Engineering topics

Lawrence A Hand

Publications and source records attributed to Lawrence A Hand.

4 records

NASA NTRS2024

The CapiSorb Visible System (CVS) Demonstrations on ISS

Falling liquid film amine sorbent reactors have been successfully employed to scrub CO 2 aboard submarines for decades. However, applying such proven methods aboard orbiting and coast spacecraft is significantly challenged by the nearly weightless environment, where liquid sprays and films do not fall, and vapor bubbles and gases do not rise. The Capillary Sorbent (CapiSorb) Visible System (CVS) is a technology demonstration experiment performed aboard the ISS April 18 – 21, 2023. The system establishes stable steady thin liquid film flows in Contactor (absorber) and Degasser (desorber/stripper) replacing the passive role of gravity with the combined passive roles of surface tension, wetting, and system geometry. A TOX-0 fructose ersatz liquid sorbent is employed enabling ‘transparent’ experiments performed and filmed by the crew safely in the open cabin of the ISS. Completed objectives include demonstrations of stable passive ‘massively’ parallel planar thin film capillary flows across atmospheric pressure Contactor and sealed heated Degasser. The impacts of varying flow rate, flow direction, heat input, viscosity, positive and negative Degasser pressures, condensate collection and return, fluid distribution, interfacial stability, and others are reported. At least 49 diagnostics are recorded for digitization and subsequent thermal-fluids model validation by a single HD video downlink during the nearly 22 hours of operations. An overview of the flight hardware including description of the components, diagnostics, crew procedures, flight operations, and summary of accomplishments is reported in Ref. 1. Further details of the diagnostics, tests performed, and data reduction is reported in Ref. 2. This report collects both1,2 into a single report adding methods of data digitization, reduction, and archive along with analyses and discussions of technology impacts.

microgravity↗

NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper describes the Dynamic Mode Decomposition (DMD) of the pressures on the scale model of the Space Launch System (SLS) Block 1 cargo vehicle with the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected in the Ascent Transient Aerodynamics Tests with the Unitary Plan Wind Tunnel 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD) of the data matrix. For the matrix of the uPSP measurements of the SLS ATAT, the number of rows is equal to the number of nodes in the grid of the scale model, and the number of columns is equal to the number of frames in the videos taken with 4 Phantom high-speed cameras. In this paper, it is verified that, for the time series with zero mean value, the DMD is equivalent to the decomposition with the Discrete Fourier Transform (DFT). Considering the uPSP is mainly used in the assessment of the unsteady, aerodynamic phenomena, the DMD of the uPSP measurements can be implemented in two steps: (1) subtract the mean value from the uPSP measurement on each of the grid nodes; (2) apply the Fast Fourier Transform (FFT) on the resulting zero-mean time series. The DMD of the uPSP measurements with FFT has two advantages: (1) the computational complexity of FFT is O(N*logN), where N is the length of the time series; (2) compared to the SVD-based DMD algorithm, the DMD with FFT can be easily implemented in parallel processing. A sample matrix of uPSP measurements, at the size of 341 grid nodes and 128 frames, is generated. Figures 1 and 2 show the eigenvalues and the ratios of the eigenvectors, respectively, of the sample matrix, without and with the mean value removed on each of the grid nodes, computed with the SVD-based DMD and the FFT. The figures demonstrate the equivalence of the SVD-based DMD and the decomposition with DFT/FFT for the time series with zero mean value. The results of DMD of the uPSP measurements of the SLS ATAT in September 2019 are presented in the paper. The DMD modes at different frequencies are shown, the aerodynamic phenomena (e.g. shockwave and vortex shedding) are demonstrated and the correlation of the DMD modes with the test configuration parameter (e.g., the Mach Number) is discussed. Figure 3 shows a software tool to visualize the DMD modes. The code to implement the algorithm described in this paper was written in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, and executed on the NASA Pleiades supercomputer. Funding for this research was provided by the NASA Aerosciences Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗

NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper discusses the Dynamic Mode Decomposition (DMD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected with four Phantom high-speed cameras at a constant sample frequency in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle with the Unitary Plan Wind Tunnel (UPWT) 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD). For the data with zero mean, the DMD is equivalent to the Discrete Fourier Transform (DFT). Since the uPSP is mainly used to determine the unsteady property of the aerodynamic flow, the DMD of the uPSP measurements is implemented in two steps: (1) subtract the mean value from the uPSP measurement; (2) apply the Fast Fourier Transform (FFT) on the resulting data with zero mean. The DMD of the uPSP measurements with FFT has two advantages: (1) the FFT algorithm is well known for its computational efficiency, therefore, compared to the SVD-based DMD algorithm, the DMD with FFT reduces the computation time; (2) the DMD with FFT can be easily implemented in parallel processing. The DMD outputs were generated with the execution in parallel of a code in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, on the NASA Pleiades supercomputer. In this paper, the results of DMD of the uPSP measurements in the tests of Mach sweep runs of the SLS ATAT are presented, and the effectiveness of the DMD of the uPSP measurements in the diagnosis of the unsteady, aerodynamic phenomena is demonstrated. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding for this research was provided by the NASA Aeroscience Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗

NASA NTRSDate not supplied

NASA’s Unsteady Pressure-Sensitive Paint Phase I Development Overview

Since 2019, a group out of NASA Ames Research Center(ARC)has been focused on implementing systematic updates to make unsteady pressure-sensitive paint (uPSP) a more viable capability for production wind tunnel testing. Focusing on the general categories of data acquisition, data transfer, data processing, and data visualization, the uPSP Development Team has made several improvements to increase data quality and innovate a more workable system that would provide valuable surface pressure data to customers. As a result of the COVID-19 pandemic and several initial demonstration tests prior to the formal start of the development effort, the decision was made to focus on launch vehicles as the test article. To-date this development has focused on implementation in the ARC Unitary Plan Wind Tunnel 11-by11-footTransonic Wind Tunnel due to the large optical access of the test section and that the NASA Advanced Supercomputer is located at ARC. This paper summarizes the project origins and the results of four years of development effort, which will all culminate in a final demonstration test in the first half of2024.

unsteady pressure-sensitive paint↗