Search NASA⌕ Search

Engineering topics

Lange, A. E.

Publications and source records attributed to Lange, A. E..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Low-cycle Fatigue and Dynamic Fracture in Gold Thin Films on SiN Supported Membranes

This slide presentation focuses on the dynamic mechanical response and fatigue behavior in sub-micron thick Au-films deposited onto amorphous Si(sub X)N(sub y) substrates, with spider-web geometry, that were subjected to forced vibration (3-axis random vibration with 2 kHz roll-off frequency). The work is to advance cyrogenic detectors that can operate at 100mK, that is required to create cryogenic detectors that are to search for present day signatures of the big bang.

fatigue↗
NASA NTRS2005

Bolometeric detector arrays for CMB polarimetry

We describe the development of antenna coupled bolometers for CMB polarization experiments. The necessary components of a bolometric CMB polarimeter - a beam forming element, a band defining filter, and detectors - are all fabricated on a silicon chip with photolithography.

TES bolometers↗
NASA NTRS2001

A measurement by BOOMERANG of multiple peaks in the angular power spectrum of the cosmic microwave background

This paper presents a measurement of the angular power spectrum of the Cosmic Microwave Background from l = 75 to l = 1025 (~10' to 5 degrees) from a combined analysis of four 150 GHz channels in the BOOMERANG experiment. The spectrum contains multiple peaks and minima, as predicted by standard adiabatic-inflationary models in which the primordial plasma undergoes acoustic oscillations.

BOOMERANG spectrum cosmos microwave↗
NASA NTRS1997

A monolithic bolometer array suitable for FIRST

The development of arrays of infrared bolometers that are suitable for use in the Far Infrared and Submillimeter Telescope (FIRST) mission is reported. The array architecture is based on the silicon nitride micromesh bolometer currently baselined for use in the case of the Planck mission. This architecture allows each pixel to be efficiently coupled to one or both polarizations and to one or more spatial models of radiation. Micromesh structures are currently being developed, coupled with transistor-edge sensors and read out by a SQUID amplifier. If these devices are successful, then the relatively large cooling power available at 300 mK may enable a SQUID-based multiplexer to be integrated on the same wafer as the array, creating a monolithic, fully multiplexed, 2D array with relatively few connections to the sub-Kelvin stage.

Bock, J. J.↗
NASA NTRS1997

Cluster Observations for Combined X-Ray and Sunyaev-Zel'dovich Estimates of Peculiar Velocities and Distances

Measurements of the peculiar velocities of galaxy clusters with respect to the Hubble flow allow the determination of the gravitational field from all matter in the universe, not just the visible component. The Sunyaev-Zel'dovich (SZ) effect (the inverse-Compton scattering of cosmic microwave background photons by the hot gas in clusters of galaxies) allows these velocities to be measured without the use of empirical distance indicators. Additionally, because the magnitude of the SZ effect is independent of redshift, the technique can be used to measure velocities out to the epoch of cluster formation. The SZ technique requires a determination of the temperature of the hot cluster gas from X-ray observations, and measurements of the SZ effect at millimeter wavelengths to separate the contribution from the thermal motions within the gas from that of the cluster peculiax velocity. We have constructed a bolometric receiver, the Sunyaev-Zel'dovich Infrared Experiment, specifically to make measurements of the SZ effect at millimeter wavelengths in order to apply the SZ technique to peculiar velocity measurements. This receiver has already been used to set limits to the peculiar velocities of two galaxy clusters at z approx. 0.2. As a test of the SZ technique, the double cluster pair Abell 222 and 223 was selected for observation. Measurements of the redshifts of the two components suggest that, if the clusters are gravitationally bound, they should exhibit a relative velocity of 10OO km/ s, well above the expected precision of 200 km/ s (set by astrophysical confusion) that is expected from the SZ method. The temperature can be measured from ASCA data which we obtained for this cluster pair. However, in order to ensure that the temperature estimate from the ASCA data was not dominated by cooling flows within the cluster, we requested ROSAT HRI observations of this cluster pair. Analysis of the X-ray properties of the cluster pair is continuing by combining the ROSAT observations funded under this proposal, archival PSPC data and our own PI ASCA data. The imaging data shows that neither cluster has a strong cooling flow, although A223 is the more compact of the two components. A223 also has a sub-cluster projected 1 Mpc to the North. The observed properties of this cluster pair are strikingly similar to those of the well-studied pair of A399 and A401 which are widely believed to be interacting and are in the initial stages of merging. This strengthens our selection of this cluster pair as a test for cluster peculiar motions. Combining these X-ray observations with SUZIE measurements of the SZ effect will provide important constraints on cluster merger models. This part of the program has been heavily delayed by bad weather at Mauna Kea, however SZ observations were obtained in November 1997 as part of a separately funded effort. These data are currently being analyzed.

Lange, A. E.↗
NASA NTRS1996

Far-infrared emissivity measurements of reflective surfaces

An instrument developed to measure the emissivity of reflective surfaces by comparing the thermal emission of a test sample to that of a reference surface is reported. The instrument can accurately measure the emissivity of mirrors made from lightweight thermally insulating materials such as glass and metallized carbon fiber reinforced plastics. Far infrared measurements at a wavelength of 165 micrometers are reported. The instrument has an absolute accuracy of Delta epsilon = 9 x 10(exp -4) and can reproducibly measure an emissivity of as small as 2 x 10(exp -4) between flat reflective surfaces. The instrument was used to measure mirror samples for balloon-borne and spaceborne experiments. An emissivity of (6.05 +/- 1.24) x 10(exp -3) was measured for gold evaporated on glass, and (6.75 +/- 1.17) x 10(exp -3) for aluminum evaporated on glass.

Xu, J.↗
NASA NTRS1996

Bolometric detector systems for IR and mm-wave space astronomy

Recent developments in bolometric detector systems for millimeter and submillimeter wave space astronomy are described. Current technologies meet all the requirements for the high frequency instrument onboard the cosmic background radiation anisotropy satellite/satellite for the measurement of background anisotropies (COBRAS/SAMBA) platform. It is considered that the technologies that are currently being developed will significantly reduce the effective time constant and/or the cooling requirements of bolometric detectors. These technologies lend themselves to the fabrication of the large format arrays required for the Far Infrared and Submillimeter Space Telescope (FIRST). The scientific goals and detector requirements of the COBRAS/SAMBA platform that will use infrared bolometers are reviewed and the baseline detector system is described, including the feed optics, the infrared filters, the cold amplifiers and the warm readout electronics.

Church, S. E.↗
NASA NTRS1996

Infrared bolometers with silicon nitride micromesh absorbers

Sensitive far infrared and millimeter wave bolometers fabricated from a freestanding membrane of low stress silicon nitride are reported. The absorber, consisting of a metallized silicon nitride micromesh thermally isolated by radial legs of silicon nitride, is placed in an integrating cavity to efficiently couple to single mode or multiple mode infrared radiation. This structure provides low heat capacity, low thermal conduction and minimal cross section to energetic particles. A neutron transmutation doped Ge thermister is bump bonded to the center of the device and read out with evaporated Cr-Au leads. The limiting performance of the micromesh absorber is discussed and the recent results obtained from a 300 mK cold stage are summarized.

Bock, J. J.↗
NASA NTRS1995

Measurements of the millimeter-wave spectrum of interstellar dust emission

We report measurements of the differential brightness of interstellar dust emission near the Galactic plane and at high Galactic latitudes. The data were obtained as part of a program to measure anisotropy in the cosmic microwave background (CMB). The measurements were made with a 0.5 deg beam size and a 1.3 deg sinusoidal chop, in broad bands (Delta nu/nu approximately 0.3) centered near frequencies of 6, 9, and 12 cm(exp -1). A measurement made toward the Galactic plane, at longitude 1 = 23.7 deg, is compared with the contrast observed in the 100 micrometers IRAS data. Assuming the dust emission has a brightness I(sub nu) proportional to nu(sup n)B(sub nu)(T(sub d)), where B(sub nu) is the Planck function, a best fit yields n = 1.6 +/- 0.4, T(sub d) = 24 +/- 5 K. In a region near the star mu Pegasi (mu PEG l = 91 deg, b = -31 deg), the comparison of our data with the 100 micrometers IRAS data yields n = 1.4 +/- 0.4, and T(sub d) = 18 +/- 3 K. In a second region near the star gamma Ursa Minoris (GUM l = 108 deg, b = 41 deg), an upper limit is placed on contrast in dust emission. This upper limit is consistent with spectrum measured at mu PEG and the IRAS 100 micrometer emission contrast at GUM, which is approximately 8 times lower than mu PEG.

Fischer, M. L.↗
NASA NTRS1994

Measurements of anisotropy in the cosmic microwave background radiation at degree angular scales near the stars Sigma Herculis and Iota Draconis

We present results from two four-frequency observations centered near the stars Sigma Herculis and Iota Draconis during the fourth flight of the Millimeter-wave Anisotropy eXperiment (MAX). The observations were made of 6 deg x 0.6 deg strips of the sky with a 1.4 deg peak to peak sinusoidal chop in all bands. The full width at half maximum (FWHM) beam sizes were calculated 0.55 deg +/- 0.05 deg at 3.5/cm and a 0.75 deg +/- 0.05 deg at 6, 9, and 14/cm. Significant correlated structures were observed at 3.5, 6, and 9/cm. The spectra of these signals are inconsistent with thermal emission from known interstellar dust populations. The extrapolated amplitudes of synchrotron and free-free emission are too small to account for the amplitude of the observed structures. If the observed structures are attributed to cosmic microwave background (CMB) anisotropy with a Gaussian autocorrelation function and a coherence angle of 25 min, then the most probable values at Delta T/T(sub CMB) = 3.1 (sup +1.7 sub -1.3) x 10(exp -5) for the Sigma Herculis scan, and Delta T/T(sub CMB) = 3.3(sup +1.1 sub -1.1) x 10(exp -5) for the Iota Draconis scan (95% confidence upper, lower limits).

Clapp, A. C.↗
NASA NTRS1994

Measurements of anisotropy in the cosmic microwave background radiation at 0.5 deg angular scales near the star gamma ursae minoris

We present results from a four-frequency observation of a 6 deg x 0.6 deg strip of the sky centered near the star Gamma Ursae Minoris (GUM) during the fourth flight of the Millimeter-wave Anistropy experiment(MAX). The observation was made with a 1.4 deg peak-to-peak sinusoidal chop in all bands. The FWHM beam sizes were 0.55 deg +/- 0.05 deg at 3.5 per cm and 0.75 deg +/- 0.05 deg at 6, 9, and 14 per cm. During this observation significant correlated structure was observed at 3.5, 6 and 9 per cm with amplitudes similar to those observed in the GUM region during the second and third fligts of MAX. The frequency spectrum is consistent with cosmic microwave background (CMB) and inconsistent with thermal emission from interstellar dust. The extrapolated amplitudes of synchrotron and free-free emission are too small to account for the amplitude of the observed structure, If all of the structure is attributed to CMB anisotropy with a Gaussian autocorrelation function and a coherence angle of 25 min, then the most probable values of delta T/T(sub CMB) in the 3.5, 6 and 9 per cm bads are (4.3 +2.7/-1.6) x 10(exp -5), 2.8 (+4.3/-1/1) x 10(exp -5), and 3.5 (+3.0/-1.6) x 10(exp -5) (95% confidence upper and lower limits), respectively.

Devlin, M. J.↗
NASA NTRS1994

The Infrared Telescope in Space (IRTS)

The Infrared Telescope in Space (IRTS) is a cryogenically cooled small infrared telescope that will fly aboard the small space platform Space Flyer Unit. It will survey approximately 10% of the sky with a relatively wide beam during its 20 day emission. Four focal-plane instruments will make simultaneous observations of the sky at wavelengths ranging from 1 to 1000 microns. The IRTS will provide significant information on cosmology, interstellar matter, late-type stars, and interplanetary dust. This paper describes the instrumentation and mission.

Murakami, H.↗
NASA NTRS1994

The Far-Infrared Photometer on the Infrared Telescope in Space

We describe the design and calibration of the Far-Infrared Photometer (FIRP), one of four focal plane instruments on the Infrared Telescope in Space (IRTS). The FIRP will provide absolute photometry in four bands centered at 150, 250, 400, and 700 microns with spectral resolution wavelength/wavelength spread is approximately 3 and spatial resolution delta theta = 0.5 degrees. High sensitivity is achieved by using bolometric detectors operated at 300 mK in an AC bridge circuit. The closed-cycle He-3 refrigerator can be recycled in orbit. A 2 K shutter provides a zero reference for each field of view. More than 10% of the sky will be surveyed during the 3 week mission lifetime with a sensitivity of less than 10(exp -13) W per sq cm per sr per 0.5 degree pixel.

Lange, A. E.↗
NASA NTRS1994

A rocket-borne observation of the far-infrared sky at high Galactic latitude

We have measured the surface brightness of the far-infrared sky at lambda = 134, 154, and 186 micrometers at high Galactic latitude using a liquid-He-cooled, rocket-borne telescope. The telescope scanned over a 5 deg x 20 deg region which includes infrared cirrus, high-latitude molecular clouds, the starburst galaxy M82, and the H I Hole in Ursa Major, a region with uniquely low H I column density. The measured brightness at 134, 154, and 186 micrometers is well correlated with the 100 micrometers brightness measured by IRAS and, in regions excluding molecular clouds, with H I column density. The spectrum of the component correlated with H I is well fitted by a gray-body spectrum with a temperature of 16.4 (+2.3/-1.8) K, assuming an emissivity proportional to lambda(exp -2). Assuming a constant far-infrared dust emissivity per hydrogen nucleus, the ratio of the H2 column density to the velocity-integrated CO intensity in the high-latitude molecular cloud is NH2/W(sub co) = (1.6 +/- 0.3) x 10(exp 20)/sq cm/(K km/s). The residual brightness after subtracting the emission correlated with H I column density is lambda I(sub lambda)(154 micrometers) = (1.4 +/- 0.6) x 10(exp -12) W/sq cm/sr, yielding an upper limit to the far-infrared extragalactic background radiation of lambda I(sub lambda)(154 micrometers) is less than 2.6 x 10(exp -12) W/sq cm/sr.

Kawada, M.↗