Search NASA⌕ Search

Engineering topics

Lamb, M.

Publications and source records attributed to Lamb, M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Integration effects of underwing forward- and rearward-mounted separate-flow, flow-through nacelles on a high-wing transport

An experimental investigation was conducted in the Langley 16-Foot Transonic Tunnel at free-stream Mach numbers from 0.70 to 0.82 and angles of attack from -2.5 to 4.0 degrees to determine the integration effects of pylon-mounted underwing forward and rearward separate-flow, flow-through nacelles on a high-wing transonic transport configuration. The results showed that the installed drag of the nacelle/pylon in the rearward location was slightly less than that of the nacelle/pylon in the forward location. This reduction was due to the reduction in calculated skin friction of the nacelle/pylon configuration. In all cases the combined value of form, wave, and interference drag was excessively high. However, the configuration with the nacelle/pylon in a rearward location produced an increase in lift over that of the basic wing-body configuration.

Lamb, M.↗
NASA NTRS1985

Nacelle/pylon/wing integration on a transport model with a natural laminar flow nacelle

Tests were conducted in the Langley 16-Foot Transonic Tunnel at free-stream Mach numbers from 0.70 to 0.82 and angles of attack from -2.5 deg to 4.0 deg to determine if nacelle/pylon/wing integration affects the achievement of natural laminar flow on a long-duct flow-through nacelle for a high-wing transonic transport configuration. In order to fully assess the integration effect on a nacelle designed to achieve laminar flow, the effects of fixed and free nacelle transitions as well as nacelle longitudinal position and pylon contouring were obtained. The results indicate that the ability to achieve laminar flow on the nacelle is not significantly altered by nacelle/pylon/wing integration. The increment in installed drag between free and fixed transition for the nacelles on symmetrical pylons is essentially the calculated differences between turbulent and laminar flow on the nacelles. The installed drag of the contoured pylon is less than that of the symmetrical pylon. The installed drag for the nacelles in a rearward position is greater than that for the nacelles in a forward position.

Lamb, M.↗
NASA NTRS1983

Body-surface pressure data on two monoplane-wing missile configurations with elliptical cross sections at Mach 2.50

Tabulated body surface pressure data for two monoplane-wing missile configurations are presented and analyzed. Body pressure data are presented for body-alone, body-tail, and body-wing-tail combinations. For the lost combination, data are presented for tail-fin deflection angles of 0 deg and 30 deg to simulate pitch, yaw, and roll control for both configurations. The data cover angles of attack from -5 deg to 25 deg and angles of roll from 0 deg to 90 deg at a Mach number of 2.50 and a Reynolds number of 6.56 x 1,000,000 per meter. Very consistent, systematic trends with angle of attack and angle of roll were observed in the data, and very good symmetry was found at a roll angle of 0 deg. Body pressures depended strongly on the local body cross-section shape, with very little dependence on the upstream shape. Undeflected fins had only a small influence on the pressures on the aft end of the body; however, tail-fin deflections caused large changes in the pressures.

Allen, J. M.↗
NASA NTRS1981

Stability and control characteristics of a monoplanar missile configuration with triform-tail-fin arrangements at Mach numbers from 1.70 to 2.86

A wind-tunnel missile model with either a lower vertical tail fin with a pair of horizontal fins having 0 deg, 22.5 deg, or 30 deg dihedral or an upper vertical tail fin with horizontal fins having 0 deg, -22.5 deg, or -30 deg dihedral was investigated. The results indicated that those configurations with horizontal fins at or below the horizontal plane had nearly linear pitching-moment characteristics, while those with the horizontal fins above the horizontal plane experienced pitch-up which increased with increasing horizontal-fin-dihedral angle. At zero angle of attack, the configurations were directionally stable at most test Mach numbers. Generally, those configurations with the upper vertical fin had positive effective dihedral at zero angle of attack, while those with he lower vertical fin had negative effective dihedral. For roll control, three deflected tail fins produced more total roll control than two horizontal fins. For yaw control, three tail fins deflected equally or differentially produced more total yaw control than the single vertical fin.

Lamb, M.↗
NASA NTRS1981

Experimental and theoretical supersonic lateral-directional stability characteristics of a simplified wing-body configuration with a series of vertical-tail arrangements

An experimental investigation was conducted to provide a systematic set of lateral-directional stability data for a simplified wing-body model with a series of vertical-tail arrangements. The study was made at Mach numbers from 1.60 to 2.86 at nominal angles of attack from -8 to 12 deg and Reynolds number of 8.2 million per meter. Comparisons at zero angle of attack were made with three existing theoretical methods (MISLIFT - a second-order shock expansion and panel method; APAS - a slender body and first order panel method; and PAN AIR - a higher order panel method) and comparisons at angle of attack were made with PAN AIR. The results show that PAN AIR generally provides accurate estimates of these characteristics at moderate angles of attack for complete configurations with either single or twin vertical tails. APAS provides estimates for complete configurations at zero angle of attack. However, MISLIFT only provides estimates for the simplest body-vertical-tail configurations at zero angle of attack.

Lamb, M.↗
NASA NTRS1981

Wing-alone aerodynamic characteristics for high angles of attack of supersonic speeds

An experiment was conducted to determine wing-alone supersonic aerodynamic characteristics at high angles of attack. The wings tested varied in aspect ratio from 0.5 to 4.0 and in taper ratio from 0 to 1.0. The wings were tested at angles of attack ranging rom -5 deg to 60 deg and at Mach number from 1.60 to 4.60. The aerodynamic characteristics were obtained by integrating local pressures measured over the wing surfaces. Presented and discussed are results showing the effects of aspect ratio, taper ratio, Mach number, and angle of attack on force and moment coefficients and center of pressure locations. Also included are tabulations of the pressure measurements.

Stallings, R. L., Jr.↗
NASA NTRS1981

Theoretical and experimental supersonic lateral-directional stability characteristics

A program has been initiated at NASA Langley Research Center to assess several methods for estimation of lateral-directional stability. As a basis for comparison, experimental data are presented for a simple wing-body vertical tail configuration. The methods for estimating the characteristics include a second-order shock expansion and panel method (MISLIFT), a slender body and 'first-order' panel method (APAS), and a 'higher-order' panel method for linearized supersonic flow (PAN AIR). The results show that PAN AIR provides accurate estimates of these characteristics at moderate angles of attack for complete configurations with either single or twin vertical tails. APAS provides estimates for complete configurations at zero angle of attack. However, MISLIFT only provides estimates for the simplest body-vertical tail configurations at zero angle of attack.

Lamb, M.↗
NASA NTRS1981

Wing-alone aerodynamic characteristics at high angles of attack

An experimental investigation has been conducted to determine wing-alone supersonic aerodynamic characteristics at high angles of attack. The family of wings tested varied in aspect ratio from 0.5 to 4.0 and taper ratio from 0.0 to 1.0. The wings were tested at angles of attack ranging from 0 to 60 deg and Mach numbers from 1.6 to 4.6. The aerodynamic characteristics were obtained by integrating local pressures measured over the wing surface. Comparison of these data with the limited available data from the literature indicate the present data are free of sting interference effects through the test range of angle of attack. Presented and discussed are results showing the effects of model geometry, Mach number and angle of attack on aerodynamic characteristics consisting of normal force, pitching moment, bending moment, longitudinal center-of-pressure locations, and lateral center-of-pressure locations.

Stallings, R. L., Jr.↗
NASA NTRS1980

Wind-tunnel measurements and comparison with flight of the boundary layer and heat transfer on a hollow cylinder at Mach 3

The wind tunnel tests were conducted both with and without boundary layer trips at Mach 3 and nominal free stream Reynolds numbers per meter ranging from 3.3 x 10 the 6th power. Instrumentation consisted of pressure orifices, thermocouples, a boundary layer pitot pressure rake, and a floating element skin friction balance. Measurements from both wind tunnel and flight were compared with existing engineering prediction methods.

Stallings, R. L., Jr.↗
NASA NTRS1980

Effect of Reynolds number on stability characteristics of a cruciform wing-body

An experimental investigation was conducted to determine the effect of Reynolds number on the stability characteristics of a body with cruciform wings at large angles of attack. Pressure distributions and force and moment data (axial force not measured) are presented for Mach 1.60 and 2.70, Reynolds numbers based on body diameter from approximately 130,000 to 2,800,000, and angles of attack from 0 deg to 50 deg. In general, the data show only small effects of Reynolds number throughout the range of test condition. Also discussed are force balance and pressure data that suggest a direct relationship between wind choking and the onset of a nonlinear stability variaton with angle of attack.

Stallings, R. L., Jr.↗
NASA NTRS1980

A Study of Panel Loads and Centers of Pressure of Three Different Cruciform Aft-Tail Control Surfaces of a Wingless Missile from Mach 1.60 to 3.70

An investigation was made of the forces and moments on the cruciform aft-tail control surfaces of a wingless missile model to determine the variation of panel load and center of pressure with angle of attack, tail deflection, model roll angle, and Mach number. Also, a limited force-moment and surface-pressure investigation was made on a noncircular aft end. These investigations were made in a unitary plan wind tunnel at Mach numbers of 1.60, 2.36, and 3.70 and at a Reynolds number per meter of 6,600,000. The cruciform aft-tail results indicate very little variation in the center of pressure for the highly loaded windward tail. The noncircular aft-end test results indicate no significant effect of the fin unporting on the fin loads.

Lamb, M.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at mach 1.60, 2.36, and 3.70 Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in the Langley Unitary Plan wind tunnel are presented. The data were obtained for three sets of cruciform aft-tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 degrees to 20 degrees, model roll angles from 0 degrees to 90 degrees, and tail deflections of 0 degrees and 15 degrees. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-control surfaces of a wingless missile at Mach 1.60, 2.36, and 3.70. Volume 2: Clipped delta tail

Pressure coefficients were obtained in the Langley Unitary Plan wind tunnel for a wingless missile with a clipped delta tail. The angle of attack was varied from -4 deg to 20 deg, model roll angle was varied from 0 deg to 90 deg in 22.5 deg increments, and tail deflections were 0 deg to - 15 deg. The pressures were measured on two adjacent tail surfaces using 91 pressure orifices per tail surface. Results are presented in plotted and tabular form.

Lamb, M.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at Mach 1.60, 2.36, and 3.70. Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in a wind tunnel are presented without analysis. The data were obtained for trapezoidal aft tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 to 20 deg model roll angles from 0 to 90 deg and tail deflections of 0 and -15 deg. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗
NASA NTRS1979

Aerodynamic characteristics at Mach numbers of 1.5, 1.8, and 2.0 of a blended wing-body configuration with and without integral canards

An exploratory, experimental, and theoretical investigation was made of a cambered, twisted, and blended wing-body concept with and without integral canard surfaces. Theoretical calculations of the static longitudinal and lateral aerodynamic characteristics of the wing-body configurations were compared with the characteristics obtained from tests of a model in the Langley Unitary Plan wind tunnel. Mach numbers of 1.5, 1.8, and 2.0 and a Reynolds number per meter of 6.56 million were used in the calculations and tests. Overall results suggest that planform selection is extremely important and that the supplemental application of new calculation techniques should provide a process for the design of supersonic wings in which spanwise distribution of upwash and leading-edge thrust might be rationally controlled and exploited.

Robins, A. W.↗
NASA NTRS1977

Effects of roughness size on the position of boundary-layer transition and on the aerodynamic characteristics of a 55 deg. swept delta wing at supersonic speeds

An experimental investigation was conducted to determine the effects of roughness size on the position of boundary layer transition and on the aerodynamic characteristics of a 55 deg swept delta wing model. Results are presented and discussed for wind tunnel tests conducted at free stream Mach numbers from 1.50 to 4.63, Reynolds numbers per meter from 3,300,000 to 1.6 x 10 to the 7th power, angles of attack from -8 to 16 deg, and roughness sizes ranging from 0.027 cm sand grit to 0.127 cm high cylinders. Comparisons were made with existing flat plate data. An approximate method was derived for predicting the drag of roughness elements used in boundary layer trips.

Stallings, R. L., Jr.↗