Engineering topics

Laible, Michael

Publications and source records attributed to Laible, Michael.

3 records

NASA NTRS2012

International Space Station Modal Correction Analysis

This paper summarizes the on-orbit modal test and the related modal analysis, model validation and correlation performed for the ISS Stage ULF4, DTF S4-1A, October 11,2010, GMT 284/06:13:00.00. The objective of this analysis is to validate and correlate analytical models with the intent to verify the ISS critical interface dynamic loads and improve fatigue life prediction. For the ISS configurations under consideration, on-orbit dynamic responses were collected with Russian vehicles attached and without the Orbiter attached to the ISS. ISS instrumentation systems that were used to collect the dynamic responses during the DTF S4-1A included the Internal Wireless Instrumentation System (IWIS), External Wireless Instrumentation System (EWIS), Structural Dynamic Measurement System (SDMS), Space Acceleration Measurement System (SAMS), Inertial Measurement Unit (IMU) and ISS External Cameras. Experimental modal analyses were performed on the measured data to extract modal parameters including frequency, damping and mode shape information. Correlation and comparisons between test and analytical modal parameters were performed to assess the accuracy of models for the ISS configuration under consideration. Based on the frequency comparisons, the accuracy of the mathematical models is assessed and model refinement recommendations are given. Section 2.0 of this report presents the math model used in the analysis. This section also describes the ISS configuration under consideration and summarizes the associated primary modes of interest along with the fundamental appendage modes. Section 3.0 discusses the details of the ISS Stage ULF4 DTF S4-1A test. Section 4.0 discusses the on-orbit instrumentation systems that were used in the collection of the data analyzed in this paper. The modal analysis approach and results used in the analysis of the collected data are summarized in Section 5.0. The model correlation and validation effort is reported in Section 6.0. Conclusions and recommendations drawn from this analysis are included in Section 7.0.

Fotz[atrocl. Lrostom↗

NASA NTRS2012

International Space Station 2A Array Modal Analysis

On December 9th 2009, the International Space Station (ISS) 2A solar array mast experienced prolonged longeron shadowing during a Soyuz undocking. Analytical reconstruction of induced thermal and dynamic structural loads showed an exceedance of the mast buckling limit. Possible structural damage to the solar array mast could have occurred during this event. A Low fidelity video survey of the 2A mast showed no obvious damage of the mast longerons or battens. The decision was made to conduct an on-orbit dynamic test of the 2A array on December 18th, 2009. The test included thruster pluming on the array while photogrammetry data was recorded. The test was similar to other Dedicated Thruster Firings (DTFs) that were performed to measure structural frequency and damping of a solar array. Results of the DTF indicated lower frequency mast modes than model predictions, thus leading to speculation of mast damage. A detailed nonlinear analysis was performed on the 2A array model to assess possible solutions to modal differences. The setup of the parametric nonlinear trade study included the use of a detailed array model and the reduced mass and stiffness matrices of the entire ISS being applied to the array interface. The study revealed that the array attachment structure is nonlinear and thus was the source of error in the model prediction of mast modes. In addition, a detailed study was performed to determine mast mode sensitivity to mast longeron damage. This sensitivity study was performed to assess if the ISS program has sufficient instrumentation for mast damage detection.

Laible, Michael↗

NASA NTRS2003

International Space Station Microgravity Analytical Model Correlation And Update

The acceleration environment aboard the completed International Space Station (ISS) is a key resource for scientific and technological endeavors. Hardware verification activIties and early measurements indicate that the ISS is well on the way of meeting these "Assembly Complete" "microgravity" provisions, however, the simulation models that compute these accelerations have, to date, lacked the high degree of empirical validation typical of standard aerospace industry practices. Assembly stage, on-orbit measurements are used to address this shortcoming and to develop higher confidence in the simulation models. The Phase I correlation results show the analyses to be consistently conservative, producing higher than measured levels. The 25 to 30% greater quasi-steady computations are deemed acceptable for verification. Updates are made to localized structural dynamic and vibroacoustic parameters that reduce responses in selected one-third octave bands by almost 50%. These models are then used for the Assembly Complete verification analysis which concludes that the ISS vehicle meets the ISS microgravity requirements with minor reservations. Two of the sixteen rack are marginally non-compliant in the quasi-steady regime, and operational constraints are needed on the U. S. Lab and ESA APM vacuum resource vents, and the Russian Resistive Exercise Device in the structural dynamic regime.

DelBasso, Steve↗