Search NASA⌕ Search

Engineering topics

Larbalestier, D. C.

Publications and source records attributed to Larbalestier, D. C..

At least 19 records

Property Variations in Modern REBCO Coated Conductors from Multiple Manufacturers

The complex, multilayer structure of REBCO Coated Conductor (CC) poses significant challenges in the fabrication of high magnetic field devices where large stresses may initiate various forms of damage. Our goal is to peer below the cartoon representations of CC so that, amongst other things, we might better understand whether a CC from one manufacturer is interchangeable with that from another. This involves knowledge of a broad range of electromagnetic, geometric, microstructural, and J c (θ,B,T) properties, and their variations that collectively pose challenges for the fault tolerance of REBCO CC devices. Accordingly, comparative measurements of J c , visualization of flux penetration with Magneto-Optical Imaging (MOI), tape geometry from Scanning Electron Microscopy (SEM) of polished cross-sections, and extensive optical microscopy was performed on recently purchased samples from multiple manufacturers. Our analyses reveal many deviations from or characteristics absent from manufacturers’ specifications, while a comparison of different manufacturers’ mechanically and laser slit tapes shows a diverse array of slitting characteristics amongst the manufacturers and variation in properties those made to the same specification. Laser slit tapes from several manufacturers reveal ablated edges with damaged regions extending up to 50 μm, comparable to the damaged region found in the mechanically slit CC of this study. Overall, the aim of this study is to flesh out appropriate ways to understand the real conductor below the manufacturers’ cartoons to avoid surprises in our REBCO CC coil development program. The goal of this work was to perform a broad array of characterizations of the type needed for validation of purpose for making high field magnets: to our surprise we found a wide range of properties which greatly impact the mechanical strength and electromagnetic performance of solenoids composed of these conductors and reinforced the need for a broad characterization program for each conductor prior to its implementation.

Bradford, G.↗

Rapid assessment of REBCO CC angular critical current density J c (B, T = 4.2 K, θ) using torque magnetometry up to at least 30 tesla

Abstract Detailed design of REBa 2 Cu 3 O 7 − x (REBCO)-based magnets ideally relies on knowledge of the full angular and wide temperature range characterization of the critical current I c of the REBCO coated conductors (CC) at high magnetic fields. In practice, however, obtaining I c ( B , T , θ ) data by the commonly used electrical transport technique is expensive, tedious, and difficult, due to high critical current values that exceed 2000 A for B | | a b -plane ( θ = 90 deg). The conductors are often damaged during angular transport measurements at angles approaching the ab -plane. Therefore, so far, REBCO magnets have been designed without full I c ( B , T , θ ) data sets. Here, we present J c ( B , T , θ ) results for more than twenty samples of CC all made to the same advanced pinning specification produced by SuperPower Inc. For this, we employed torque magnetometry, benchmarking the results to transport I c measurements mostly made away from ab -plane, finding good agreement with scaling factors ≈1–1.3. What is striking is the huge variety of properties exhibited by the samples, even for CC made recently. Given the huge attention now being paid to the effects of screening currents and to the torques generated by offsets between the tape plane and the local magnetic field vector, our data set suggests some caution in detailed design of such magnets without having data of the type presented here.

Physics↗

Correlation of critical current density to quasi-biaxial texture and grain boundary cleanliness in fully dense Bi-2212 wires

The distinctive quasi-biaxial texture of Bi 2 Sr 2 CaCu 2 O x (Bi-2212) plays an important role in enabling high critical current density ($J_c$) in Bi-2212 round wires (RWs). Here we studied three over pressure heat treated wires with $J_c$ varying by a factor of ~10, all being fully dense. Using electron backscatter diffraction, we observed the differences in biaxial texture in these three wires. Transmission electron microscopy also revealed differences in grain boundary (GB) cleanliness and connectivity. These analyses showed that high $J_c$ is unambiguously correlated to the best biaxial texture, which is in turn correlated to slow cooling from the liquid melt into solid Bi-2212. However, at 4.2 K, there is a negligible difference in intragrain pinning in the three wires, suggesting that the $J_c$ variation by a factor of ~10 is primarily due to variable filament and intergrain connectivity. In this work, the principal determinants of intergrain connectivity is the quasi-biaxial texture and GB cleanliness. Overall, $J_c$ optimization of the Bi-2212 RW is a complex multi-variable process, but this study shows that maximizing the biaxial texture quality is an important first step in such an optimization process.

36 MATERIALS SCIENCE↗

Synthesis routes to eliminate oxide impurity segregation and their influence on intergrain connectivity in K-doped BaFe 2 As 2 polycrystalline bulks

The poor reproducibility of intergrain critical current density $J_c$ in Fe-based superconductors is often believed to result from uncontrolled grain boundary (GB) connectivity degraded by extrinsic factors such as the local or global impurity concentration or GB porosity or cracks. Earlier we found that Ba and K can appear as oxide impurities at GBs, along with GB-wetting FeAs. In this study, we evaluated how the sample preparation environment and purity of the starting materials influence the polycrystalline $J_c$ in K-doped BaFe 2 As 2 (Ba122) bulks. Using a high-performance glovebox, the oxygen and water levels were significantly reduced, eliminating traces of FeAs. We report oxide impurities and Ba (or K) segregation associated with oxygen in the starting materials were significantly reduced by using high purity starting materials. This combination essentially doubled the best $J_c$(4.2 K) values to 2.3 × 10 5 at self-field and 1.6 × 10 4 A cm –2 at 10 T and analytical scanning transmission electron microscopy showed no GB or O segregation in the best samples, but did show dark Z-contrast and distinct nanoscale porosity. Our work shows that an inert synthesis environment and high purity K and Ba do reduce current-blocking oxygen impurity and GB impurity phases, allowing deeper exploration of the role of extrinsic and intrinsic GB blocking effects in controlling the $J_c$ of polycrystalline Ba122.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evidence for preferential flux flow at the grain boundaries of superconducting RF-quality niobium

Here, the question of whether grain boundaries (GBs) in niobium can be responsible for lowered operating field (B RF ) or quality factor (Q 0 ) in superconducting radio-frequency (SRF) cavities is still controversial. Here, we show by direct DC transport across planar grain boundaries isolated from a slice of very large-grain SRF-quality Nb that vortices can preferentially flow along the grain boundary when the external magnetic field lies in the GB plane. However, increasing the misalignment between the GB plane and the external magnetic field vector markedly reduces preferential flux flow along GB. Importantly, we find that preferential GB flux flow is more prominent for a buffered chemical polished than for an electropolished bi-crystal. The voltage-current characteristics of GBs are similar to those seen in low angle grain boundaries of high temperature superconductors where there is clear evidence of suppression of the superconducting order parameter at the GB. While local weakening of superconductivity at GBs in cuprates and pnictides is intrinsic, deterioration of current transparency of GBs in Nb appears to be extrinsic, since the polishing method clearly affect the local GB degradation. The dependence of preferential GB flux flow on important cavity preparation and experimental variables, particularly, the final chemical treatment and the angle between the magnetic field and the GB plane, suggests two more reasons why real cavity performance can be so variable.

36 MATERIALS SCIENCE↗

An intermetallic powder-in-tube approach to increased flux-pinning in Nb 3 Sn by internal oxidation of Zr

We report on the development of multifilamentary Nb 3 Sn superconductors by a versatile powder-in-tube technique (PIT) that demonstrates a simple pathway to a strand with a higher density of flux-pinning sites that has the potential to increase critical current density beyond present levels. The approach uses internal oxidation of Zr-alloyed Nb tubes to produce Zr oxide particles within the Nb 3 Sn layer that act as a dispersion of artificial pinning centres (APCs). In this design, SnO 2 powder is mixed with Cu 5 Sn 4 powder within the PIT core that supplies the Sn for the A15 reaction with Nb1Zr filament tubes. Initial results show an average grain size of ~38 nm in the A15 layer, compared to the 90–130 nm of typical APC-free high-J c strands made by conventional PIT or Internal Sn processing. Furthermore, there is a shift in the peak of the pinning force curve from H/H irr of ~0.2 to ~0.3 and the pinning force curves can be deconvoluted into grain boundary and point-pinning components, the point-pinning contribution dominating for the APC Nb-1wt%Zr strands.

36 MATERIALS SCIENCE↗

Development of low angle grain boundaries in lightly deformed superconducting niobium and their influence on hydride distribution and flux perturbation

This study shows that low angle grain boundaries (LAGBs) can be created by small 5% strains in high purity (RRR ≥ 200) SRF-grade single crystalline niobium (Nb) and that these boundaries act as hydrogen traps as indicated by the distribution of niobium hydrides (Nb 1-x H x ). Nb 1-x H x is detrimental to superconducting radio frequency (SRF) Nb cavities due to its normal conducting properties at cavity operating temperatures. By designing a single crystal tensile sample extracted from a large grain (>5 cm) Nb ingot slice for preferred slip on one slip plane, LAGBs and dense dislocation boundaries developed. With chemical surface treatments following standard SRF cavity fabrication practice, Nb1-xHx phases were densely precipitated at the LAGBs upon cryogenic cooling (8-10 K/min). Micro-crystallographic analysis confirmed heterogeneous hydride precipitation, which included significant hydrogen atom accumulation in LAGBs. Magneto-optical imaging (MOI) analysis showed that these sites can then act as sites for both premature flux penetration and eventually flux trapping. However, this hydrogen related degradation at LAGBs did not completely disappear even after a 800 °C/2hrs anneal typically used for hydrogen removal in SRF Nb cavities. These findings suggest that hydride precipitation at a LAGB is facilitated by a non-equilibrium concentration of vacancy-hydrogen (H) complexes aided by mechanical deformation and the hydride phase interferes with the recovery process under 800°C annealing.

36 MATERIALS SCIENCE↗

Correlation of filament distortion and RRR degradation in drawn and rolled PIT and RRP Nb 3 Sn wires

PIT and RRP® Nb3Sn strands are being developed for high field accelerator magnet upgrades for the high luminosity LHC. Here we report a quantitative study of the shape and position of PIT filaments and RRP® sub-elements after rolling lengths of unreacted PIT and RRP® round wires to simulate cabling deformation. In the as-drawn condition, filament shape distortion occurs preferentially in the outer ring filaments. By contrast, rolling induces non-uniform shear bands that generate greater distortion of inner ring filaments. By making a full digitization of the shapes of all filaments, we find that a critical distortion occurs for thickness reductions between 10% and 20% when filament shapes in inner filament rings heavily degrade, especially in the vicinity of the strong 45° shear bands imposed by the rolling. It is well known that maintaining diffusion barrier integrity is vital to retaining adequate RRR in the stabilizing copper needed for magnet stability. Diffusion barrier breaks occur preferentially in these distorted inner filaments and drive local Sn leakage during reaction, increasing RRR degradation.

36 MATERIALS SCIENCE↗

Significant enhancement of compositional and superconducting homogeneity in Ti rather than Ta-doped Nb 3 Sn

Nb 3 Sn wires are now very close to their final optimization but despite its classical nature, detailed understanding of the role of Ta and Ti doping in the A15 is not fully understood. Long thought to be essentially equivalent in their influence on H c2 , they were interchangeably applied. Here we show that Ti produces significantly more homogeneous chemical and superconducting properties. Despite Ta-doped samples having a slightly higher T c onset in zero-field, they always have a wider Tc-distribution. In particular, whereas the Ta-doped A15 has a T c -distribution extending from 18 down to 5-6 K (the lowest expected Tc for the binary A15 phase), the Ti-doped samples have no A15 phase with T c below ~12 K. The much narrower T c distribution in the Ti-doped samples has a positive effect on their in-field T c -distribution too, leading to an extrapolated μ0 H c2 (0) 2 Tesla larger than the Ta-doped one. Ti-doping also appears to be very homogeneous even when the Sn content is reduced in order to inhibit breakdown of the diffusion barriers in very high J c conductors. As a result, the enhanced homogeneity of the Ti-doped samples appears to result from its assistance of rapid diffusion of Sn into the filaments and by its incorporation into the A15 phase interchangeably with Sn on the Sn sites of the A15 phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comparison of growth texture in round Bi2212 and flat Bi2223 wires and its relation to high critical current density development

Why Bi₂Sr₂CaCu₂O x (Bi2212) allows high critical current density J c in round wires rather than only in the anisotropic tape form demanded by all other high temperature superconductors is important for future magnet applications. Here we compare the local texture of state-of-the-art Bi2212 and Bi2223 ((Bi,Pb)₂Sr₂Ca₂Cu₃O₁₀), finding that round wire Bi2212 generates a dominant a-axis growth texture that also enforces a local biaxial texture (FWHM <15°) while simultaneously allowing the c-axes of its polycrystals to rotate azimuthally along and about the filament axis so as to generate macroscopically isotropic behavior. By contrast Bi2223 shows only a uniaxial (FWHM <15°) c-axis texture perpendicular to the tape plane without any in-plane texture. Consistent with these observations, a marked, field-increasing, field-decreasing J c (H) hysteresis characteristic of weak-linked systems appears in Bi2223 but is absent in Bi2212 round wire. Growth-induced texture on cooling from the melt step of the Bi2212 J c optimization process appears to be the key step in generating this highly desirable microstructure.

Kametani, F.↗

Development of very high J c in Ba(Fe 1-x Co x ) 2 As 2 thin films grown on CaF 2

Ba(Fe 1-x Co x ) 2 As 2 is the most tunable of the Fe-based superconductors (FBS) in terms of acceptance of high densities of self-assembled and artificially introduced pinning centres which are effective in significantly increasing the critical current density, J c . Moreover, FBS are very sensitive to strain, which induces an important enhancement in critical temperature,T c , of the material. In this study we demonstrate that strain induced by the substrate can further improve J c of both single and multilayer films by more than that expected simply due to the increase in T c . The multilayer deposition of Ba(Fe 1-x Co x ) 2 As 2 on CaF 2 increases the pinning force density (F p =J c x μ₀H) by more than 60% compared to a single layer film, reaching a maximum of 84 GN/m 3 at 22.5 T and 4.2 K, the highest value ever reported in any 122 phase.

36 MATERIALS SCIENCE↗

Specific heat of Nb{sub 3}Sn: The case for a single gap

The important influence of multiple gaps in the superconductivity of MgB{sub 2} and Fe-based compounds, especially because of the possibility that manipulation of a second gap can significantly raise the upper critical field H{sub c2}, has refocused attention on Nb{sub 3}Sn because anomalies in both specific heat and point-contact tunneling studies have led to the proposal that Nb{sub 3}Sn is also a two-gap superconductor. Here, we search for evidence of the second gap in a careful study of the influence of the homogenization temperature on the sample uniformity. We show that it is very difficult to fabricate samples that are both homogeneous and stoichiometric. We find so-called “second-gap” anomalies disappear only after high temperature and long-term annealing. Such a well-annealed sample shows only a strong, electron-phonon-coupled, single-gap behavior. In contrast, samples reacted and annealed at lower temperatures, as in the earlier two-gap studies, show small chemical composition variations of the A15 phase. We propose that the second gap sightings are actually due to variation of T{sub c} within very difficult-to-fully homogenize samples. A curiosity of the A15 Nb{sub 3}Sn phase is that almost any mixture of Nb and Sn tries to form a stoichiometric A15 composition, but the residue of course contains off-stoichiometric A15, Nb, and other phases when the Nb:Sn ratio departs from the true 3:1 stoichiometry.

36 MATERIALS SCIENCE↗