Blade loading and rotation effects on compressor rotor wake near end walls
(Previously cited in issue 08, p. 1179, Accession no. A82-22063)
Lakshminarayana, B.↗
Engineering topics
Lakshminarayana, B.
Publications and source records attributed to Lakshminarayana, B..
Wall boundary layer development near the tip region of an IGV of an axial flow compressor
The annulus wall boundary layer inside the blade passage of the inlet guide vane (IGV) passage of a low-speed axial compressor stage was measured with a miniature five-hole probe. The three-dimensional velocity and pressure fields were measured at various axial and tangential locations. Limiting streamline angles and static pressures were also measured on the casing of the IGV passage. Strong secondary vorticity was developed. The data were analyzed and correlated with the existing velocity profile correlations. The end wall losses were also derived from these data.
Lakshminarayana, B.↗
End wall flow characteristics and overall performance of an axial flow compressor stage
This review indicates the possible future directions for research on endwall flows in axial flow compressors. Theoretical investigations on the rotor blade endwall flows in axial flow compressors reported here include the secondary flow calculation and the development of the momentum integral equations for the prediction of the annulus wall boundary layer. The equations for secondary vorticity at the rotor exit are solved analytically. The solution includes the effects of rotation and the viscosity. The momentum integral equations derived include the effect of the blade boundary layers. The axial flow compressor facility of the Department of Aerospace Engineering at The Pennsylvania State University, which is used for the experimental investigations of the endwall flows, is described in some detail. The overall performance and other preliminary experimental results are presented. Extensive radial flow surveys are carried out at the design and various off design conditions. These are presented and interpreted in this report. The following experimental investigations of the blade endwall flows are carried out. (1) Rotor blade endwall flows: The following measurements are carried out at four flow coefficients. (a) The rotor blade static pressures at various axial and radial stations (with special emphasis near the blade tips). (b) The hub wall static pressures inside the rotor blade passage at various axial and tangential stations. (2) IGV endwall flows: The following measurements are carried out at the design flow coefficient. (a) The boundary layer profiles at various axial and tangential stations inside the blade passage and at the blade exit. (b) Casing static pressures and limiting streamline angles inside the blade passage.
Sitaram, N.↗
End wall flows in rotors and stators of a single stage compressor
A computer code for solving the parabolized Navier-Stokes equations for internal flows was developed. Oscillations that develop in the calculation procedure are discussed. The measurements made in the hub and annulus wall boundary layers are summarized. The flow in the hub wall boundary layer, starting ahead of the inlet guide vanes to the inlet of the rotor is traced.
Govindan, T. R.↗
Three dimensional flow field inside compressor rotor, including blade boundary layers
The space marching code was modified in order to be able to predict the flow field inside a rotor passage, including the blade and hub wall boundary layers. The basic changes incorporated are modifications of the equations so that the code can handle three dimensional configurations with changes in the radial direction (for example changes in stagger angle, blade camber and thickness), extensions and modifications in order to implement a physically realistic turbulence model such as a k sigma model and an algebraic Reynolds stress model.
Pouagare, M.↗
A turbulence model for three dimensional turbulent shear flows over curved rotating bodies
There exists currently considerable interest in the development of numerical procedures for solving the equations governing three-dimensional fluid flows. In particular, improved calculations of viscous flows on rotating bodies such a turbomachinery rotors are of great importance. The present investigation is mainly concerned with the analysis of the effect of rotation on the dissipation rate equation and the Reynolds stress equations. Attention is given to governing equations and modelling, algebraic Reynolds stress equations, a procedure for implementing the turbulence closure scheme, results for a model representative of centrifugal turbomachinery, and results for axial turbomachinery. The proposed turbulence model is valid for three-dimensional, rotating, and curved flows. The model has all the essential physics of turbulence, mean flow, rotation, and the curvature.
Galmes, J. M.↗
Investigation of the tip clearance flow inside and at the exit of a compressor rotor passage. II - Turbulence properties
The flow in the tip clearance region of a compressor rotor is highly turbulent due to the strong interaction of the leakage flow with the annulus wall boundary layer. This paper deals with the turbulence properties of the flow in the tip clearance region of a moderately loaded compressor rotor. The experimental results reported in this paper were obtained using a two-sensor hot-wire probe in combination with an ensemble averaging technique. Blade-to-blade distribution of the axial and tangential turbulence intensities at various radial locations and ten axial locations (four inside the blade passage and the remaining six outside the passage) were derived from this data. Isointensity contours in the clearance region at various radial locations were also obtained from the experimental data. A region of very high turbulence intensities was indicated at the half-chord location from these results. The turbulence intensity profiles also indicated that the leakage flow travels toward the midpassage before rolling up. The turbulence is almost isotropic beyond three-quarter chord downstream of the trailing edge.
Pandya, A.↗
Tip clearance flow in a compressor rotor passage at design and off-design conditions
The flow field in the tip clearance region of a compressor rotor at an off-design condition is reported in this paper. The earlier data at the design condition has also been re-interpreted and correlated with the blade and the flow parameters. The measurements inside the rotor tip region are acquired using a miniature hot wire sensor of 'V' configuration. The instantaneous velocity data is analyzed by the ensemble averaging technique to derive the blade-to-blade velocity field at various axial and radial locations between the rotor tip and the casing. The flow and the blade pressure data at the design condition are compared with the data at the off-design condition (lower blade loading). In addition to a reduction in the leakage velocities, its chordwise variation is also altered substantially at the lower blade loading.
Lakshminarayana, B.↗
Computation of viscous flows in turbomachinery cascades
Analytic and numerical experiments involving the use of the space-marching method for the prediction of the viscous flow field in turbomachinery cascades indicate that the grid lines in the physical domain must be nearly orthogonal in order to arrive at accurate predictions. For staggered cascades, a nonperiodic grid system was used and appropriate approximations were applied in place of the periodicity boundary conditions upstream and downstream of the cascade. Predicted drag coefficient, turning angle, boundary layer momentum thicknesses, and velocity profiles are compared with experimental data. Good agreement is obtained in most cases.
Pouagare, M.↗
Fluid dynamics of inducers - A review
The objective of this paper is to review the experimental and analytical investigations on the fluid dynamic aspects of noncavitating inducers. Various analyses available for the prediction of the flow field, starting from the simple radial equilibrium analysis to the numerical solution of exact three-dimensional inviscid and viscid flow equations, are reviewed. The experimental data on the overall inducer performance, rotor blade passage measurements, and boundary layer on rotor blades are critically examined. Some of the available data have been reinterpreted to provide suitable guidance to the designer. The review and the concluding remarks include a global view of the state-of-the-art and applicability of the research to design, and some viewpoints on the analysis and design of inducers.
Lakshminarayana, B.↗
Development of secondary flow and vorticity in curved ducts, cascades, and rotors, including effects of viscosity and rotation
This paper is concerned with the numerical solution of the secondary vorticity equations in curved ducts, cascades, and rotors. The classical approach of splitting the flow into primary and secondary flow fields is employed and extended to include effects of viscosity, rotation, and density stratification. All elliptical effects are neglected and the Crank-Nicolson method is used to solve the secondary vorticity equation. The secondary flow field is obtained by solving a Poisson equation using a successive over-relaxation method. The results are compared with theoretical and experimental data from stationary ducts, compressor and turbine cascades. The agreement is good for most of the cases.
Pouagare, M.↗
Three dimensional flow field inside compressor rotor, including blade boundary layers
The Reynolds stress equation, pressure strain correlation, and dissipative terms and diffusion are discussed in relation to turbulence modelling using the Reynolds stress model. Algebraic modeling of Reynolds stresses and calculation of the boundary layer over an axial cylinder are examined with regards to the kinetic energy model for turbulence modelling. The numerical analysis of blade and hub wall boundary layers, and an experimental study of rotor blade boundary layer in an axial flow compressor rotor are discussed. The Patankar-Spalding numerical method for two dimensional boundary layers is included.
Galmes, J. M.↗
Three dimensional flow field inside the passage of a low speed axial flow compressor rotor
Measurements of the subsonic flow in the rotor passage of a single stage axial flow compressor were made to study the nature of the flow field and to verify the existing numerical codes. The velocity and pressure fields were measured across the entire rotor passage at six axial locations and at five radial locations. A five-hole probe, rotating with the rotor, was used to measure the three components of velocity, the static and the total pressure. The experimental results are compared with the predictions from Katsanis and McNally's computer program. The agreement between the two is good for most of the cases.
Pouagare, M.↗
Three dimensional turbulent boundary layer development on a fan rotor blade
This paper is concerned with an experimental study undertaken to measure the boundary layer growth on a fan rotor blade. The measurements were carried out using a miniature 'X' configuration hot wire probe at various chordwise and radial locations on both surfaces of the blade. The streamwise and radial velocity profiles as well as the corresponding intensity components are interpreted and correlated. The validity of conventional velocity profiles such as the 'law of the wall' for the streamwise profile and the hodograph plot for the cross flow profile are examined. The measured values of boundary-layer gross properties are compared with the predictions based on a momentum-integral technique.
Lakshminarayana, B.↗
Three dimensional mean velocity and turbulence characteristics in the annulus wall region of an axial flow compressor rotor passage
The experiment was performed using the rotating hot-wire technique within the rotor blade passage and the stationary hot-wire technique for the exitflow of the rotor blade passage. The measurements reveal the effect of rotation and subsequent flow interactions upon the rotor blade flowfield and wake development in the annulus-wall region. The flow near the rotor blade tips is found to be highly complex due to the interaction of the annulus-wall boundary layer, the blade boundary layers, the tip leakage flow, and the secondary flow. Within the blade passage, this interaction results in an appreciable radial inward flow as well as a defect in the mainstream velocity near the mid-passage. Turbulence levels within this region are very high. This indicates a considerable extent of flow mixing due to the viscous flow interactions. The size and strength of this loss core is found to grow with axial distance from the blade trailing edge. The nature of the rotor blade exit-flow was dominated by the wake development.
Davino, R.↗
Investigation of the tip clearance flow inside and at the exit of a compressor rotor passage
The nature of the tip clearance flow in a moderately loaded compressor rotor is studied. The measurements were taken inside the clearance between the annulus-wall casing and the rotor blade tip. These measurements were obtained using a stationary two-sensor hot-wire probe in combination with an ensemble averaging technique. The flowfield was surveyed at various radial locations and at ten axial locations, four of which were inside the blade passage in the clearance region and the remaining six outside the passage. Variations of the mean flow properties in the tangential and the radial directions at various axial locations were derived from the data. Variation of the leakage velocity at different axial stations and the annulus-wall boundary layer profiles from passage-averaged mean velocities were also estimated.
Pandya, A.↗
Three-dimensional flow field in the tip region of a compressor rotor passage. I - Mean velocity profiles and annulus wall boundary layer
A rotating three-sensor, hot-wire probe has been used along with rotor blade static pressure measurements to investigate the complex inviscid and viscid effects in the annulus wall flowfield, including the three components of mean velocity, turbulence intensity, and turbulence stress inside the rotor blade passage. It is found that the tip leakage flow originates near quarter-chord, with peak values occurring near mid-chord. The leakage flow, which is in the form of a jet within the blade row, is augmented by the blade rotation and travels further away from the suction surface than that observed in stationary blade rows and cascades. This leakage flow tends to roll up between the mid-passage and the pressure surface near the tip region; the vortex formation does not occur within the passage in this particular case.
Lakshminarayana, B.↗
Investigation of the tip-clearance flow inside and at the exit of a compressor rotor passage. I - Mean velocity field
A stationary two-sensor hot-wire probe has been used in combination with an ensemble averaging technique to measure the flow in the tip clearance region of a compressor rotor with emphasis on the leakage flow development inside the tip-clearance region and at the exit of the rotor. It is found that the presence and interaction of leakage flow, annulus boundary layer, and the scraping vortex is the dominant feature at mid-chord position. The rotation of the blade augments the leakage flow, resulting in the movement of the leakage jet toward the mid-passage. The blade-to-blade distribution of properties is shown to be highly nonuniform, except in the downstream and upstream regions.
Pandya, A.↗