Search NASA⌕ Search

Engineering topics

Lavrik, Nickolay V.

Publications and source records attributed to Lavrik, Nickolay V..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Nanoscale Imaging and Measurements of Grain Boundary Thermal Resistance in Ceramics with Scanning Thermal Wave Microscopy

Material thermal conductivity is a key factor in various applications, from thermal management to energy harvesting. With microstructure engineering being a widely used method for customizing material properties, including thermal properties, understanding and controlling the role of extended phonon-scattering defects, like grain boundaries, is crucial for efficient material design. However, systematic studies are still lacking primarily due to limited tools. In this study, we demonstrate an approach for measuring grain boundary thermal resistance by probing the propagation of thermal waves across grain boundaries with a temperature-sensitive scanning probe. The method, implemented with a spatial resolution of about 100 nm on finely grained Nb-substituted SrTiO 3 ceramics, achieves a detectability of about 2 × 10 –8 K m 2 W –1 , suitable for chalcogenide-based thermoelectrics. The measurements indicated that the thermal resistance of the majority of grain boundaries in the STiO 3 ceramics is below this value. While there are challenges in improving sensitivity, considering spatial resolution and the amount of material involved in the detection, the sensitivity of the scanning probe method is comparable to that of optical thermoreflectance techniques, and the method opens up an avenue to characterize thermal resistance at the level of single grain boundaries and domain walls in a spectrum of microstructured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D‐Printed Carbon Nanoneedle Electrodes for Dopamine Detection in Drosophila

In vivo electrochemistry in small brain regions or synapses requires nanoelectrodes with long straight tips for submicron scale measurements. Nanoelectrodes can be fabricated using a Nanoscribe two-photon printer, but annealed tips curl if they are long and thin. We propose a new pulling-force strategy to fabricate a straight carbon nanoneedle structure. A micron-width bridge is printed between two blocks. The annealed structure shrinks during pyrolysis, and the blocks create a pulling force to form a long, thin, and straight carbon bridge. Parameterization study and COMSOL modeling indicate changes in the block size, bridge size and length affect the pulling force and bridge shrinkage. Electrodes were printed on niobium wires, insulated with aluminum oxide, and the bridge cut with focused ion beam (FIB) to expose the nanoneedle tip. Annealed needle diameters ranged from 400 nm to 5.25 μm and length varied from 50.5 μm to 146 μm. The electrochemical properties are similar to glassy carbon, with good performance for dopamine detection with fast-scan cyclic voltammetry. Nanoelectrodes enable biological applications, such as dopamine detection in a specific Drosophila brain region. Long and thin nanoneedles are generally useful for other applications such as cellular sensing, drug delivery, or gas sensing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Experimental evidence for the two-path description of neutron spin echo

Here, we describe an experiment that strongly supports a two-path interferometric model in which the spin-up and spin-down components of each neutron propagate coherently along spatially separated parallel paths in a typical neutron spin-echo small-angle scattering (SESANS) experiment. Specifically, we show that the usual semi-classical, single-path treatment of Larmor precession of a polarized neutron in an external magnetic field predicts a damping as a function of the spin-echo length of the SESANS signal obtained with a periodic phase grating when the transverse width of the neutron wave packet is finite. However, no such damping is observed experimentally, implying either that the Larmor model is incorrect or that the transverse extent of the wave packet is very large. In contrast, we demonstrate theoretically that a quantum-mechanical interferometric model in which the two mode-entangled (i.e., intraparticle entangled) spin states of a single neutron are separated in space when they interact with the grating accurately predicts the measured SESANS signal, which is independent of the wave packet width.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Reversible Binding Interfaces Made of Microstructured Polymer Brushes

The polymer brush architecture of the end-tethered polymer molecules is one of the most widely used efficient methods to regulate interfacial interactions in colloidal systems found in live matter and manufactured materials. Emerging applications of polymer brush structures require solutions to new tasks in the control of interfacial interactions. The rapid development of live cell manufacturing relies on scalable and efficient cell harvesting methods. Stimuli-responsive surfaces made of surface-grafted poly(N-isopropylacrylamide) (PNIPAM) can bind and detach the adherent cell upon changes in temperature and have been used for cell growth and harvesting. The applications are limited by the requirement to satisfy a range of PNIPAM coating characteristics that depend on the dimensions of the integrin complex in the cell membrane and the basal surface. The analysis of the microstructured surfaces, when adhesive and disjoining functions of the microdomains are decoupled, shows that many limitations of PNIPAM one-component coatings can be avoided by using a much broader range of structural characteristics of the microstructured interfaces composed of alternating disjoining PNIPAM domains and adhesive polymeric domains with cell-affinity functional groups. Temperature-controlled reversible adhesion to such microstructured interfaces is studied here experimentally with model systems of solid spherical particles and by employing simulations for solid and soft membranes interacting with the microstructured surfaces to mimic interactions with soft and solid disk-like particles.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A multi-material platform for imaging of single cell-cell junctions under tensile load fabricated with two-photon polymerization

We previously reported a single-cell adhesion micro tensile tester (SCAμTT) fabricated from IP-S photoresin with two-photon polymerization (TPP) for investigating the mechanics of a single cell-cell junction under defined tensile loading. A major limitation of the platform is the autofluorescence of IP-S, the photoresin for TPP fabrication, which significantly increases background signal and makes fluorescent imaging of stretched cells difficult. In this study, we report the design and fabrication of a new SCAμTT platform that mitigates autofluorescence and demonstrate its capability in imaging a single cell pair as its mutual junction is stretched. By employing a two-material design using IP-S and IP-Visio, a photoresin with reduced autofluorescence, we show a significant reduction in autofluorescence of the platform. Further, by integrating apertures onto the substrate with a gold coating, the influence of autofluorescence on imaging is almost completely mitigated. With this new platform, we demonstrate the ability to image a pair of epithelial cells as they are stretched up to 250% strain, allowing us to observe junction rupture and F-actin retraction while simultaneously recording the accumulation of over 800 kPa of stress in the junction. In conclusion, the platform and methodology presented here can potentially enable detailed investigation of the mechanics of and mechanotransduction in cell-cell junctions and improve the design of other TPP platforms in mechanobiology applications.

Autofluorescence↗
DOE OSTI2022

Two–Photon Polymerized Shape Memory Microfibers: A New Mechanical Characterization Method in Liquid

Two-photon polymerization (TPP) is widely used to create 3D micro- and nanoscale scaffolds for biological and mechanobiological studies, which often require the mechanical characterization of the TPP fabricated structures. To satisfy physiological requirements, most of the mechanical characterizations need to be conducted in liquid. However, previous characterizations of TPP fabricated structures are all conducted in air due to the limitation of conventional micro- and nanoscale mechanical testing methods. In this study, a new experimental method is reported for testing the mechanical properties of TPP-printed microfibers in liquid. The experiments show that the mechanical behaviors of the microfibers tested in liquid are significantly different from those tested in air. By controlling the TPP writing parameters, the mechanical properties of the microfibers can be tailored over a wide range to meet a variety of mechanobiology applications. In addition, it is found that, in water, the plasticly deformed microfibers can return to their predeformed shape after tensile strain is released. The shape recovery time is dependent on the size of microfibers. The experimental method represents a significant advancement in mechanical testing of TPP fabricated structures and may help release the full potential of TPP fabricated 3D tissue scaffolds for mechanobiological studies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Enabling a novel approach to a controlled fabrication of 1D crystalline nanowires on suspended microstructures of arbitrary geometries using two direct-writing technologies

Recent progresses in additive manufacturing have inspired new technologies, such as direct laser writing technique, based on two-photon polymerization (2 PP), which complements and further enriches the nanofabrication tools portfolio. Here, we combine 2 PP and our mask-free scanning probe assisted ‘direct-write patterning’ (DWP) method to allow for: a) the fabrication of micro-bridge structures with sub-micrometer resolution, b) selective synthesis of crystalline ZnO nanowires at predefined locations, respectively. This synergistic approach enables cantilever probe patterning of catalysts directly on suspended micro-bridges for in-situ CVD growth of nanoscale material, in a templated manner. The study reported here represents the first proof-of-concept experiments demonstrating versatile and scalable methodology, which can be applied and straightforwardly extended to grow a variety of other nanomaterials, in a controlled and selective fashion, on freestanding micro/nanoscale structures, whose size and geometry can be conveniently varied via templating of sacrificial 2 PP polymeric scaffolds. Furthermore, the demonstration of the possibility to integrate this new approach with the conventional lithography techniques provides a step forward to the development of the novel class of hybrid polymer-silicon-1D or -2D materials, and systems. The quality of the produced ZnO nanowire assemblies was assessed using several physical characterization methods.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Engineering Tunneling Selector to Achieve High Non-linearity for 1S1R Integration

Memristor devices have been extensively studied as one of the most promising technologies for next-generation non-volatile memory. However, for the memristor devices to have a real technological impact, they must be densely packed in a large crossbar array (CBA) exceeding Gigabytes in size. Devising a selector device that is CMOS compatible, 3D stackable, and has a high non-linearity (NL) and great endurance is a crucial enabling ingredient to reach this goal. Tunneling based selectors are very promising in these aspects, but the mediocre NL value limits their applications in large passive crossbar arrays. In this work, we demonstrated a trilayer tunneling selector based on the Ge/Pt/TaN 1+x /Ta 2 O 5 /TaN 1+x /Pd layers that could achieve a NL of 3 × 10 5 , which is the highest NL achieved using a tunnel selector so far. The record-high tunneling NL is partially attributed to the bottom electrode's ultra-smoothness (BE) induced by a Ge/Pt layer. We further demonstrated the feasibility of 1S1R (1-selector 1-resistor) integration by vertically integrating a Pd/Ta 2 O 5 /Ru based memristor on top of the proposed selector.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Characterization of the strain-rate–dependent mechanical response of single cell–cell junctions

Cell–cell junctions are essential components in multicellular structures and often experience strains of different magnitudes and rates. However, their mechanical behavior is currently underexplored due to the lack of techniques to quantitatively characterize junctional stress–strain relationships. Here we developed a polymeric microstructure to strain the mutual junction of a single cell pair while simultaneously recording the junction stress and observed previously unseen strain-rate–dependent junction responses. We showed that cytoskeleton growth could relax the stress buildup and prevent junction failure at low strain rates, while high strain rates led to synchronized junction failures at remarkably large strains (over 200%). We expect this platform and our biophysical understanding to form the foundation for the rate-dependent mechanics of cell–cell junctions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Permanently Magnetized Insulating Thin-Film Devices by Reduction

A reduction-based manufacturing process for creating technologically important multilayer structures from lattice-matched ferromagnetic insulators and ferromagnetic conductors is reported. The process is demonstrated by growing a permanently magnetized double-layer structure, consisting of lattice-matched conducting (Ni,Co) and insulating (Ni 0.4 Co 0.6 ) 3 O 3 layers, through a single deposition cycle. The orientation of the metal cation network is preserved after reduction. Close-packing displacements of Ni and Co take place in such a manner that the in-plane hexagonal arrangement is preserved. This is critical for ensuring high-quality interfaces joining the layers. At room temperature the hysteresis loop is centered. At low temperature the oxide layer becomes ferrimagnetically ordered, accompanied by a shift of the hysteresis loop along the magnetic field axis. The shift is assigned to exchange bias phenomenon. Biaxial compressive strain is responsible for the required ferrimagnetic ordering. Finally, spin valves and closely related magnetoresistance random access memory and spin-transfer-torque magnetic random access memory devices are addressed as potential applications.

42 ENGINEERING↗
DOE OSTI2019

Optically read Coriolis vibratory gyroscope based on a silicon tuning fork

In this work, we describe the design, fabrication, and characterization of purely mechanical miniature resonating structures that exhibit gyroscopic performance comparable to that of more complex microelectromechanical systems. Compared to previous implementations of Coriolis vibratory gyroscopes, the present approach has the key advantage of using excitation and probing that do not require any on-chip electronics or electrical contacts near the resonating structure. More specifically, our design relies on differential optical readout, each channel of which is similar to the 'optical lever' readout used in atomic force microscopy. The piezoelectrically actuated stage provides highly efficient excitation of millimeter-scale tuning fork structures that were fabricated using widely available high-throughput wafer-level silicon processing. In our experiments, reproducible responses to rotational rates as low as 1.8 × 10 3° h –1 were demonstrated using a benchtop prototype without any additional processing of the raw signal. The noise-equivalent rate, ΩNER, derived from the Allan deviation plot, was found to be <0.5° h –1 for a time of 10 3 s. Despite the relatively low Q factors (<10 4 ) of the tuning fork structures operating under ambient pressure and temperature conditions, the measured performance was not limited by thermomechanical noise. In fact, the performance demonstrated in this proof-of-principle study is approximately four orders of magnitude away from the fundamental limit.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Ionic Conductance through Graphene: Assessing Its Applicability as a Proton Selective Membrane

Inspired by recent reports on possible proton conductance through graphene, we have investigated the behavior of pristine graphene and defect engineered graphene membranes for ionic conductance and selectivity with the goal of evaluating a possibility of its application as a proton selective membrane. The averaged conductance for pristine chemical vapor deposited (CVD) graphene at pH1 is ~4 mS/cm 2 but varies strongly due to contributions from the unavoidable defects in our CVD graphene. From the variations in the conductance with electrolyte strength and pH, we can conclude that pristine graphene is fairly selective and the conductance is mainly due to protons. Furthermore, engineering of the defects with ion beam (He + , Ga + ) irradiation and plasma (N 2 and H 2 ) treatment showed improved areal conductance with high proton selectivity mostly for He-ion beam and H 2 plasma treatments, which agrees with primarily vacancy-free type of defects produced in these cases confirmed by Raman analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Room–Temperature Insulating Ferromagnetic (Ni,Co) 1+2 x Ti 1– x O 3 Thin Films

Insulating uniaxial room–temperature ferromagnets are a prerequisite for commonplace spin wave–based devices, the obstacle in contemporary ferromagnets being the coupling of ferromagnetism with large conductivity. It is shown that the uniaxial A 1 + 2x Ti 4+ 1 – x O 3 (ATO), A = Ni 2+ ,Co 2+ , and 0.6 < x ≤ 1, thin films are electrically insulating ferromagnets already at room temperature. Here, the octahedra network of the ATO and the corundum and ilmenite structures are the same yet different octahedra–filling proved to be a route to switch from the antiferromagnetic to ferromagnetic regime. Octahedra can continuously be filled up to x = 1, or vacated (–0.24 < x < 0) in the ATO structure. TiO–layers, which separate the ferromagnetic (Ni,Co)O–layers and intermediate the antiferromagnetic coupling between the ferromagnetic layers in the NiTiO 3 and CoTiO 3 ilmenites, can continuously be replaced by (Ni,Co)O–layers to convert the ATO–films to ferromagnetic insulator with abundant direct cation interactions.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Carbon nanospikes have better electrochemical properties than carbon nanotubes due to greater surface roughness and defect sites

Carbon nanomaterials are used to improve electrodes for neurotransmitter detection, but what properties are important for maximizing those effects? In this work, we compare a newer form of graphene, carbon nanospikes (CNSs), with carbon nanotubes (CNTs) grown on wires and carbon fibers (CFs). CNS electrodes have a short, dense, defect-filled surface that produces remarkable electrochemical properties, much better than CNTs or CFs. The CNS surface roughness is 5.5 times greater than glassy carbon, while CNTs enhance roughness only 1.8-fold. D/G ratios are higher for CNS electrodes than CNT electrodes, an indication of more defect sites. For cyclic voltammetry of dopamine and ferricyanide, CNSs have both higher currents and smaller ΔE p values than CNTs and CFs. CNS electrodes also have a very low resistance to charge transfer. With fast-scan cyclic voltammetry (FSCV), CNS electrodes have enhanced current density for dopamine and cationic neurotransmitters due to increased adsorption to edge plane sites. Furthermore, this study establishes that not all carbon nanomaterials are equally advantageous for dopamine electrochemistry, but that short, dense nanomaterials that add defect sites provide improved current and electron transfer. CNSs are simple to mass fabricate on a variety of substrates and thus could be a favorable material for neurotransmitter sensing.

36 MATERIALS SCIENCE↗
DOE OSTI2019

In Quest of a Ferromagnetic Insulator: Structure-Controlled Magnetism in Mg–Ti–O Thin Films

Ferromagnetic insulator thin films can convey information by spin waves, avoiding charge displacement and Eddy current losses. The sparsity of high-temperature insulating ferromagnetic materials hinders the development of spin-wave-based devices. Stoichiometric magnesium titanate, MgTiO 3 , has an electronic-energy-band structure in which all bands are either full or empty, being a paramagnetic insulator. The MgTiO 3 ilmenite consists of ordered octahedra and a cation network in which one-third of the octahedra are vacant, one-third host magnesium, and one-third titanium. By giving up these characteristics, a rich variety of different magnetic structures can be formed. Our experiments and electronic-energy-band-structure computations show that the magnetic and electric properties of Mg–Ti–O films can drastically be changed and controlled by Mg- and Ti-cation arrangement and abundancy in the octahedra. Insulating titanium- and semiconducting magnesium-rich films exhibited reversible magnetization up to elevated temperatures. The presence and origin of the insulating phase with reversible magnetization, assigned to ferromagnetic ordering, is not apparent. Here, the expectation, based on the well-established rules set by Goodenough and Kanamori, is paramagnetic or antiferromagnetic ordering. We show that ferro- and paramagnetic phases, possessing the same stoichiometry, can be obtained by merely rearranging the cations, thus allowing defect-free interfaces in multilayer structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Surface-Enhanced Raman Scattering (SERS) Studies of Disc-on-Pillar (DOP) Arrays: Contrasting Enhancement Factor with Analytical Performance

The use of nanomachining methods capable of reproducible construction of nano-arrayed devices have revolutionized the field of plasmonic sensing by the introduction of a diversity of rationally engineered designs. Significant strides have been made to fabricate plasmonic platforms with tailored interparticle gaps to improve their performance for surface-enhanced Raman scattering (SERS) applications. Over time, a dichotomy has emerged in the implementation of SERS for analytical applications, the construction of substrates, optimization of interparticle spacing as a means to optimize electromagnetic field enhancement at the localized surface plasmon level, and the substrate sensitivity over extended areas to achieve quantitative performance. Here, we assessed the enhancement factor of plasmonic Ag/SiO 2 /Si disc-on-pillar (DOP) arrays of variable pitch with its analytical performance for quantitative applications. Experimental data were compared with those from finite-difference time-domain (FDTD) simulations used in the optimization of the array dimensions. A self-assembled monolayer (SAM) of benzenethiol rendered highly reproducible signals (RSD ~4–10%) and SERS substrate enhancement factor (SSEF) values in the orders of 10 6 –10 8 for all pitches. Furthermore, spectra corresponding to rhodamine 6G (R6G) and 4-aminobenzoic acid demonstrated the advantages of using the more densely packed DOP arrays with a 160 nm pitch (gap= 40 nm) for quantitation in spite of the strongest SSEF was attained for a pitch of 520 nm corresponding to a 400 nm gap.

36 MATERIALS SCIENCE↗