Engineering topics
Publications and source records attributed to Landis, Geoffrey A..
Imagine sailing across the hot plains of Venus! A design for a craft to do just this was completed by the COncurrent Multidisciplinary Preliminary Assessment of Space Systems (COMPASS) Team for the NASA Innovative Advanced Concepts (NIAC) project. The robotic craft could explore over 30 km of surface of Venus, driven by the power of the wind.
In the last few years, the concept that an ultra-lightweight probe could be sent to one of the nearby stars pushed by a laser beam reflecting from a lightweight sail has moved from science fiction into conceptual design. A candidate interstellar sail envisions a two- to three-gram "starchip" micro probe, flying past a planet of Proxima Centauri after a 20 year voyage. With the probe moving at 60,000 km/sec, the flyby encounter at the target planet is within 1 AU of the target planet at most a few hours, and in the case of an encounter with a planet of Proxima Centauri, is close to the star for only a few minutes. With current technology, no power system exists that can produce the required power with a mass of less than one gram.
As first analyzed by Hermann Bondi in 1957, matter with negative mass is consistent with the structure of Einstein's general theory of Relativity. Although initially the concept was considered just a theoretical curiosity, negative mass, or "exotic matter," is now incorporated into the body of mainstream physics in a number of forms. Negative mass has a number of rather non-intuitive properties, which, as first noted by Bondi, and then later commented on by Forward (1990), Landis (1991), and others, results in possible applications for propulsion requiring little, or possibly no, expenditure of fuel. As pointed out by Morris and Thorne (1988) and others, negative mass (or, more strictly, a violation of the null energy condition) is also a requirement for any proposed faster than light travel. This paper presents the basic theory of negative mass, the ways by which it can manifest in contemporary physical theory, and the counterintuitive properties that result, including possible uses for interstellar propulsion. Although negative mass has moved from a theoretical curiosity to a concept fundamental to the contemporary understanding of physics, it is still not clear whether bulk negative mass can be manufactured, or if it is limited to only appearing at the cosmological scale (e.g., “dark energy:) or in the quantum (e.g., Casimir vacuum) limit. If it can be manufactured, the propulsion applications would be significant.
As first analyzed by Hermann Bondi in 1957, matter with negative mass is consistent with the structure of Einstein's general theory of Relativity. Although initially the concept was considered just a theoretical curiosity, negative mass, or "exotic matter," is now incorporated into the body of mainstream physics in a number of forms. Negative mass has a number of rather non-intuitive properties, which, as first noted by Bondi, and then later commented on by Forward (1990), Landis (1991), and others, results in possible applications for propulsion requiring little, or possibly no, expenditure of fuel. As pointed out by Morris and Thorne (1988) and others, negative mass (or, more strictly, a violation of the null energy condition) is also a requirement for any proposed faster than light travel. This paper presents the basic theory of negative mass, the ways by which it can manifest in contemporary physical theory, and the counterintiutive properties that result, including possible uses for interstellar propulsion.Although negative mass has moved from a theoretical curiosity to a concept fundamental to the contemporary understanding of physics, it is still not clear whether bulk negative mass can be manufactured, or if it is limited to only appearing at the cosmological scale (e.g., "dark energy:) or in the quantum (e.g., Casimir vacuum) limit. If it can be manufactured, the propulsion applications would be significant.
In the last few years, the concept that an ultra-lightweight probe could be sent to one of the nearby stars pushed by a laser beam reflecting from a lightweight sail has moved from science fiction into conceptual design. The Breakthrough Starshot project envisions a two- to three-gram "starchip" micro probe, flying past a planet of Proxima Centauri after a 20 year voyage. With the probe moving at 60,000 km/sec, the flyby encounter at the target planet lasts at most a few hours. With current technology, no power system exists that can produce the required power with a mass of less than one gram.
The Triton Hopper is a NASA Innovative Advanced Concepts (NIAC) project to design a mission to not merely land, but repeatedly fly across the surface of Triton, utilizing the volatile surface ices (primarily nitrogen) as propellant for a radioisotope-heated thermal rocket engine to launch across the surface and explore all the moon's varied terrain. An engineering design study of the vehicle and mission was done. With a calculated range of 20 km per hop, equator-to-pole mobility can be achieved over a primary mission duration of 2 years. Using Nuclear Electric Propulsion for the transfer vehicle, the same concept can be applied for a mission to the surface of Pluto.
The harsh environment at the surface of Venus, with a low solar intensity, red-rich solar spectrum, high temperatures, and a corrosive acid environment, makes it a challenging location to use photovoltaics. For the design of photovoltaic power generation for future missions to Venus, solar arrays that can function at high temperatures under low light intensity must be developed, and a significant difficulty in this is achieving a long lifetime without degradation under Venus conditions. One issue that must be addressed is the encapsulation to protect the solar cells from the environment, and most particularly the transparent adhesive affixing the coverglass to the cells. In this paper the factors affecting the reliability and degradation of transparent silicone adhesives under Venus conditions are discussed.
By Einstein's general theory of relativity, gravity of a massive body deflects light, and thus the sun can be used as a lens. The focus of the sun's gravitational lens is about 550 AU (Astronomical Units). (The sun continues to act as a lens beyond this minimum; at longer distances, the focused light passes increasingly far from the solar limb.) A mission to the gravitational focus of the sun, beyond the edge of the solar system, but far closer than the nearest stars, could be a target for an interstellar precursor. Proposed methods of reaching the focal distance include electric propulsion or laser- or solar sails. An objective for such a mission is to use the gravitational lens to image and map an extrasolar planet.
Due to the bending of light by gravity, the gravity of sun forms a lens. In principle, a spacecraft sent to the distance of the solar gravitational focus could be used as a gravitational lens telescope. One example of such a mission would be to use the gravitational lens to image an extrasolar planet around a nearby star. The practical difficulties with this concept are discussed, and some approaches to mitigating these difficulties suggested.
NASA Glenn Research Center (GRC) has a long history related to the development of advanced power technology for space applications. This expertise covers the breadth of energy generation (photovoltaics, thermal energy conversion, etc.), energy storage (batteries, fuel cell technology, etc.), power management and distribution, and power systems architecture and analysis. Such advanced technology is now being developed for small satellite and cubesat applications and could have a significant impact on the longevity and capabilities of these missions. A presentation during the Pre-Conference Workshop will focus on various advanced power technologies being developed and demonstrated by NASA, and their possible application within the small satellite community.
The Triton Hopper is a concept for a vehicle to explore the surface of Neptunes moon Triton, which uses a radioisotope heated rocket engine and in-situ propellant acquisition. The initial Triton Hopper conceptual design stores pressurized Nitrogen in a spherical tank to be used as the propellant. The aim of the research was to investigate the benefits of storing propellant at ambient temperature and heating it through a thermal block during engine operation, as opposed to storing gas at a high temperature.
A multi-discipline team of experts from the National Aeronautics and Space Administration (NASA) developed Mars surface power system point design solutions for two conceptual missions. The primary goal of this study was to compare the relative merits of solar- versus fission-powered versions of each surface mission. First, the team compared three different solar power options against a fission power system concept for a sub-scale, uncrewed demonstration mission. The 4.5 meter (m) diameter pathfinder lander's primary mission would be to demonstrate Mars entry, descent, and landing techniques. Once on the Martian surface, the lander's In Situ Resource Utilization (ISRU) payload would demonstrate liquid oxygen propellant production using atmospheric resources. For the purpose of this exercise, location was assumed to be at the Martian equator. The three solar concepts considered included a system that only operated during daylight hours (at roughly half the daily propellant production rate of a round-the-clock fission design), a battery-augmented system that operated through the night (matching the fission concept's propellant production rate), and a system that operated only during daylight, but at a higher rate (again, matching the fission concept's propellant production rate). Including 30% mass growth allowance, total payload masses for the three solar concepts ranged from 1,116 to 2,396 kg, versus the 2,686 kg fission power scheme. However, solar power masses are expected to approach or exceed the fission payload mass at landing sites further from the equator, making landing site selection a key driver in the final power system decision. The team also noted that detailed reliability analysis should be performed on daytime-only solar power schemes to assess potential issues with frequent ISRU system on/off cycling. Next, the team developed a solar-powered point design solution for a conceptual four-crew, 500-day surface mission consisting of up to four landers per crewed expedition mission. Unlike the demonstration mission, a lengthy power outage due to the global dust storms that are known to occur on Mars would pose a safety hazard to a crewed mission. A similar fission versus solar power trade study performed by NASA in 2007 concluded that fission power was more reliable-with a much lower mass penalty-than solar power for this application. However, recent advances in solar cell and energy storage technologies and changes in operational assumptions prompted NASA to revisit the analysis. For the purpose of this exercise a particular landing site at Jezero Crater, located at 18o north latitude, was assumed. A fission power system consisting of four each 10 kW Kilopower fission reactors was compared to a distributed network of Orion-derived Ultraflex solar arrays and Lithium ion batteries mounted on every lander. The team found that a solar power system mass of about 9,800 kg would provide the 22 kilowatts (kW) keep-alive power needed to survive a dust storm lasting up to 120-days at average optical depth of 5, and 35 kW peak power for normal operations under clear skies. Although this is less than half the mass estimated during the 2007 work (which assumed latitudes up to 30o) it is still more than the 7,000 kg mass of the fission system which provides full power regardless of dust storm conditions.
A multi-discipline team of experts from the National Aeronautics and Space Administration (NASA) developed Mars surface power system point design solutions for two conceptual missions to Mars using In-situ resource utilization (ISRU). The primary goal of this study was to compare the relative merits of solar- versus fission-powered versions of each surface mission. First, the team compared three different solar-power options against a fission power system concept for a sub-scale, uncrewed demonstration mission. This “pathfinder” design utilized a 4.5 meter diameter lander. Its primary mission would be to demonstrate Mars entry, descent, and landing techniques. Once on the Martian surface, the lander’s ISRU payload would demonstrate liquid oxygen propellant production from atmospheric resources. For the purpose of this exercise, location was assumed to be at the Martian equator. The three solar concepts considered included a system that only operated during daylight hours (at roughly half the daily propellant production rate of a round-the-clock fission design), a battery-augmented system that operated through the night (matching the fission concept’s propellant production rate), and a system that operated only during daylight, but at a higher rate (again, matching the fission concept’s propellant production rate). Including 30% mass growth allowance, total payload masses for the three solar concepts ranged from 1,128 to 2,425 kg, versus the 2,751 kg fission power scheme. However, solar power masses increase as landing sites are selected further from the equator, making landing site selection a key driver in the final power system decision. The team also noted that detailed reliability analysis should be performed on daytime-only solar power schemes to assess potential issues with frequent ISRU system on/off cycling.
A multi-junction solar cell is provided and includes multiple semiconducting layers and an interface layer disposed between the multiple semiconducting layers. The interface layer is made from an interface bonding material that has a refractive index such that a ratio of a refractive index of each of the multiple semiconducting layers to the refractive index of the interface bonding material is less than or equal to 1.5.
The Triton Hopper is a concept for a global hopper vehicle which uses a radioisotope rocket engine and In-situ propellant acquisition to explore the surface of Neptune's moon, Triton. The current Triton Hopper concept stores heated Nitrogen in a spherical tank to be used as the propellant. The aim of the research was to investigate the benefits of storing propellant at ambient temperature and heating it through the use of a thermal block during engine operation, as opposed to storing gas at a high temperature. Lithium, Lithium Fluoride and Beryllium were considered as possible materials for the thermal block. A heat energy analysis indicated that a lithium thermal mass would provide the highest heat energy for a temperature change from 900 Celsius to -100 Celsius. A heat transfer analysis was performed for Nitrogen at -100 Celsius flowing through 1000 passages inside a 1kg lithium thermal block at a temperature of 900 Celsius. The system was analyzed as turbulent flow through a tube with constant surface temperature. The analysis indicated that the propellant reached a maximum temperature of 877 Celsius before entering the nozzle. At this exit temperature, the average specific impulse [I(sub sp)] of the engine was determined to be 157s. Previous studies for the stored heated gas concept suggest that the engine would have an average I(sub sp) of approximately 52s. Thus, the use of a thermal block concept results in a 200 percent engine performance increase. In addition, a tank sizing study was performed to determine if the concept is feasible in terms of mass requirements. The mass for a spherical carbon fiber COPV storing 35kg of nitrogen at an initial temperature of -100 Celsius and a pressure of 1000psia, was determined to be 7.2kg. The specific impulse analysis indicated that the maximum engine performance is obtained for a mass ratio of 5kg of Nitrogen per every 1kg of lithium thermal mass. Thus for 35kg of Nitrogen the total thermal mass would be 7kg. This brings the total mass of the system to 49.2.kg which is less than the 56kg landing payload capacity of the Triton Hopper. Finally, an insulation analysis using 10mm of MLI insulation indicated that a total of 22 watts of heat are lost to the environment. With the heat loss known, the power required to heat the thermal mass to 900 Celsius in 24 days was determined to be 2.15 watts. The study's results allowed us to conclude that the thermal mass concept is the better option due to the performance increase provided, the low power requirement and its compliance with the landing mass requirement of the Triton Hopper.
Use of high-power solar arrays, at power levels ranging from approximately 500 KW to several megawatts, has been proposed for a solar-electric propulsion (SEP) demonstration mission, using a photovoltaic array to provide energy to a high-power xenon-fueled engine. One of the proposed applications of the high-power SEP technology is a mission to rendezvous with an asteroid and move it into lunar orbit for human exploration, the Asteroid Retrieval mission. The Solar Electric Propulsion project is dedicated to developing critical technologies to enable trips to further away destinations such as Mars or asteroids. NASA needs to reduce the cost of these ambitious exploration missions. High power and high efficiency SEP systems will require much less propellant to meet those requirements.
Power for missions to Jupiter and beyond presents a challenging goal for photovoltaic power systems, but NASA missions including Juno and the upcoming Europa Clipper mission have shown that it is possible to operate solar arrays at Jupiter. This work analyzes photovoltaic technologies for use in Jupiter and outer planet missions, including both conventional arrays, as well as analyzing the advantages of advanced solar cells, concentrator arrays, and thin film technologies. Index Terms - space exploration, spacecraft solar arrays, solar electric propulsion, photovoltaic cells, concentrator, Fresnel lens, Jupiter missions, outer planets.
An overview of NASA missions and technology development efforts are discussed. Future spacecraft will need higher power, higher voltage, and much lower cost solar arrays to enable a variety of missions. One application driving development of these future arrays is solar electric propulsion.