Search NASA⌕ Search

Engineering topics

Larsen, R

Publications and source records attributed to Larsen, R.

A Hierarchical Control Architecture for a PEBB-Based ILC Marx Modulator

The idea of building power conversion systems around Power Electronic Building Blocks (PEBBs) was initiated by the U.S. Office of Naval Research in the mid 1990s. A PEBB-based design approach is advantageous in terms of power density, modularity, reliability, and serviceability. It is obvious that this approach has much appeal for pulsed power conversion including the International Linear Collider (ILC) klystron modulator application. A hierarchical control architecture has the inherent capability to support the integration of PEBBs. This has already been successfully demonstrated in a number of industrial applications in the recent past. This paper outlines the underlying concepts of a hierarchical control architecture for a PEBB-based Marx-topology ILC klystron modulator. The control in PEBB-based power conversion systems can be functionally partitioned into (three) hierarchical layers; system layer, application layer, and PEBB layer. This has been adopted here. Based on such a hierarchical partition, the interfaces are clearly identified and defined and, consequently, are easily characterised. A conceptual design of the hardware manager, executing low-level hardware oriented tasks, is detailed. In addition, the idea of prognostics is briefly discussed.

43 PARTICLE ACCELERATORS↗

Final Design of the SLAC P2 Marx Klystron Modulator

The SLAC P2 Marx has been under development for two years, and follows on the P1 Marx as an alternative to the baseline klystron modulator for the International Linear Collider. The P2 Marx utilizes a redundant architecture, air-insulation, a control system with abundant diagnostic access, and a novel nested droop correction scheme. This paper is an overview of the design of this modulator. There are several points of emphasis for the P2 Marx design. First, the modulator must be compatible with the ILC two-tunnel design. In this scheme, the modulator and klystron are located within a service tunnel with limited access and available footprint for a modulator. Access to the modulator is only practical from one side. Second, the modulator must have high availability. Robust components are not sufficient alone to achieve availability much higher than 99%. Therefore, redundant architectures are necessary. Third, the modulator must be relatively low cost. Because of the large number of stations in the ILC, the investment needed for the modulator components is significant. High-volume construction techniques which take advantage of an economy of scale must be utilized. Fourth, the modulator must be simple and efficient to maintain. If a modulator does become inoperable, the MTTR must be small. Fifth, even though the present application for the modulator is for the ILC, future accelerators can also take advantage of this development effort. The hardware, software, and concepts developed in this project should be designed such that further development time necessary for other applications is minimal.

43 PARTICLE ACCELERATORS↗

The ILC P2 Marx and Application of the Marx Topology to Future Accelerators

The SLAC P2 Marx is under development as the linac klystron modulator for the ILC. This modulator builds upon the success of the P1 Marx, which is currently undergoing lifetime evaluation. While the SLAC P2 Marx's (henceforth, 'P2 Marx') target application is the ILC, characteristics of the Marx topology make it equally well-suited for operation at different parameter ranges; for example, increased pulse repetition frequency, increased output current, longer pulse width, etc. Marx parameters such as the number of cells, cell capacitance, and component selection can be optimized for the application. This paper provides an overview of the P2 Marx development. In addition, the scalability of the Marx topology to other long-pulse parameter ranges is discussed.

43 PARTICLE ACCELERATORS↗

Oligomeric Dithienopyrrole-Thienopyrrolodione (DTP-TPD) Donor-Acceptor Copolymer for Organic Photovoltaics: Preprint

A new donor-acceptor copolymer system based upon a dithienopyrrole (DTP) donor moiety and a thienopyrrolodione (TPD) accepting moiety has been designed and synthesized for organic photovoltaic (OPV) applications. The TPD accepting moiety has recently gained significant attention in the OPV community and is being incorporated into a number of different polymer systems. In contrast, the DTP donormoiety has received only limited attention, likely due in part to synthetic difficulties relating to the monomer. In our hands, the bis(trimethyltin)-DTP monomer was indelibly contaminated with~5% of the mono-destannylated DTP, which limited the Stille polymerization with the dibromo-TPD monomer (>99% pure) to produce material with Mn~4130 g/mol (PDI = 1.10), corresponding to around eightrepeat units. Despite this limitation, UV-visible absorption spectroscopy demonstrates strong absorption for this material with a band gap of~1.6 eV. Cyclic voltammetry indicates a highest occupied molecular orbital (HOMO) energy level of -5.3 eV, which is much lower than calculations predicted. Initial bulk heterojunction OPV devices fabricated with the fullerene acceptor phenyl C61 butyricacid methyl ester (PCBM) exhibit Voc~700 mV, which supports the deep HOMO value obtained from CV. These results suggest the promise of this copolymer system.

14 SOLAR ENERGY↗

Oligomeric Dithienopyrrole-Thienopyrroledione (DTP-TPD) Donor-Acceptor Copolymer for Organic Photovoltaics

A new donor-acceptor copolymer system based upon a dithienopyrrole (DTP) donor moiety and a thienopyrrolodione (TPD) accepting moiety has been designed and synthesized for organic photovoltaic (OPV) applications. The TPD accepting moiety has recently gained significant attention in the OPV community and is being incorporated into a number of different polymer systems. In contrast, the DTP donor moiety has received only limited attention, likely due in part to synthetic difficulties relating to the monomer. In our hands, the bis(trimethyltin)-DTP monomer was indelibly contaminated with {approx}5% of the mono-destannylated DTP, which limited the Stille polymerization with the dibromo-TPD monomer (>;99% pure) to produce material with M{sub n} {approx} 4130 g/mol (PDI = 1.10), corresponding to around eight repeat units. Despite this limitation, UV-visible absorption spectroscopy demonstrates strong absorption for this material with a band gap of {approx}1.6 eV. Cyclic voltammetry indicates a highest occupied molecular orbital (HOMO) energy level of -5.3 eV, which is much lower than calculations predicted. Initial bulk heterojunction OPV devices fabricated with the fullerene acceptor phenyl C61 butyric acid methyl ester (PCBM) exhibit V{sub oc} {approx} 700 mV, which supports the deep HOMO value obtained from CV. These results suggest the promise of this copolymer system.

14 SOLAR ENERGY↗

The"minimum information about an environmental sequence" (MIENS) specification

We present the Genomic Standards Consortium's (GSC) 'Minimum Information about an ENvironmental Sequence' (MIENS) standard for describing marker genes. Adoption of MIENS will enhance our ability to analyze natural genetic diversity across the Tree of Life as it is currently being documented by massive DNA sequencing efforts from myriad ecosystems in our ever-changing biosphere.

54 ENVIRONMENTAL SCIENCES↗

P1-Marx Modulator for the ILC

A first generation prototype, P1, Marx-topology klystron modulator has been developed at the SLAC National Accelerator Laboratory for the International Linear Collider (ILC) project. It is envisioned as a lower cost, smaller footprint, and higher reliability alternative to the present, bouncer-topology, baseline design. The application requires 120 kV (+/-0.5%), 140 A, 1.6 ms pulses at a rate of 5 Hz. The Marx constructs the high voltage pulse by combining, in series, a number of lower voltage cells. The Marx employs solid state elements; IGBTs and diodes, to control the charge, discharge and isolation of the cells. Active compensation of the output is used to achieve the voltage regulation while minimizing the stored energy. The P1-Marx has been integrated into a test stand with a 10 MW L-band klystron, where each is undergoing life testing. A review of the P1-Marx design and its operational history in the L-band test stand are presented.

43 PARTICLE ACCELERATORS↗

Next Generation Fast RF Interlock Module and ATCA Adapter for ILC High Availability RF Test Station Demonstration

High availability interlocks and controls are required for the ILC (International Linear Collider) L-Band high power RF stations. A new F3 (Fast Fault Finder) VME module has been developed to process both fast and slow interlocks using FPGA logic to detect the interlock trip excursions. This combination eliminates the need for separate PLC (Programmable Logic Controller) control of slow interlocks. Modules are chained together to accommodate as many inputs as needed. In the next phase of development the F3's will be ported to the new industry standard ATCA (Advanced Telecom Computing Architecture) crate (shelf) via a specially designed VME adapter module with IPMI (Intelligent Platform Management Interface). The goal is to demonstrate auto-failover and hot-swap for future partially redundant systems.

43 PARTICLE ACCELERATORS↗

Improved limit on the muon electric dipole moment

Three independent searches for an electric dipole moment (EDM) of the positive and negative muons have been performed, using spin precession data from the muon g-2 storage ring at Brookhaven National Laboratory. Details on the experimental apparatus and the three analyses are presented. Since the individual results on the positive and negative muons, as well as the combined result, d{sub {mu}}=(0.0{+-}0.9)x10{sup -19}e cm, are all consistent with zero, we set a new muon EDM limit, |d{sub {mu}}|<1.8x10{sup -19}e cm (95% C.L.). This represents a factor of 5 improvement over the previous best limit on the muon EDM.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗