Engineering topics

Lahoda, Edward J.

Publications and source records attributed to Lahoda, Edward J..

At least 19 records

DOE OSTI2024

Transient behavior of oxide fuels with controlled microstructure and Cr2O3 additive

Abstract Microstructure and Cr 2 O 3 doping profoundly impact the thermal-mechanical properties and fracture of oxides fuels. It is a challenge to study the transient behavior of nuclear fuels under loss-of-coolant-event (LOCA). In this study, the crack behavior of UO 2 pellets with controlled grain structure and Cr 2 O 3 doping was tested with rapid power ramping (300−900 °C per min) mimicking a prototypical LOCA heating profile. Dense micron-sized UO 2 pellets display well-maintained integrity without cracking with the ramping up to 1500 °C at a heating rate of 8 °C per second. Fracture occurs in both pure and Cr 2 O 3 -doped dense nano-sized UO 2 pellets. The Cr 2 O 3 doped oxide fuel pellet with a larger grain size (~ 22.2 μm) displays the best performance under LOCA testing due to its highest thermal conductivity under high temperature. FEA calculations suggest a temperature gradient across the fuel pellet during transient testing, resulting in residual stress and cracking, which can be correlated with their thermal-mechanical properties.

Zhao, Dong (ORCID:0000000191377257)↗

DOE OSTI2024

Elongate SiC fuel elements

An elongate fuel element is described that has a silicon carbide cladding enclosing a fuel, such as UO 2 , wherein the fuel is dimensioned relative to the cladding to define gaps at each lateral end of the enclosure sufficiently large such that upon swelling in use, the fuel does not increase the strain on the cladding beyond the limits of the claddings strain tolerance. The lateral gaps at the ends of the fuel allow lateral expansion during swelling that reduces the strain on the cladding.

Long, Yun-Bo↗

DOE OSTI2023

Grain boundary enhanced UN and U 3 Si 2 pellets with improved oxidation resistance

A method of forming a water resistant boundary on a fissile material for use in a water cooled nuclear reactor is described. The method comprises mixing a powdered fissile material selected from the group consisting of UN and U3Si2 with an additive selected from oxidation resistant materials having a melting or softening point lower than the sintering temperature of the fissile material, pressing the mixed fissile and additive materials into a pellet, sintering the pellet to a temperature greater than the melting point of the additive. Alternatively, if the melting point of the oxidation resistant particles is greater than the sintering temperature of UN or U3Si2, then the oxidation resistant particles can have a particle size distribution less than that of the UN or U3Si2.

Lahoda, Edward J.↗

DOE OSTI2022

Coated fuel pellets with enhanced water and steam oxidation resistance

Disclosed herein is a method comprising coating a fissile, uranium-containing ceramic material with a water-resistant layer, the layer being non-reactive with the fissile, uranium-containing ceramic material. The coating is applied to a surface of the fissile, uranium-containing ceramic material. Also disclosed is a fuel for use in a nuclear reactor.

Lahoda, Edward J.↗

DOE OSTI2022

Cold spray chromium coating for nuclear fuel rods

A zirconium alloy cladding tube for use in a water cooled nuclear reactor under normal operating conditions and under high temperature oxidation conditions is described. The cladding tube has a coating uniformly deposited thereon. The coating, which may be up to 300 microns thick, is selected from the group consisting of chromium, a chromium-based alloy, and combinations thereof.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Silicon carbide reinforced zirconium based cladding

A method for making an improved nuclear fuel cladding tube includes reinforcing a Zr alloy tube by first winding or braiding ceramic yarn directly around the tube to form a ceramic covering, then physically bonding the ceramic covering to the tube by applying a first coating selected from the group consisting of Nb, Nb alloy, Nb oxide, Cr, Cr oxide, Cr alloy, or combinations thereof, by one of a thermal deposition process or a physical deposition process to provide structural support member for the Zr tube, and optionally applying a second coating and optionally applying a third coating by one of a thermal deposition process or a physical deposition process. If the tube softens at 800° C.-1000° C., the structural support tube will reinforce the Zr alloy tube against ballooning and bursting, thereby preventing the release of fission products to the reactor coolant.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Control rods for light water reactors

A control rod for a nuclear fuel assembly is described herein that includes a neutron absorbing material having a melting point greater than 1500° C. that does not form a eutectic with a melting point less than 1500° C., and may further include a cladding material having a melting point greater than 1500° C. The cladding material is selected from the group consisting of silicon carbide, zirconium, a zirconium alloy, tungsten, and molybdenum. The absorbing material is selected from the group consisting of Gd2O3, Ir, B4C, Re, and Hf. The metal cladding or the absorbing material may be coated with an anti-oxidation coating of Cr with or without a Nb intermediate layer.

Lahoda, Edward J.↗

DOE OSTI2021

High-temperature oxidation and quenching of chromium-coated zirconium alloy ATF cladding tubes with and w/o pre-damage

Chromium-coated zirconium alloys are one of the promising candidates for accident-tolerant fuel cladding (ATF) tubes for light water reactors (LWRs). In this study, the high temperature oxidation and degradation of two types of Cr coatings (cold spray and physical vapor deposition) with and without pre-damage by scratches were investigated on prototype rod segment samples filled with ZrO 2 pellets and tightly sealed with welded end caps. Isothermal tests at 1100 and 1200 °C were terminated by quenching with water; transient tests were performed up to 1500–1600 °C until complete coating failure. The positive effect of both types of Cr coatings was observed in all tests. Pre-damaged specimens showed only locally increased oxidation of the scratched zone, but no negative effects on the adjacent Cr coating. Finally, the behavior of the two types of coatings is compared and the degradation mechanisms are discussed based on hydrogen release data, extensive metallographic post-test examinations, and the current state of global research.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Grain boundary enhanced UN and U3Si2 pellets with improved oxidation resistance

A method of forming a water resistant boundary on a fissile material for use in a water cooled nuclear reactor is described. The method comprises mixing a powdered fissile material selected from the group consisting of UN and U 3 Si 2 with an additive selected from oxidation resistant materials having a melting or softening point lower than the sintering temperature of the fissile material, pressing the mixed fissile and additive materials into a pellet, sintering the pellet to a temperature greater than the melting point of the additive. Alternatively, if the melting point of the oxidation resistant particles is greater than the sintering temperature of UN or U 3 Si 2 , then the oxidation resistant particles can have a particle size distribution less than that of the UN or U 3 Si 2 .

Lahoda, Edward J.↗

DOE OSTI2021

Uranium nitride (UN) pellets with controllable microstructure and phase – fabrication by spark plasma sintering and their thermal-mechanical and oxidation properties

Dense uranium mononitride (UN) pellets with controlled microstructures and tailored grain size from large-grained to a few microns are synthesized by spark plasma sintering (SPS) combined with high energy ball milling. The impacts of the sintering conditions on fuel microstructure, grain size, physical density, and phase behavior are systematically investigated, and the thermal-mechanical properties and oxidation behavior of the SPS densified UN pellets are characterized. Higher sintering temperatures and longer ball milling durations and thus finer starting UN powders promote sintering and densification, and dense UN pellets above 95% theoretical density can be achieved by SPS at 1873 K for 10 min. UN phase purity is maintained in the SPS-densified pellets sintered at a lower temperature and short duration. A phase heterogeneity with secondary UO 2 or uranium sesquinitride (U 2 N 3 ) occurs for the UN pellets sintered at higher temperatures using finer UN powders. The hardness and fracture toughness of the SPS-densified UN pellets increase with smaller grain sizes and higher densities to 7.9 GPa and 3.5 MPa m 1/2 , respectively. Furthermore, both small (1–2 μm) and large grain-sized (30–50 µm) UN pellets exhibit good thermal conductivity. Dynamic oxidation testing by a thermogravimetric analyzer in air shows that the onset temperature for oxidation varies with microstructure and phase heterogeneity of the SPS densified UN pellets. Particularly, the smaller-grained (micron-sized) UN pellets containing uranium oxides and U 2 N 3 display lower weight gain and significantly-reduced oxidation kinetics, and full oxidation completes at a temperature above 1173 K when tested with a ramp rate of 10 K/min.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Manufacture of large grain powders with granular coatings

The invention relates generally to uranium fuel in a nuclear reactor and, more particularly, the inclusion of a fuel additive component to the bulk fuel material. The fuel additive component is selected and provided in an amount such that it is effective to improve one or more properties of the bulk fuel material. The fuel additive component has a grain size that is less than the grain size of the bulk fuel material. The granular fuel additive component coats or covers the granular bulk fuel material.

Lahoda, Edward J.↗

DOE OSTI2021

Duplex accident tolerant coating for nuclear fuel rods

A method is described for forming duplex layers including an interlayer and a corrosion resistant boundary layer on a nuclear fuel rod cladding tube for use in a water cooled nuclear reactor. The method includes forming, by thermal deposition or physical vapor deposition, on the exterior of a substrate, an inner interlayer with Mo, Ta, W or Nb or other particles, and forming, by thermal deposition or physical vapor deposition, on the interlayer, an outer corrosion resistant layer with particles selected from the group consisting of Cr, a Cr alloy, and combinations thereof. The interlayer prevents eutectic formation between the corrosion resistant layer and the substrate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Method of manufacturing a reinforced nuclear fuel cladding using an intermediate thermal deposition layer

A method is described that includes the steps of making a thin walled Zr alloy tube, loading nuclear fuel pellets into the tube, compressing the tube onto the fuel pellets to substantially reduce free space around the fuel pellets, positioning end plugs at each of two ends of the tube, filling the tube with a heat transferring gas, and coating the compressed tube with a corrosion resistant material using a thermal deposition process, such as cold spray, before inserting the tube into a pre-formed SiC composite cover having at least one closed end.

Lahoda, Edward J.↗

DOE OSTI2021

Deposition of integrated protective material into zirconium cladding for nuclear reactors by high-velocity thermal application

A zirconium alloy nuclear reactor cylindrical cladding has an inner Zr substrate surface, an outer volume of protective material, and an integrated middle volume of zirconium oxide, zirconium and protective material, where the protective material is applied by impaction at a velocity greater than 340 meters/second to provide the integrated middle volume resulting in structural integrity for the cladding.

Mazzoccoli, Jason P.↗

DOE OSTI2021

Process for manufacturing SiC composite ceramics

A method is described for manufacturing a ceramic composite structure. The method includes wrapping ceramic fibers (22), such as SiC fibers, about the external surface of at least one form. The method further includes heating the wrapped fibers (22) to a temperature no greater than a first temperature, infiltrating voids (24) in the wrapped fibers (22) with the ceramic composite in a first vessel (12) at the first temperature, transferring the infiltrated wrapped fibers (22) from the first vessel (12) to a second vessel (14), distinct from the first vessel (12), and coating the infiltrated wrapped fibers (22) with the ceramic composite in the second vessel (14) at a second temperature, higher than the first temperature.

Lahoda, Edward J.↗

DOE OSTI2020

Coated U3Si2 pellets with enhanced water and steam oxidation resistance

A method of forming a water resistant boundary on a fissile material for use in a water cooled nuclear reactor is described. The method comprises coating the fissile material, such as a pellet of U3Si2 and/or the grain boundaries, to a desired thickness with a suitable coating material, such as atomic layer deposition or a thermal spray process. The coating material may be any non-reactive material with a solubility at least as low as that of UO2. Exemplary coating materials include ZrSiO4, FeCrAl, Cr, Zr, Al—Cr, CrAl, ZrO2, CeO2, TiO2, SiO2, UO2, ZrB2, Na2O—B2O3—SiO2—Al2O3 glass, Al2O3, Cr2O3, carbon, and SiC, and combinations thereof. The water resistant layer may be overlayed with a burnable absorber layer, such as ZrB2 or B2O3—SiO2 glass.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Cr-doped U 3 Si 2 composite fuels under steam corrosion

Dense Cr-doped U 3 Si 2 composite fuels were manufactured by spark plasma sintering, and the effects of Cr addition on mechanical properties and oxidation resistance were investigated. Furthermore, dynamic oxidation testing by thermogravimetric analysis revealed significantly improved oxidation resistance of U 3 Si 2 with minimal doping of 3 wt% Cr. The onset oxidation temperature increased to above 550 °C in air and ~520 °C in steam conditions for the 5 wt% and 10 wt% Cr-doped composites. Steam corrosion testing under 360 °C for 24 hours indicated well-maintained pellet integrity without pulverization for the 10 wt% Cr-doped U 3 Si 2 pellet which only showed minor surface oxidation. The first promising results open up the possibility of designing and manufacturing metal additive-doped U 3 Si 2 composite fuels with significantly-improved corrosion resistance as a potential candidate for accident tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Integration of real-time measurements and atomistic modeling to license nuclear components

An improved testing and data gathering method is described herein with reference to testing a new fuel, as an exemplary component to be tested for licensure purposes. The method includes generally: generating models for the new system; making samples and getting them accepted for a reactor; and testing the samples in a test or commercial reactor until the exposure time is reached for the expected cycle length of the fuel at final use. The method is preferably done concurrent to submitting a license application for commercial use of the new component to the relevant government body to expedite license testing review.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗