Engineering topics
Lee, Chern-Jiin
Publications and source records attributed to Lee, Chern-Jiin.
Thermal design of the sample handling assembly in the sampling and caching subsystem on the Mars 2020 rover
The Mars 2020 Rover is scheduled to land on Mars on February 18, 2021. One of the primary mission objectives for the Mars 2020 Rover is to collect a set of Martian regolith samples for potential future return to Earth. Regolith and rock samples will be collected and placed into sample tubes using a coring drill, located at the end of a large Robotic Arm, on the outside of the rover. Filled sample tubes will be transferred from the outside of the Rover into the Adaptive Caching Assembly (ACA), located inside the Rover chassis, via the Bit Carousel. Once the filled sample tube is brought into the ACA, the Sample Handling Assembly (SHA) will transfer it to all of the internal processing stations of the ACA for volume assessment, sealing and finally drop-off on the Martian surface. The ACA is a volume within the rover chassis that is not temperature-controlled. Actuators inside the SHA and its End Effector (EE) must be warmed to above -55°C and -25°C, respectively, prior to use. This paper discusses the thermal design of the SHA that uses heaters and temperature sensors to warm up and maintain the temperature-sensitive arm components within temperature limits during operation. Thermal performance predictions for Mars surface operations are also presented.
Thermal Operability Improvements for the Mars 2020 Rover Surface Mission
The Mars 2020 Rover is scheduled to land on Mars on February 18, 2021. One of the primary mission objectives for the Mars 2020 Rover is to perform in-situ science and collect a set of Martian regolith samples for possible future return to Earth. In order to meet mission requirements, 20 samples must be collected, assessed, and sealed during the prime mission (1.5 Martian years, approximately 1000 Sols). This requires that the Mars 2020 Rover operate in a much more efficient and autonomous manner than its predecessor, the Mars Science Laboratory (MSL) Rover, Curiosity. The thermal designs of both Curiosity and the Mars 2020 Rover utilize warmup heaters to bring the actuators and cameras, located on the outside of the vehicle, up to their operating temperatures prior to use. These heaters consume energy during the mission. The Rover energy balance, between energy production and consumption, must be maintained in order to keep the mission moving safely forward. Increased efficiency in the way this warmup heater energy is allocated and used in the Mars 2020 Rover operations plan will result in more energy available for science and engineering activities. This paper discusses the improvements that were made in both hardware and software to improve the way the Mars 2020 Rover will operate thermally on Mars.
Thermal Performance of the Mars Science Laboratory Rover During Mars Surface Operations
On November 26, 2011, NASA launched a large (900 kg) rover as part of the Mars Science Laboratory (MSL) mission to Mars. Eight months later, on August 5, 2012, the MSL rover (Curiosity) successfully touched down on the surface of Mars. As of the writing of this paper, the rover had completed over 200 Sols of Mars surface operations in the Gale Crater landing site (4.5 degrees South latitude). This paper describes the thermal performance of the MSL Rover during the early part of its two Earth-0.year (670 Sols) prime surface mission. Curiosity landed in Gale Crater during early Spring (Solar longitude=151) in the Southern Hemisphere of Mars. This paper discusses the thermal performance of the rover from landing day (Sol 0) through Summer Solstice (Sol 197) and out to Sol 204. The rover surface thermal design performance was very close to pre-landing predictions. The very successful thermal design allowed a high level of operational power dissipation immediately after landing without overheating and required a minimal amount of survival heating. Early morning operations of cameras and actuators were aided by successful heating activities. MSL rover surface operations thermal experiences are discussed in this paper. Conclusions about the rover surface operations thermal performance are also presented.
Thermal Performance of the Mars Science Laboratory Rover During Mars Surface Operations
On November 26, 2011, NASA launched a large (900 kg) rover as part of the Mars Science Laboratory (MSL) mission to Mars. Eight months later, on August 5, 2012, the MSL rover (Curiosity) successfully touched down on the surface of Mars. As of the writing of this paper, the rover had completed over 200 Sols of Mars surface operations in the Gale Crater landing site (4.5 deg S latitude). This paper describes the thermal performance of the MSL Rover during the early part of its two Earth-0.year (670 Sols) prime surface mission. Curiosity landed in Gale Crater during early Spring (Ls=151) in the Southern Hemisphere of Mars. This paper discusses the thermal performance of the rover from landing day (Sol 0) through Summer Solstice (Sol 197) and out to Sol 204. The rover surface thermal design performance was very close to pre-landing predictions. The very successful thermal design allowed a high level of operational power dissipation immediately after landing without overheating and required a minimal amount of survival heating. Early morning operations of cameras and actuators were aided by successful heating activities. MSL rover surface operations thermal experiences are discussed in this paper. Conclusions about the rover surface operations thermal performance are also presented.
Mars Science Laboratory Rover Actuator Thermal Design
NASA will launch a 900 kg rover, part of the Mars Science Laboratory (MSL) mission, to Mars in October of 2011. The MSL rover is scheduled to land on Mars in August of 2012. The rover employs 31, electric-motor driven actuators to perform a variety of engineering and science functions including: mobility, camera pointing, telecommunications antenna steering, soil and rock sample acquisition and sample processing. This paper describes the MSL rover actuator thermal design. The actuators have stainless steel housings and planetary gearboxes that are lubricated with a "wet" lubricant. The lubricant viscosity increases with decreasing temperature. Warm-up heaters are required to bring the actuators up to temperature (above -55 C) prior to use in the cold wintertime environment of Mars (when ambient atmosphere temperatures are as cold as -113 C). Analytical thermal models of all 31 MSL actuators have been developed. The actuators have been analyzed and warm-up heaters have been designed to improve actuator performance in cold environments. Thermal hardware for the actuators has been specified, procured and installed. This paper presents actuator thermal analysis predicts, and describes the actuator thermal hardware and its operation. In addition, warm-up heater testing and thermal model correlation efforts for the Remote Sensing Mast (RSM) elevation actuator are discussed.
Mars Science Laboratory: Rover Actuator Thermal Design
This slide presentation reviews the actuator heating for the mars rover. This includes information on the history of actuator thermal design, design inputs, and the process for sizing heaters.
Thermal Design Validation of the Mars Scout Phoenix Payload
This slide presentation reviews the validation of the thermal design for the Mars Scout Phoenix Payload. It includes a description of the Phoenix Mission, the science objectives, the timeline, and the flight system and payloads that were on the lander. The initial responsibility for the development and validation the thermal design was with the developers. This process lacked overall system engineering, there was a difference of thermal expertise, and the number of institutions involved complicated the interactions. The revised approach for payload thermal design validation is described.
The Thermal Design Evolution of the Phoenix Robotic Arm
An adequate warm-up heater approach was developed using analysis & previous Mars surface experience. In the worst-cold environment, all the actuators were able to warm to their minimum operating temperature within the required time. In the worst-hot environment, the maximum continuous actuator power dissipation during normal operations was determined. A mechanical thermostat provides best means to cope with a failed-on wrist heater & to ease RA operations planning.