Engineering topics

Lee, Dong Un

Publications and source records attributed to Lee, Dong Un.

12 records

DOE OSTI2024

Modeling Planar Electrodes and Zero–Gap Membrane Electrode Assemblies for CO 2 Electrolysis

Multiphysics modeling enables probing of conditions inside a CO 2 electrolyzer that are difficult to measure, such as local concentrations and pH, as well as rapid testing of possible design changes. A one-dimensional model for a zero-gap membrane electrode assembly (MEA) CO 2 electrolyzer was developed with the assumption that catalyst layers interact with the membrane ionomer such that the ionomer affects the underlying kinetics. The kinetics for bicarbonate reacting to form hydrogen are fit using a planar electrode model for silver with an ionomer coating. The MEA model results are validated against experimental studies for current density and product selectivity. Flooding of the cathode is modeled using saturation curves, and results show that blocked pores in the microporous layer play a significant role in limiting the mass transport at high potentials (>2.8 V). Sensitivity studies showed that CO Faradaic efficiency can be increased by decreasing catalyst layer thickness and porosity, and decreasing KHCO 3 concentration.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2023

Controlling Mass Transport in Direct Carbon Dioxide Zero-Gap Electrolyzers via Cell Compression

The development of high-performance CO 2 electrolyzers is crucial for accelerating the sustainable production of fuels and chemicals integrated with renewable energy sources. Here, we introduce a methodology to actively control mass transport inside a realistic zero-gap membrane electrode assembly of a CO 2 electrolyzer by varying the gasket thickness, which consequently changes the cell compression. This allows control over the thickness and porosity of the gas diffusion electrodes, influencing the overall electrolyzer performance, as demonstrated using Ag-deposited electrodes. At low operating voltages (<2.9 V), both high- and low-compression electrolyzers exhibit similar faradaic efficiencies and partial current densities for CO formation. However, at high voltages, the low-compression electrolyzer with high electrode porosity demonstrates superior CO selectivity and activity with suppressed H 2 formation. These experimental results are validated by the computational membrane electrode assembly (MEA) model developed by using the measured in situ electrode thicknesses and electrode porosities. Additionally, liquid electrolyte saturation at the catalyst layer is found to play a dominant role in determining the mass transport, resulting in a decreased electrolyzer performance with low electrode porosity. Finally, the systematic investigation in this study improves the understanding of the transport dynamics in MEA-based devices and provides insights into optimizing device design parameters for industry-relevant CO 2 electrolysis.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2023

Mechanistic Insights into Aldehyde Production from Electrochemical CO 2 Reduction on CuAg Alloy via Operando X-ray Measurements

CO 2 electrolysis converts the greenhouse gas CO 2 into valuable fuels and chemicals, such as carbon monoxide, ethylene, ethanol, etc. Currently, Cu is the only known monometallic catalyst capable of producing multicarbon products from electrochemical CO 2 reduction reaction (eCO2RR), while the poor selectivity limits its further use. It has been found that introducing Ag atoms into the Cu lattice can modulate product preference. However, the synergistic effects between Cu and Ag, and thus, the catalytic performance, are strongly influenced by catalyst morphology, electrolyzer configuration, reaction conditions, etc. Operando measurements can provide explicit information on the catalyst dynamic variation during the reaction, but their operation and analysis are challenging. Herein, we prepared CuAg multiphase alloy catalysts by magnetron sputtering, which allowed for investigating the intrinsic interaction between Cu and Ag. eCO2RR performance exhibited an improved selectivity toward carbonyls at the expense of hydrogen and hydrocarbons. The partially alloyed Cu and Ag phases were confirmed by operando X-ray diffraction. By means of combining operando X-ray measurements and density functional theory (DFT) calculations, the preferred carbonyl production is attributed to the reduced electron density and compressive strain of Cu due to Ag incorporation, which leads to a deeper d-band center and therefore weakened intermediate adsorption and oxophilicity. In conclusion, this work provides evidence of the intrinsic structural and electronic interaction between Cu and Ag during eCO2RR. The obtained information will facilitate the design of bi/multi-phase metallic or alloy electrocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Bridging knowledge gaps in liquid- and vapor-fed CO 2 electrolysis through active electrode area

Increased use of gas diffusion electrodes for CO 2 electroreduction widens the experimental phase space that was previously inaccessible using foil electrodes, raising fundamental questions over the impacts of key variables that translate between liquid- and vapor-fed CO 2 electrolysis systems. This work focuses on studying the interplay of current-potential profiles and electrochemically active surface area (ECSA) by implementing a Cu nanoflower catalyst morphology. The results show decreased overpotentials as much as 460 and 174 mV for foil and gas diffusion electrodes, respectively, while maintaining or improving multi-carbon product current density. Furthermore, these overpotential shifts and product activities normalized by ECSA lead to current-potential relationships akin to those of the Tafel description, which are found through a continuum model to be useful for describing the roughness dependence for both liquid- and vapor-fed systems. This analysis establishes a holistic approach for establishing catalyst design criteria to improve materials development for CO 2 .

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Origins of wear-induced tungsten corrosion defects in semiconductor manufacturing during tungsten chemical mechanical polishing

During chemical mechanical polishing (CMP) process optimization, a unique corrosion defect was identified in the tungsten (W) contact plugs, which were investigated to develop practical solutions to improve CMP mass productivity. The corrosion defect occurred in the absence of external incident energy and was observed to occur only at the W plugs connected to the P + /n-well close to the wafer edge. To examine the root cause of the corrosion, a series of experiments was carried out at each W CMP step, using in-line defect inspection. Additional experiments were conducted using on-line inductively coupled plasma mass spectrometry (ICP-MS) to understand pH- and potential-dependent electrochemical dissolution behaviors of W. Experimentally, W corrosion was confirmed to be exacerbated if the surface oxide of the W plugs is removed by the deionized water (DIW) rinsing step under wafer pressurization, then exposed to DIW and alkaline cleaning solution. Although the DIW rinsing step is commonly performed to clean polishing pads right after the main polishing, a small amount of applied pressure (0.5 psi) without slurry supply can lead to corrosion defects. Finally, this wear-induced corrosion of the W plugs can be prevented by removing the applied pressure during the post DIW rinsing step of W CMP.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Vapor–Fed Electrolyzers for Carbon Dioxide Reduction Using Tandem Electrocatalysts: Cuprous Oxide Coupled with Nickel–Coordinated Nitrogen–Doped Carbon

We report ethylene is particularly attractive due to its major importance as a feedstock for various applications including the polymer industry. As such, catalyst and electrolyzer developments are crucial to achieve industrially relevant ethylene production and efficiency levels. In this work, a tandem electrocatalyst composed of copper nanocubes and nickel-coordinated nitrogen-doped carbon (NiNC) is presented, which is integrated into gas diffusion electrodes (GDEs) for direct conversion of vapor-fed CO 2 into ethylene. Evaluation of tandem GDEs in the vapor-fed flow electrolyzer shows significantly increased ethylene selectivity in terms of faradaic efficiency and C 2 H 4 /CO ratio compared to a non-tandem copper GDE. The enhancements are attributed to the increased local CO availability near the copper surface via effective CO 2 to CO conversion on neighboring NiNC. The experimental results are validated by 3D resolved continuum simulations, which show increased flux of higher-order prod-ucts with the added CO flux from NiNC. The practical viability of Cu/NiNC catalyst is further evaluated in a membrane electrode assembly electrolyzer, achieving 40% FE toward ethylene at 150 mA cm -2 and 3.2 V. These find-ings highlight the high selectivity and formation rate of ethylene achieved by successful device integration of the Cu/NiNC catalyst, demonstrating the potential for implementation in large-scale sustainable CO 2 electrolyzers.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Designing a Zn–Ag Catalyst Matrix and Electrolyzer System for CO 2 Conversion to CO and Beyond

CO 2 emissions can be transformed into high-added-value commodities through CO 2 electrocatalysis; however, efficient low-cost electrocatalysts are needed for global scale-up. Inspired by other emerging technologies, the authors report the development of a gas diffusion electrode containing highly dispersed Ag sites in a low-cost Zn matrix. Here, this catalyst shows unprecedented Ag mass activity for CO production: –614 mA cm –2 at 0.17 mg of Ag. Subsequent electrolyte engineering demonstrates that halide anions can further improve stability and activity of the Zn–Ag catalyst, outperforming pure Ag and Au. Membrane electrode assemblies are constructed and coupled to a microbial process that converts the CO to acetate and ethanol. Combined, these concepts present pathways to design catalysts and systems for CO 2 conversion toward sought-after products.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Improving intrinsic oxygen reduction activity and stability: Atomic layer deposition preparation of platinum-titanium alloy catalysts

Improved activity and stability Pt-based catalysts for the oxygen reduction reaction (ORR) are needed to perpetuate the deployment of polymer electrolyte fuel cells (PEFCs) in the transportation sector. In this study, we use atomic layer deposition of TiO 2 and Pt coupled with thermal reductive annealing to prepare Pt 3 Ti electrocatalysts. The atomic level synthetic control resulted in Pt 3 Ti nanoparticles with high ORR performance, including a mass activity of 1.84 A/mg Pt and excellent electrochemical stability. The Pt 3 Ti nanoparticles show excellent specific activity — 5.3-fold higher than commercial Pt/C and 3-fold higher than polycrystalline Pt, exceeding the performance of any PtTi catalysts reported to date. Combined experimental and computational efforts indicate that Pt enrichment on the Pt 3 Ti enhances the activity, and the intrinsic stability of the Pt 3 Ti phase provides durability. Subsequently, this knowledge, along with the facile fabrication of alloys by atomic layer deposition, can be leveraged to designed improved performance catalysts.

25 ENERGY STORAGE↗

DOE OSTI2021

Electrolyte-Guided Design of Electroreductive CO Coupling on Copper Surfaces

Engineering the interfacial distribution of electrolytic ions can aid in modulating the electrocatalyst performance and efficiency. Using a hybrid quantum-classical modeling approach, we describe how predictive tuning of the solution microenvironment on copper can enhance the efficiency of CO 2 reduction (CO 2 R) to C 2 products. We elucidate how competing electrolyte constituents in mixed electrolyte solutions stimulate restructuring of the electrochemical double layer (EDL) and stabilize the OCCO* dimer (* denotes surface adsorbed), with predictions validated in flow reactors using copper gas diffusion electrodes (Cu-GDEs). Furthermore, our findings highlight how molecular-scale electrolyte engineering with informed models of the EDL can be leveraged to tailor CO 2 R activity and selectivity toward C 2 products.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Direct Integration of Strained-Pt Catalysts into Proton-Exchange-Membrane Fuel Cells with Atomic Layer Deposition

The design and fabrication of lattice-strained platinum catalysts achieved by removing a soluble core from a platinum shell synthesized via atomic layer deposition, is reported. The remarkable catalytic performance for the oxygen reduction reaction (ORR), measured in both half-cell and full-cell configurations, is attributed to the observed lattice strain. By further optimizing the nanoparticle geometry and ionomer/carbon interactions, mass activity close to 0.8 A mg Pt -1 @0.9 V iR-free is achievable in the membrane electrode assembly. Nevertheless, active catalysts with high ORR activity do not necessarily lead to high performance in the high-current-density (HCD) region. More attention shall be directed toward HCD performance for enabling high-power-density hydrogen fuel cells.

25 ENERGY STORAGE↗

DOE OSTI2021

Advanced manufacturing for electrosynthesis of fuels and chemicals from CO 2

Advanced manufacturing (AM) represents an appealing approach for creating novel electrochemical systems for chemicals synthesis. In this work, we demonstrate AM for rapid development and testing for improved performance for the carbon dioxide reduction reaction across an evolution of vapor-fed reactor designs. In our final design, we observe activation- and mixed-control regimes for a variety of operating conditions via inlet CO 2 flow rate and electrochemical potential. Furthermore, we define a dimensionless number (Da) to identify mass transport regimes by exploring the impact of hypothesized underlying mass transport mechanisms, including consumption of CO 2 via OH - , increased local temperatures, and partial penetration of electrolyte into gas diffusion layer. The accelerated pace of reactor design and development led to high geometric current densities (500 mA cm -2 ), heightened selectivity (85.5% FE C 2+ products), and increased carbon dioxide conversion (16.6%) and cathodic energy efficiency (49.6% CO 2 R). Using AM vapor-fed reactors, we attain high ethylene (3.67%) and record ethanol (3.66%) yields compared to the literature. Finally, this work underscores the promise of AM for accelerating reactor design, understanding of governing phenomena, and improving the performance of catalytic systems.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Understanding the Origin of Highly Selective CO 2 Electroreduction to CO on Ni,N‐doped Carbon Catalysts

Abstract Ni,N‐doped carbon catalysts have shown promising catalytic performance for CO 2 electroreduction (CO 2 R) to CO; this activity has often been attributed to the presence of nitrogen‐coordinated, single Ni atom active sites. However, experimentally confirming Ni−N bonding and correlating CO 2 reduction (CO 2 R) activity to these species has remained a fundamental challenge. We synthesized polyacrylonitrile‐derived Ni,N‐doped carbon electrocatalysts (Ni‐PACN) with a range of pyrolysis temperatures and Ni loadings and correlated their electrochemical activity with extensive physiochemical characterization to rigorously address the origin of activity in these materials. We found that the CO 2 R to CO partial current density increased with increased Ni content before plateauing at 2 wt % which suggests a dispersed Ni active site. These dispersed active sites were investigated by hard and soft X‐ray spectroscopy, which revealed that pyrrolic nitrogen ligands selectively bind Ni atoms in a distorted square‐planar geometry that strongly resembles the active sites of molecular metal–porphyrin catalysts.

Koshy, David M.↗