Search NASA⌕ Search

Engineering topics

Landel, R. F.

Publications and source records attributed to Landel, R. F..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Nonlinear mechanical behavior of thermoplastic matrix materials for advanced composites

Two recent theories of nonlinear mechanical response are quantitatively compared and related to experimental data. Computer techniques are formulated to handle the numerical integration and iterative procedures needed to solve the associated sets of coupled nonlinear differential equations. Problems encountered during these formulations are discussed and some open questions described. Bearing in mind these cautions, the consequences of changing parameters that appear in the formulations on the resulting engineering properties are discussed. Hence, engineering approaches to the analysis of thermoplastic matrix material can be suggested.

Arenz, R. J.↗
NASA NTRS1988

On the viscoplastic response of a composite wafer

In the present treatment of a viscoplastic composite wafer formed from a viscoplastic matrix that is reinforced by elastic or viscoplastic fibers attached to its plane surfaces, one constitutive equation is established by considering the viscoplastic behavior of the matrix as determined by an integral-type constitutive law whose intrinsic time-measure is pertinent to endochronic viscoplasticity. Attention is given to asymptotic cases where fiber stiffnesses and the hydrostatic modulus of the wafer are much larger than the latter's shear modulus. An explicit calculation is used when the stress field is uniaxial.

Valanis, K. C.↗
NASA NTRS1987

Cell model and elastic moduli of disordered solids - Low temperature limit

The cell theory has been previously employed to compute the equation of state of a disordered condensed system. It is now generalized to include anisotropic stresses. The condition of affine deformation is adopted, transforming an orginally spherical into an ellipsoidal cell. With a Lennard-Jones n-m potential between nonbonded centers, the formal expression for the deformational free energy is derived. It is to be evaluated in the limit of the linear elastic range. Since the bulk modulus in this limit is already known, it is convenient to consider a uniaxial deformation. To begin with, restrictions are made to the low-temperature limit in the absence of entropy contributions. Young's modulus and Poisson's ratio then follow.

Peng, S. T. J.↗
NASA NTRS1984

Free Volume Considerations in Thermoplastic and Thermosetting Resins

The direct measurement of physical aging and of the volume changes which go on during the course of this aging is discussed. Data on PMMA showing its physical aging as measured by its stress relaxation response and the accompanying volume changes are presented. An indication of how one can measure the free volume both directly from the volume change itself and relatively directly via a new technique is given. The application of this new technique (electron spin resonance spectroscopy) to other polymer systems is demonstrated.

Landel, R. F.↗
NASA NTRS1983

Influence of the microstructure on the corrosion behavior of magnetron sputter-quenched amorphous metallic alloys

The microstructure and corrosion behavior of magnetron sputter deposited amorphous metallic films of (Mo6ORu40)82B18 under varying sputtering atmospheres have been investigated. The microstructural details and topology of the films have been studied by scanning electron microscopy and correlated with the deposition conditions. By reducing the pressure of pure argon gas, the characteristic features of rough surface and columnar growth full of vertical voids can be converted into a mirror-smooth finish with very dense deposits. Films deposited in the presence of O2 or N2 exhibit columnar structure with vertical voids. Film deposited in pure argon at low pressure show remarkably high corrosion resistance due to the formation of a uniform passive surface layer. The influence of the microstructure and surface texture on the corrosion behavior is discussed.

Thakoor, A. P.↗
NASA NTRS1983

Rheological behavior of FM-9 solutions and correlation with flammability test results and interpretations

The rheological behavior of progressively shear thickening FM-9 solutions, a time-dependent shear thickening material with characteristics of threshold behavior, is investigated as part of a study of the rheological properties of antimisting jet fuel. Flammability test results and test configurations from various sources are evaluated. A correlation is obtained between the rheological behavior and the flammability tests such that, for a given system, such as a fixed solvent system and the FM-9 polymer system, the flammability criterion can be applied to a wide range of concentrations and temperatures.

Peng, S. T. J.↗
NASA NTRS1982

Deformation-Induced Anisotropy of Polymers

New theory calculates anisotropies induced by large deformations in polymers. Theory was developed primarily for calculating anistropy of thermal expansivity, but is also applicable to thermal conductivity, elastic moduli and other properties. Theory assumes that in isotropic state, long polymer chains are randomly coiled and not oriented in particular direction. They acquire an orientation when material is deformed. As average molecular orientation increases with deformation, properties of bulk material exhibit averaging of the microscopic anistropies of the oriented molecular segments.

Peng, S. T. J.↗
NASA NTRS1981

Rheological behavior of progressively shear-thickening solutions

The rheological behavior of the recently developed polymer FM-9 in Jet A fuel and JP 8 fuel is reported. In aqueous solution, FM 9 is found to exhibit strong time-dependent shear thickening behavior. Induction time necessary for the onset of thickening is found to depend on shear rate, solvent, concentration, and molecular weight. Altering the nature of the solvent results in effects similar to those obtained by changing the concentration or molecular weight. A critical shear rate is derived, and is inversely proportional to the zero shear rate viscosity of the solution for the temperature and concentrations observed. The onset of shear thickening behavior appears to be related to the onset of viscoelastic response, and thus the time scale follows reduced variable behavior.

Peng, S. T. J.↗
NASA NTRS1981

Analysis of the tensile stress-strain behavior of elastomers at constant strain rates. I - Criteria for separability of the time and strain effects

A theoretical analysis of the tensile stress-strain relation of elastomers at constant strain rate is presented which shows that the time and the stress effect are separable if the experimental time scale coincides with a segment of the relaxation modulus that can be described by a single power law. It is also shown that time-strain separability is valid if the strain function is linearly proportional to the Cauchy strain, and that when time-strain separability holds, two strain-dependent quantities can be obtained experimentally. In the case where time and strain effect are not separable, superposition can be achieved only by using temperature and strain-dependent shift factors.

Hong, S. D.↗
NASA NTRS1981

Problems encountered with conventional fiber-reinforced composites

Preparational, computational, and operational problems associated with fiber-reinforced composites (FRC) are reviewed. Initial preparation of FRCs is shown to involve consideration of the type of prepreg, the setting time, cure conditions and cycles, and cure temperatures. The effects of the choice of bonding agents, the fiber transfer length, and individual fiber responses to bonding agents are noted to have an impact on fiber strength, moisture uptake, and fatigue resistance. The deformation prior to failure and the failure region are modeled through models of mini-, micro- and macro mechanics formulations employing a stiffness matrix, failure criterion, or fracture mechanics. The detection, evaluation, and repair of defects comprises the operational domain, and it is stressed that no good repair techniques exist for FRCs.

Landel, R. F.↗
NASA NTRS1980

An equation of state for liquids

Closed expression for volume as function of pressure and temperature has been verified for over 250 liquids. Equation can assist chemical engineers, soild-state researchers, and others with interest in thermodynamic behavior of liquids.

Fedors, R. F.↗
NASA NTRS1980

Influence of antimisting polymer on aviation fuel breakup

Experiments have been performed to determine the influence of a moving airstream on jet and drop breakup of fuel containing small concentrations of antimisting polymers. This study was motivated by the needs to inhibit the ignition of fuel during a survivable aircraft crash landing. High speed motion pictures of initial deformation rates and instant pictures of initial deformation rates and instant pictures of the drop breakup suggest that the enormous resistance to the sudden deformation of fuel containing antimisting polymer is related to the development of high tensile viscosity, even though the shear viscosity is not markedly affected. Study of a pendant drop fiber was undertaken to determine this tensile viscosity of antimisting fuel as a function of temperature and of polymer concentration.

Sarohia, V.↗
NASA NTRS1980

Extensional flow of dilute polymer solution

Simultaneous effects of temperature and concentration on tensile viscosity are investigated using a semi-empirical scaling law established to relate the concentration, temperature and deformation rate by a reduced deformation rate variable. Results show the onset of high viscosity occurring in the vicinity of the onset of non-Newtonian viscosity observed in a simple shear flow experiment. High viscosity is also compared with steady and dynamic shear data. Finally, the asymptotic solution of Hassager's kinetic theory of a bead-rod model for macromolecular solutions is compared with the data, indicating that tensile viscosity depends strongly on the molecular weight, the higher the molecular weight, the more sensitive the tensile viscosity in terms of the deformation rate.

Peng, S. T. J.↗
NASA NTRS1977

Reduced variable technique for predicting grain behavior

The use of reduced variables to account for the time-temperature dependence of the relaxation modulus is a standard and universally adopted technique in the stress analysis of solid propellant grains. Recent work has suggested that the reduced variable technique can also be used to account for the dependence of the relaxation modulus on the crosslink density of an elastomer system. By combining variables, it is now possible to determine the relaxation modulus as a function of both mechanical and chemical parameters over a long period of time. The problems involved, the pitfalls to be avoided, and suggested techniques to be used in acquiring data are discussed.

Lewis, G. W.↗
NASA NTRS1977

Nonlinear viscoelasticity and relaxation phenomena of polymer solids

In the light of a three-chain model of statistical network theories of rubberlike elastic models, it is assumed that the free energy function of incompressible viscoelastic polymer solids is a separable, symmetric function of the principle stretch ratios and the hidden thermodynamic coordinates along the same directions. This assumption leads to a characterization of those viscoelastic polymer solids which exhibit the property of factorizability between the time and strain functions.

Peng, S. T. J.↗