Engineering topics

Langston, Sarah L.

Publications and source records attributed to Langston, Sarah L..

4 records

NASA NTRS2019

Effect of Phenolic Matrix Microcracking on the Structural Response of a 3-D Woven Thermal Protection System

The effect of microcracking in the phenolic matrix of a three-dimensional woven thermal protection system (TPS) and the resulting material stiffness reduction was studied via a comparison of finite element analysis results from a linear analysis and an iterative linear analysis. A TPS is necessary to protect space vehicles from the aerodynamic heating of planetary entry. The Heatshield for Extreme Entry Environment Technology (HEEET) project has developed a TPS for use in high heat-flux and pressure missions. The material is a dual-layer continuous dry weave, which is then infiltrated with a low-density phenolic resin matrix to form a rigid ablator. The phenolic resin matrix does not have structural load transfer requirements, and testing has shown that the phenolic resin can fully satisfy thermal requirements when the matrix contains microcracks. Due to high stresses in the through-the-thickness direction of the material, phenolic microcracks may form in the matrix material, which would result in a reduction of stiffness. An exploratory study was conducted to determine if reduction in material stiffness would change the load paths and/or decrease the structural margins. A comparison was performed between a linear finite element analysis that did not take into account phenolic microcracking and an iterative linear finite element analysis that accounted for propagation of phenolic microcracking. Four subcases using varying assumptions were analyzed and the results indicate that the assumed strength at which the phenolic microcracking propagates was the critical parameter for determining the extent of microcracking in the phenolic matrix. Phenolic microcracking does not have an adverse effect on the structural response of the test article and is not a critical failure.

Langston, Sarah L.↗

NASA NTRS2018

Optimization of a Multifunctional Hot Structure Aeroshell for Mars Entry

Vehicle size and weight are driving cost factors in sending vehicles into space because the cost of launch is directly related to the payload mass being delivered. Vehicle size and weight have a larger impact on deep- space missions compared to sending a payload to low Earth orbit due to the extra fuel and supplies required to complete the longer duration mission. One area of study for possible vehicle volume or weight reduction is the thermal protection system (TPS) of a vehicle. Hot structures have been proposed as a TPS concept which can carry both primary structural loads and thermal loads. The use of hot structures on a Mars entry vehicle may be feasible and have potential volume and weight savings over the current state of the art ablative TPS technology. A preliminary trade study was performed on a mid lift-to-drag aeroshell Mars entry concept vehicle; comparing the weight and skin thickness of a vehicle using ablative TPS with a vehicle using hot structures. Independent thermal and structural analyses were performed to determine the minimum mass designs. The goal of this study was to determine if the use of hot structures was feasible and had potential for significant vehicle volume and weight savings over the current state of the art. This trade study found that use of a hot structures leads to a feasible alternative to ablative TPS technology, with potential 53% weight and 22% thickness (volume) saving benefits that could enable future missions.

Langston, Sarah L.↗

NASA NTRS2017

Parametric Study of an Ablative TPS and Hot Structure Heatshield for a Mars Entry Capsule Vehicle

The National Aeronautics and Space Administration is planning to send humans to Mars. As part of the Evolvable Mars Campaign, different en- try vehicle configurations are being designed and considered for delivering larger payloads than have been previously sent to the surface of Mars. Mass and packing volume are driving factors in the vehicle design, and the thermal protection for planetary entry is an area in which advances in technology can offer potential mass and volume savings. The feasibility and potential benefits of a carbon-carbon hot structure concept for a Mars entry vehicle is explored in this paper. The windward heat shield of a capsule design is assessed for the hot structure concept as well as an ablative thermal protection system (TPS) attached to a honeycomb sandwich structure. Independent thermal and structural analyses are performed to determine the minimum mass design. The analyses are repeated for a range of design parameters, which include the trajectory, vehicle size, and payload. Polynomial response functions are created from the analysis results to study the capsule mass with respect to the design parameters. Results from the polynomial response functions created from the thermal and structural analyses indicate that the mass of the capsule was higher for the hot structure concept as compared to the ablative TPS for the parameter space considered in this study.

Langston, Sarah L.↗

NASA NTRS2016

Optimization of a Hot Structure Aeroshell and Nose Cap for Mars Atmospheric Entry

The National Aeronautics and Space Administration (NASA) is preparing to send humans beyond Low Earth Orbit and eventually to the surface of Mars. As part of the Evolvable Mars Campaign, different vehicle configurations are being designed and considered for delivering large payloads to the surface of Mars. Weight and packing volume are driving factors in the vehicle design, and the thermal protection system (TPS) for planetary entry is a technology area which can offer potential weight and volume savings. The feasibility and potential benefits of a ceramic matrix composite hot structure concept for different vehicle configurations are explored in this paper, including the nose cap for a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) and an aeroshell for a mid lift-to-drag (Mid L/D) concept. The TPS of a planetary entry vehicle is a critical component required to survive the severe aerodynamic heating environment during atmospheric en- try. The current state-of-the-art is an ablative material to protect the vehicle from the heat load. The ablator is bonded to an underlying structure, which carries the mechanical loads associated with entry. The alternative hot structure design utilizes an advanced carbon-carbon material system on the outer surface of the vehicle, which is exposed to the severe heating and acts as a load carrying structure. The preliminary design using the hot structure concept and the ablative concept is determined for the spherical nose cap of the HIAD entry vehicle and the aeroshell of the Mid L/D entry vehicle. The results of the study indicate that the use of hot structures for both vehicle concepts leads to a feasible design with potential weight and volume savings benefits over current state-of-the-art TPS technology that could enable future missions.

Langston, Sarah L.↗