Search NASA⌕ Search

Engineering topics

Landen, O.

Publications and source records attributed to Landen, O..

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Diagnosing the origin and impact of low-mode asymmetries in ignition experiments at the National Ignition Facility

Inertial confinement fusion ignition requires high inflight shell velocity, good energy coupling between the hotspot and shell, and high areal density at peak compression. Three-dimensional asymmetries caused by imperfections in the drive symmetry or target can grow and damage the coupling and confinement. Recent high-yield experiments have shown that low-mode asymmetries are a key degradation mechanism and contribute to variability. Here we show the experimental signatures and impacts of asymmetry change with increasing implosion yield given the same initial cause. This letter has implications for improving robustness to a key degradation in ignition experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Reduced mixing in inertial confinement fusion with early-time interface acceleration

In inertial confinement fusion (ICF) implosions, the interface between the cryogenic DT fuel and the ablator is unstable to shock acceleration (the Richtmyer-Meshkov instability, RM) and constant acceleration (Rayleigh-Taylor instability, RT). Instability growth at this interface can reduce the final compression, limiting fusion burnup. If the constant acceleration is in the direction of the lighter material (negative Atwood number), the RT instability produces oscillatory motion that can stabilize against RM growth. Theory and simulations suggest this scenario occurred at early times in some ICF experiments on the National Ignition Facility, possibly explaining their favorable performance compared to one-dimensional simulations. In conclusion, this characteristic is being included in newer, lower adiabat designs, seeking to improve compression while minimizing ablator mixing into the fuel.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Measuring and simulating ice–ablator mix in inertial confinement fusion

Fuel–ablator mix has been established as a major performance degrading effect in the burning plasma regime of recent inertial confinement fusion (ICF) experiments. As such, the study of fuel–ablator mix with experiments and simulations can provide valuable insight for our understanding of these experiments and establish a path for even higher yields and increased robustness. Here we present a novel high-yield experimental ICF design that is motivated by recent experiments measuring ice–ablator mix with a CH ablator instead of a high-density carbon (HDC) ablator. Here we review these experiments in more detail and describe the modeling assumptions and parameters used to obtain agreement with the data from implosion and burn simulations with mix. Using this mix model calibrated a posteriori to the experimental data, we design an implosion that uses a CH ablator that is predicted to achieve better performance than a recent experiment that achieved net target gain of 1.5 in HDC. Because hydrodynamic instabilities are greatly reduced with this new design, we also expect a high reproducibility at the same implosion adiabat as current record yield experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Extensions of a classical mechanics “piston-model” for understanding the impact of asymmetry on ICF implosions: The cases of mode 2, mode 2/1 coupling, time-dependent asymmetry, and the relationship to coast-time

As long suspected, low mode asymmetry in inertially confined fusion (ICF) implosions has been implicated as a performance limiting factor [Casey et al., “Evidence of three-dimensional asymmetries seeded by high-density carbon-ablator nonuniformity in experiments at the national ignition facility,” Phys. Rev. Lett. 126, 025002 (2021)]. Recently a non-linear, but solvable, theory [Hurricane et al., “An analytic asymmetric-piston model for the impact of mode-1 shell asymmetry on ICF implosions,” Phys. Plasmas 27, 062704 (2020)] based upon the simple picture of a pair of asymmetric pistons has generated new insights and provided some practical formulas for estimating the degradation of an implosion due to mode-1 asymmetry and demonstrated a previously unrecognized connection between measured hot-spot drift velocity, nuclear down-scatter ratio asymmetry, and the concept of residual kinetic energy (RKE). Asymmetry of the implosion “shell,” as opposed to asymmetry of the hot-spot, was key to the classical mechanics model because the majority of the kinetic energy in an implosion is carried by the shell. Herein, the two-piston model is extended to a six-piston model in order to capture mode-2 asymmetry and coupling between mode-1 and mode-2. A key result of this new six-piston model is that the weighted harmonic mean of shell areal density is the fundamental quantity that determines the RKE and performance degradations for a three-dimensional implosion. Agreement is found between the scalings coming from the theory and ICF implosion data from the National Ignition Facility and to large ensembles of detailed simulations. The connection between the piston model's dependence upon the radius of peak velocity and coast-time is also highlighted in this paper. Finally, by extending the two-piston model to include time-dependent “swing,” it is shown in the Appendix that the shell asymmetry at the time of stagnation dominates the solution for RKE.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Achieving record hot spot energies with large HDC implosions on NIF in HYBRID-E

HYBRID-E is an inertial confinement fusion implosion design that increases energy coupled to the hot spot by increasing the capsule scale in cylindrical hohlraums while operating within the current experimental limits of the National Ignition Facility. HYBRID-E reduces the hohlraum scale at a fixed capsule size compared to previous HYBRID designs, thereby increasing the hohlraum efficiency and energy coupled to the capsule, and uses the cross-beam energy transfer (CBET) to control the implosion symmetry by operating the inner (23° and 30°) and outer (44° and 50°) laser beams at different wavelengths (Δλ> 0). Small case to capsule ratio designs can suffer from insufficient drive at the waist of the hohlraum. We show that only a small amount of wavelength separation between the inner and outer beams (Δλ1-2 Å) is required to control the symmetry in low-gas-filled hohlraums (0.3 mg/cm3 He) with enough drive at the waist of the hohlraum to symmetrically drive capsules 1180 μm in outer radius. This campaign is the first to use the CBET to control the symmetry in 0.3 mg/cm3 He-filled hohlraums, the lowest gas fill density yet fielded with Δλ> 0. We find a stronger sensitivity of hot spot P2 in μm per Angstrom (40–50 μm/Å wavelength separation) than observed in high-gas-filled hohlraums and previous longer pulse designs that used a hohlraum gas fill density of 0.6 mg/cm3. There is currently no indication of transfer roll-off with increasing Δλ, indicating that even longer pulses or larger capsules could be driven using the CBET in cylindrical hohlraums. We show that the radiation flux symmetry is well controlled during the foot of the pulse, and that the entire implosion can be tuned symmetrically in the presence of the CBET in this system, with low levels of laser backscatter out of the hohlraum and low levels of hot electron production from intense laser–plasma interactions. Radiation hydrodynamic simulations can accurately represent the early shock symmetry and be used as a design tool, but cannot predict the late-time radiation flux symmetry during the peak of the pulse, and semi-empirical models are used to design the experiments. Deuterium–tritium (DT)-layered tests of 1100 μm inner radius implosions showed performance close to expectations from simulations at velocities up to ~360 km/s, and record yields at this velocity, when increasing the DT fuel layer thickness to mitigate hydrodynamic mixing of the ablator into the hot spot as a result of defects in the ablator. However, when the implosion velocity was increased, mixing due to these defects impacted performance. The ratio of measured to simulated yield for these experiments was directly correlated with the level of observed mixing. These simulations suggest that reducing the mixing, e.g., by improving the capsule defects, could result in higher performance. In addition, future experiments are planned to reduce the coast time at this scale, delay between the peak compression and the end of the laser, to increase the hot spot convergence and pressure. To reduce the coast time by several hundred ps compared to the 1100 μm inner radius implosions, HYBRID-E has also fielded 1050 μm inner radius capsules, which resulted in higher hot spot pressure and a fusion energy yield of ~170 kJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

The effects of multispecies Hohlraum walls on stimulated Brillouin scattering, Hohlraum dynamics, and beam propagation

We report experiments and simulations have been conducted to investigate the efficacy of Ta 2 O 5 -lined Hohlraum walls at reducing stimulated Brillouin backscattering (SBS) as well as any subsequent effects on the Hohlraum dynamics and capsule implosions in indirect drive experiments at the National Ignition Facility. Using a 1.1 MJ 400 TW, 351 nm, shaped laser pulse, we measure a 5× reduction in SBS power in the peak of the pulse from the wall on the outer 50° cone beams. The SBS spectrum indicates a reduction in the high-Z spectral signature when using multispecies wall materials. Detailed hydrodynamic simulations were performed using different heat conduction models with flux limiters. Additional simulations were performed on the plasma maps using the 3D parallel paraxial code pF3D to compare backscatter powers between the pure Au and Ta 2 O 5 -lined Hohlraums. Further analysis, using hydrodynamically equivalent plasmas, shows that the SBS reduction is clearly a result of the added ion Landau damping caused by the oxygen ions and not from differences in plasma conditions. The experimental and simulation results also show an increase in the wall plasma expansion when using the Ta 2 O 5 liner leading to a 70% more oblate implosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A magnetic particle time-of-flight (MagPTOF) diagnostic for measurements of shock and compression-bang time at the NIF [National Ignition Facility]

A magnetic particle time-of-flight (MagPTOF) diagnostic has been designed to measure shock- and compression-bang time using DHe-fusion protons and DD-fusion neutrons, respectively, at the National Ignition Facility (NIF). This capability, in combination with shock-burn weighted areal density measurements, will significantly constrain the modeling of the implosion dynamics. This design is an upgrade to the existing particle time-of-flight (pTOF) diagnostic, which records bang times using DD or DT neutrons with an accuracy better than ±70 ps [H. G. Rinderknecht et al., Rev. Sci. Instrum. 83, 10D902 (2012)]. The inclusion of a deflecting magnet will increase DHe-proton signal-to-background by a factor of 1000, allowing for the first time simultaneous measurements of shock and compression-bang times in DHe-filled surrogate implosions at the NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Understanding asymmetries using integrated simulations of capsule implosions in low gas-fill hohlraums at the National Ignition Facility

Current capsule implosions at the National Ignition Facility (NIF) using high-density-carbon ablators and laser energies close to 2 MJ have shown neutron yields in excess of 50 kJ. Improving on this performance requires understanding of the different degradation mechanisms. For many NIF implosions, nuclear diagnostic signatures have inferred residual hot-spot velocities that correlate with fuel areal density variations consistent with a low-order mode-1 asymmetry. A current working hypothesis attributes these asymmetries to a combination of beam to beam variations in the laser delivery and possibly coupling to target features, such as the diagnostic holes needed for x-ray imaging. Recently, a new source has been identified, thickness variation in the ablator shell. To gain better understanding and eventually mitigate the causes of <ρR> asymmetries, 3D integrated simulations using the actual delivered laser powers are needed. To capture the effect of the diagnostic holes (DHs) using direct numerical simulation would require significantly large computational resources. Instead, our 3D simulations make use of a subgrid model developed using highly-resolved 2D simulations that include several details of the DH engineering complexity. Simulations of NIF shots using hohlraums without DHs, to isolate the effect of beam-to-beam variations, reproduce fairly well the observed nuclear diagnostic signatures. Similarly, reasonable agreement between data and simulations is also obtained in the presence of diagnostic holes. To account for the remaining discrepancies a sensitivity study of ablator thickness variation showed that 1% thickness asymmetries are comparable in effect to 1% peak drive mode-1 asymmetries. Furthermore, this study identified sensitivity to variations in the imbedded doped layer (needed to shield the DT ice from the high energy x-rays generated in the hohlraum) thickness even when the inner and outer surface of the ablator are perfectly spherical.

radiation hydrodynamics↗
DOE OSTI2020

A novel method to measure ion density in ICF experiments using x-ray spectroscopy of cylindrical tracers

The indirect drive approach to inertial confinement fusion has undergone important advances in the past few years. Improvements in temperature and density diagnostic methods are leading to more accurate measurements of the plasma conditions inside the Hohlraum and therefore to more efficient experimental designs. The implementation of dot spectroscopy has proven to be a versatile approach to extracting space- and time-dependent electron temperatures. In this method, a microdot of a mid-Z material is placed inside the Hohlraum and its K-shell emission spectrum is used to determine the plasma temperature. However, radiation transport of optically thick lines acting within the cylindrical dot geometry influences the outgoing spectral distribution in a manner that depends on the viewing angle. This angular dependence has recently been studied in the high energy density regime at the OMEGA laser facility, which allowed us to design and benchmark appropriate radiative transfer models that can replicate these geometric effects. By combining these models with the measurements from the dot spectroscopy experiments at the National Ignition Facility, we demonstrate here a novel technique that exploits the transport effects to obtain time-resolved measurements of the ion density of the tracer dots, without the need for additional diagnostics. Furthermore, we find excellent agreement between experiment and simulation, opening the possibility of using these geometric effects as a density diagnostic in future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Fill tube dynamics in inertial confinement fusion implosions with high density carbon ablators

Plasma jets, such as γ-ray burst jets, Herbig–Haro jets, μ-quasar jets, and active galactic nuclei jets, are found throughout the universe [S. Mendoza et al., Rev. Mex. Astron. Astrofis. 41, 453 (2005)]. Plasma jets are also present in indirect drive inertial confinement fusion experiments originating from the capsule's fill tube and occasionally from divots and voids in the capsules, particles on the exterior of the capsule, or from the tent holding the capsule in the target. This paper looks at two different gas-filled capsule implosions containing a plasma jet resulting from a capsule fill tube and fill channel, both of which utilized high density carbon ablators. Two models were developed, a drag and a snowplow model, which use the time-dependent motion of the injected mass through the hotspot to estimate the mass injected into the hotspot from the fill tube and channel, arriving at an average injected mass of ~84.5 ± 25.5 ng for the first experiment and 91 ± 20 ng for the second experiment. Furthermore, unlike previous methods to estimate fill tube injected mass, these techniques do not assume that the mixed mass is in thermal equilibrium with the hotspot or that the x-ray emission is only coming from within the hotspot itself. This paper also discusses the features seen in these experiments which include limb brightening in the shell for undoped ablators and flattening in the ablator from shadowing by the fill tube.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Measurements of enhanced performance in an indirect drive inertial confinement fusion experiment when reducing the contact area of the capsule support

Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. In this work, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 ×1016, 76% higher than the expected Y DT ∝V 7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

An analytic asymmetric-piston model for the impact of mode-1 shell asymmetry on ICF implosions

For many years, low mode asymmetry in inertially confined fusion (ICF) implosions has been recognized as a potential performance limiting factor, but analysis has been limited to using simulations and searching for data correlations. In this paper, an analytically solvable model based upon the simple picture of an asymmetric piston is presented. Asymmetry of the shell driving the implosion, as opposed to asymmetry in the hot-spot, is key to the model. The model provides a unifying framework for the action of mode-1 shell asymmetry and the resulting connections between various diagnostic signatures. A key variable in the model is the shell asymmetry fraction, f, which is related to the areal density variation of the shell surrounding the hot-spot. It is shown that f is simply related to the observed hot-spot mode-1 velocity and to the concept of residual energy in an implosion. The model presented in this paper yields explicit expressions for the hot-spot diameter, stagnation pressure, hot-spot energy, inertial confinement-time, Lawson parameter, hot-spot temperature, and fusion yield under the action of mode-1 asymmetry. Agreement is found between the theory scalings when compared to ICF implosion data from the National Ignition Facility and to large ensembles of detailed simulations, making the theory a useful tool for interpreting data. The theory provides a basis for setting tolerable limits on asymmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗