocessing off-gas.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Uranium recovery from seawater using amidoxime-based braided polymers synthesized from acrylic fibers

Global demand for nuclear energy is expected to rise in the coming decades. To meet these growing needs, new uranium resources must be explored. One of the potential alternatives to traditional uranium mining is oceanic uranium. The capture and recovery of uranium from the ocean has been under investigation for some time, with many recent studies focused on amidoxime based adsorbents. These adsorbents while able to achieve high uranium recovery capacities are, nevertheless, expensive to produce and adsorb a significant amount of hard to remove vanadium. The purpose of this study is to evaluate the adsorption performance of amidoxime based polymer braids synthesized from acrylic fibers which are designed to significantly cut polymer synthesis and conditioning costs. Adsorption experiments were performed in a recirculating raceway flume system at environmental conditions, approximately 10.8 oC, with 40-micron prefiltered seawater over 28 days for small and large sized LCW polymer braids. For both braid sizes, the adsorption of vanadium was far lower on the LCW materials than on Oak Ridge National Laboratory’s amidoxime based AF1 and AI8 small braids, with the LCW small braids outperforming both materials with respect to uranium adsorption under similar conditions. Adsorption modeling was used to simulate the performance at higher temperatures based on 20oC experiments previously performed with similar materials. Simulation results indicated that the small LCW braids would have a less significant advantage with respect to uranium adsorption over both AF1 and AI8 at 20oC and adsorb slightly less uranium than AF1 at 31oC. Vanadium adsorption by LCW small braids was less than one third of vanadium adsorption by either AF1 or AI8 for all temperatures. This behavior indicates that the LCW materials are able to achieve comparable uranium adsorption to other amidoxime adsorbents previously developed, while being cheaper to produce and adsorbing significantly less vanadium.

Wiechert, Alexander I.↗