Search NASA⌕ Search

Engineering topics

Lavine, E. S.

Publications and source records attributed to Lavine, E. S..

Axial confinement of wire array Z-pinch precursor plasmas by a pulsed magnetic mirror field

A novel wire-array Z-pinch platform has been developed to study the effect of a pulsed magnetic mirror field on a collisional high energy density plasma. The mirror is driven in series with the Z-pinch target and, therefore, scales with driver current. Axial confinement is observed based on visible imaging and axial flow velocity measurements. The presence of axial compressing J xB force is determined indirectly based on Thomson scattering and interferometry measurements and corroborated by three-dimensional extended-MHD simulations. Compared to non-magnetized wire array Z-pinch, a modified pulsed mirror configuration is observed to increase precursor plasma thermal energy density by about 30%. If optimized, such a configuration could potentially improve magnetized liner inertial fusion performance by reducing axial plasma end loss.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Applying Thomson scattering to diagnosing turbulent density and velocity fluctuations in a gas-puff z-pinch

The electron plasma wave feature (EPW) in the time-resolved Thomson scattering spectrum is used to obtain the local electron density in imploding high energy density gas-puff z-pinch plasmas. The optical setup was optimized to allow the relatively weak EPW feature obtained from 1 MA imploding neon gas-puff z-pinches to be seen above the continuum emission as well as the brighter ion acoustic wave (IAW) feature. Using a frequency-doubled Nd:YLF laser (E = 10 J, λ = 526.5 nm, Δt= 2.3 ns, spot size ~ 250 μm) and two visible light streak cameras, we determined the average electron density in the imploding plasma sheath 40 ns prior to stagnation to be n e = 2.5 × 10 18 /cm 3 . At pinch time, it reached n e = 1.7 × 10 19 /cm 3 . Here, the electron temperature during implosion measured via the IAW (approximately 50 eV) was four times lower than the implosion electron temperature measured via the EPW (approximately 200 eV), assuming that neither feature is affected by turbulent fluctuations in the plasma. In order for the electron temperatures inferred from the EPW and IAW spectral features to be self-consistent, we find that it is necessary to include velocity fluctuations in the analysis of the IAW feature peaks and corresponding density fluctuation in the peak widths of the EPW feature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of the imploding plasma sheath in triple-nozzle gas-puff z pinches

Gas-puff z-pinch implosions are characterized by the formation of a dense annular plasma shell, the sheath, that is driven to the axis by magnetic forces and therefore subject to the magneto-Rayleigh–Taylor instability. Here, the conditions within these sheaths are measured on the 1-MA COBRA generator at Cornell University for various gas species and initial fill densities. The gas-puff loads are initialized by a 7 cm diameter triple-nozzle gas valve assembly with concentric outer and inner annular nozzles and a central gas jet. Thomson scattering and laser interferometry provide spatially resolved flow, temperature, and electron density profiles midway through the implosion, while extreme ultraviolet pinhole cameras record the evolution of the plasma column and photoconducting diodes measure x-ray emission. Analysis of the scattering spectra includes a means of discriminating between thermal and non-thermal broadening to test for the presence of hydrodynamic turbulence. Two types of sheath profiles are observed, those with sharp discontinuities at the leading edge and those with smooth gradients. In both cases, non-thermal broadening is generally peaked at the front of the sheath and exhibits a characteristic decay length that roughly scales with the sheath ion mean free path. Here, we demonstrate that this non-thermal broadening term is inconsistent with laminar velocity gradients and is more consistent with dissipative turbulence driven by unstable plasma waves in a collisionless shock. The resulting differences in sheath profile are then set by the sheath ion collisionality in a manner consistent with recent 1D kinetic simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Liner implosion experiments driven by a dynamic screw pinch

This paper expands upon recent experimental results [Campbell et al., Phys. Rev. Lett. 125, 035001 (2020)], where thin-foil liner implosions were driven by a dynamic screw pinch (DSP) and found to have magneto-Rayleigh–Taylor instability (MRTI) amplitudes up to three times smaller than in implosions driven by a standard z-pinch (SZP). Here, the expanded discussion presented herein includes: (1) a detailed comparison of the MRTI growth measured in the experiment with that calculated from theory; (2) measurements of axial magnetic field injection into the liner interior prior to the implosion, as well as the subsequent compression of this field during the implosion; (3) an in-depth description of how the helical geometry of the DSP can result in earlier implosion and stagnation times relative to the SZP; and (4) particle-in-cell simulations showing different electron drift behavior in the anode–cathode gap of the DSP relative to the SZP, and how this difference may be related to the different current waveforms recorded during the experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Current polarity effects on laboratory plasma jets

Plasma jets produced by a pulsed power machine were investigated using Thomson scattering and other diagnostics in order to make detailed comparisons to simulations. These jets were produced from a 15 μm thick disc of Al foil on a 1.2 MA, 100 ns rise time, pulsed power machine. Experiments were performed with both a radially inward and a radially outward current ow in the Al foil to investigate the effects of voltage polarity in the experiments and determine how extended magnetohydrodynamic (XMHD) effects, such as the Hall effect, change the formation of the jet. We recorded Thomson scattering spectra with a low enough laser energy to not perturb the plasma, while providing a high enough signal to noise ratio to resolve the scattered features. This enabled the measurement of the electron temperature in the jet region of the plasma, 15.5±4 eV for both current polarities. Jets with a radially outward current ow were heated more from inverse bremsstrahlung when 10 J of laser energy was used, implying that these jets are denser than the ones with a radially inward current. This higher density was con rmed by interferometry measurements. Experimental results were compared with XMHD computer simulations, which predicted electron temperatures 1.5 to 3 σ above those measured, and significantly higher density than experiments in both polarities. In this paper, possible sources of this discrepancy are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion dynamics of triple-nozzle gas-puff z pinches on COBRA

Experiments on the 1-MA, 220-ns COBRA generator at Cornell University were conducted to provide detailed measurements of structured cylindrical gas-puff z pinches. In the experiments, a 7 cm diameter triple-nozzle gas valve assembly with concentric outer and inner annular nozzles and a central gas jet initialize the z-pinch load with various working gases, radial density profiles, and externally applied axial magnetic fields. Planar laser-induced fluorescence provides a measure of the initial neutral gas density of the load, while three-frame laser shearing interferometry and multi-frame extreme ultraviolet (XUV) cameras reveal the formation and propagation of a magneto-Rayleigh–Taylor (MRT) unstable shock layer. Implosion trajectories are compared to simple, experimentally informed models and found to be in good agreement. Differences in the structure of the accelerating plasma sheath and evolution of the MRT instability are observed for different gas species and axial magnetic field strengths, correlating with differences in pinch uniformity and x-ray emission. Here, the average instability growth is compared to linear MRT theory predictions using the instantaneous acceleration of the best-fit implosion models and characteristic instability wavelength, with the effective Atwood number and seed perturbation size as fit parameters. For high density argon center jets, ionization prior to the arrival of the imploding plasma sheath suggests a heating mechanism consistent with photoionization by XUV self-emission.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Implosion mediated gas-puff hybrid X-pinch

Imploding gas-puff z-pinches are efficient sources of intense X-rays. However, the unpredictable size, number, and location of hot-spots along the pinch axis make them unsuitable for applications such as point-projection radiography. Crossed wire or hybrid X-pinches on the other hand provide small, localized sources but require fast current rise times and must be reloaded after each pulse. In this letter, we present the first experimental demonstration of an implosion mediated gas-puff hybrid x-pinch in which an annular gas-puff implosion is shaped and focused onto pair of conical electrodes separated by a small gap. Here, this setup produces an intense X-ray source with controllable timing that can be operated with or without a central wire. Because the gas-puff implosion time determines the formation of the pinch, this configuration can continue to operate efficiently as a point X-ray source for longer current pulses than conventional x-pinches.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Stabilization of Liner Implosions via a Dynamic Screw Pinch

Magnetically driven implosions are susceptible to magnetohydrodynamic instabilities, including the magneto-Rayleigh-Taylor instability (MRTI). To reduce MRTI growth in solid-metal liner implo-sions, the use of a dynamic screw pinch (DSP) has been proposed [P. F. Schmit et al., Phys. Rev. Lett. 117, 205001 (2016)]. In a DSP con guration, a helical return-current structure surrounds the liner, resulting in a helical magnetic eld that drives the implosion. Here, we present the rst experimental tests of a solid-metal liner implosion driven by a DSP. Using the 1-MA, 100{200-ns COBRA pulsed-power driver, we tested three DSP cases (with peak axial magnetic elds of 2 T, 14 T, and 20 T) and a standard z-pinch (SZP) case (with a straight return-current structure and thus zero axial eld). The liners had an initial radius of 3.2 mm and were made from 650-nm-thick aluminum foil. Images collected during the experiments reveal that helical MRTI modes developed in the DSP cases, while non-helical (azimuthally symmetric) MRTI modes developed in the SZP case. Additionally, the MRTI amplitudes for the 14-T and 20-T DSP cases were smaller than in the SZP case. Speci cally, when the liner had imploded to half of its initial radius, the MRTI amplitudes for the SZP case and for the 14-T and 20-T DSP cases were, respectively, 1.1-0.3 mm, 0.7-0.2 mm, and 0.3-0.1 mm. Relative to the SZP, the stabilization obtained using the DSP agrees reasonably well with theoretical estimates.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Electron plasma wave Thomson scattering on laboratory plasma jets

Plasma jets created from a 15 lm thick Al foil on a 1 MA pulsed power machine were studied using a new electron plasma wave (EPW) Thomson scattering system in conjunction with previously developed ion acoustic wave (IAW) Thomson scattering and interferometry. These diagnostics give multiple ways of measuring the electron temperature and density of the jet. Analysis of the EPW feature found the on-axis density of the jet to be between 5 X 10 18 and 1.4 X 10 19 cm -3 , which either matched or was higher than interferometry measurements. Outside of the jet, both of these diagnostics measured a density of 7 X 10 17 cm -3 . On one shot, the EPW spectral feature showed two pairs of peaks within a 250 lm scattering length on the edge of the jet, which shows that the boundary of the jet ~1 mm radius jet is 0.1 mm. While electron temperature measurements of the plasma jet are complicated by the probe beam producing inverse bremsstrahlung heating of the jet, comparison of the electron temperature measured between IAW and EPW Thomson scattering showed the EPW feature to imply significantly higher electron temperatures than the IAW feature (e.g., 160 eV vs 70 eV in one case). Various sources of this discrepancy (for example, density gradients, collisions, and a lag in ionization) and their impact on the plasma are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of Triple Ar Gas Puff Z-Pinches on 0.9-MA, 200-ns COBRA

Ar gas puff z-pinch experiments were conducted on the 0.9 MA, 200 ns COBRA generator at Cornell University. In the experiments, a triple-nozzle gas valve was used to produce the zpinch load with concentric outer and inner gas puffs and a central gas jet. We used Planer Laser Induced Fluorescence (PLIF) to measure the initial gas profile of the load, two 4-frame 4-ns gated XUV cameras to image the imploding plasma, and filtered Photo- Conducting Diamond Detectors (PCDs) to measure the x-ray output. We have observed shock heating and/or photoionization of the dense center jet by the imploding plasma. With an outer to inner plenum pressure ratio of 1:3, de-acceleration of the imploding plasma occurred when the outer plasma shell imploded on the inner shell resulting in a stable implosion. By varying the plenum pressure for the center jet, the x-ray emission was optimized. In conclusion, an Ar K-shell x-ray (3-4 keV) yield of 77±17 J was produced at a current level of 0.87±0.2 MA and an implosion time of 200-ns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗