Engineering topics

Lee, F. C.

Publications and source records attributed to Lee, F. C..

At least 37 records · Page 2

NASA NTRS1984

Resonant power processors. II - Methods of control

The nature of resonant converter control is discussed. Employing the state-portrait, different control methods for series resonant converter are identified and their performance evaluated based on their stability, response to control and load changes and range of operation. A new control method, optimal-trajectory control, is proposed which, by utilizing the state trajectories as control laws, continuously monitors the energy level of the resonant tank. The method is shown to have superior control properties especially under transient operation.

Oruganti, R.↗

NASA NTRS1984

A fast time domain digital simulation technique for power converters - Application to a buck converter with feedforward compensation

Small signal analysis was performed earlier to demonstrate the marked improvement of dynamic properties and stability margins of a switching regulator employing a novel feedforward input filter compensation scheme. A large signal nonlinear recurrent time domain model is presented for the converter to analyse the transient response due to a step input change with and without the presence of the proposed feedforward loop. The results are verified with experimental data.

Kelkar, S. S.↗

NASA NTRS1984

Input filter compensation for switching regulators

Problems caused by input filter interaction and conventional input filter design techniques are discussed. The concept of feedforward control is modeled with an input filter and a buck regulator. Experimental measurement and comparison to the analytical predictions is carried out. Transient response and the use of a feedforward loop to stabilize the regulator system is described. Other possible applications for feedforward control are included.

Lee, F. C.↗

NASA NTRS1983

Input filter compensation for switching regulators

A novel input filter compensation scheme for a buck regulator that eliminates the interaction between the input filter output impedance and the regulator control loop is presented. The scheme is implemented using a feedforward loop that senses the input filter state variables and uses this information to modulate the duty cycle signal. The feedforward design process presented is seen to be straightforward and the feedforward easy to implement. Extensive experimental data supported by analytical results show that significant performance improvement is achieved with the use of feedforward in the following performance categories: loop stability, audiosusceptibility, output impedance and transient response. The use of feedforward results in isolating the switching regulator from its power source thus eliminating all interaction between the regulator and equipment upstream. In addition the use of feedforward removes some of the input filter design constraints and makes the input filter design process simpler thus making it possible to optimize the input filter. The concept of feedforward compensation can also be extended to other types of switching regulators.

Kelkar, S. S.↗

NASA NTRS1983

A novel feedforward compensation canceling input filter-regulator interaction

The interaction between the input and the control loop of switching regulators often results in deterimental effects, such as loop instability, degradation of transient response, and audiosusceptibility, etc. The concept of pole-zero cancelation is employed to mitigate some of these detrimental effects and is implemented using a novel feedforward loop, in addition to existing feedback loops of a buck regulator. Experimental results are presented which show excellent correlation with theory.

Kelkar, S. S.↗

NASA NTRS1983

Extensions of the discrete-average models for converter power stages

An improved power converter model is developed by combining the average and discrete modeling techniques. The parameter determination of the proposed discrete-average model is shown to be dependent on the type of duty cycle control law, and the accuracy of the model is shown to depend on the nature of the error processor used in the feedback loop.

Shortt, D. J.↗

NASA NTRS1983

Stability analysis of a buck regulator employing input filter compensation

The interaction between the input filter and the regulator often causes serious degradation of performance. The reduction in loop gain due to input filter interaction can result in system instability. An exact stability analysis of the buck regulator system is presented. The input filter parameter values are varied and system instability is predicted for the case without feedforward. The eigenvalues of the system can be brought back into the unit circle and the system thus stabilized with the addition of the feedforward loop. Measurements made for the cases with and without feedforward confirm the analytical prediction.

Kelkar, S. S.↗

NASA NTRS1982

Analysis and design of a standardized control module for switching regulators

Three basic switching regulators: buck, boost, and buck/boost, employing a multiloop standardized control module (SCM) were characterized by a common small signal block diagram. Employing the unified model, regulator performances such as stability, audiosusceptibility, output impedance, and step load transient are analyzed and key performance indexes are expressed in simple analytical forms. More importantly, the performance characteristics of all three regulators are shown to enjoy common properties due to the unique SCM control scheme which nullifies the positive zero and provides adaptive compensation to the moving poles of the boost and buck/boost converters. This allows a simple unified design procedure to be devised for selecting the key SCM control parameters for an arbitrarily given power stage configuration and parameter values, such that all regulator performance specifications can be met and optimized concurrently in a single design attempt.

Lee, F. C.↗

NASA NTRS1982

A novel input filter compensation scheme for switching regulators

A novel input-filter compensation scheme is proposed which uses feedforward loops to cancel the effects of peaking of the output impedance of the input filter, such that the converter is immune from performance degradation due to loop gain reduction. The scheme makes it possible to concurrently implement a high-performance converter and an effective input filter design with minimum weight and loss. A buck regulator with continuous current conduction is used as an example, and an analysis followed by a design procedure for the feedforward loops is presented.

Kelkar, S. S.↗

NASA NTRS1982

An improved switching converter model using discrete and average techniques

The nonlinear modeling and analysis of dc-dc converters has been done by averaging and discrete-sampling techniques. The averaging technique is simple, but inaccurate as the modulation frequencies approach the theoretical limit of one-half the switching frequency. The discrete technique is accurate even at high frequencies, but is very complex and cumbersome. An improved model is developed by combining the aforementioned techniques. This new model is easy to implement in circuit and state variable forms and is accurate to the theoretical limit.

Shortt, D. J.↗

NASA NTRS1982

Input filter compensation for switching regulators

The problems caused by the interaction between the input filter, output filter, and the control loop are discussed. The input filter design is made more complicated because of the need to avoid performance degradation and also stay within the weight and loss limitations. Conventional input filter design techniques are then dicussed. The concept of pole zero cancellation is reviewed; this concept is the basis for an approach to control the peaking of the output impedance of the input filter and thus mitigate some of the problems caused by the input filter. The proposed approach for control of the peaking of the output impedance of the input filter is to use a feedforward loop working in conjunction with feedback loops, thus forming a total state control scheme. The design of the feedforward loop for a buck regulator is described. A possible implementation of the feedforward loop design is suggested.

Lee, F. C.↗

NASA NTRS1981

Power system design optimization using Lagrange multiplier techniques

An optimization technique using the Lagrange Multiplier Method is proposed to facilitate design of switching power converter systems. The essence of the optimization is to identify the optimal battery voltage level and switching frequency along with the detailed converter design so that the total system weight including the battery and the packaged converter is minimized, and concurrently all specified power circuit performances are satisfied.

Yu, Y.↗

NASA NTRS1981

A new approach to the minimum weight/loss design of switching power converters

A new technique using the mathematical nonlinear programming ALAG is proposed to facilitate design optimizations of switching power converters. This computer-aided approach provides a minimum weight (or loss) design down to the details of component level and concurrently satisfies all related power-circuit performance requirements. It also provides such design insights as tradeoffs between power loss and system weight as the switching frequency is increased.

Lee, F. C.↗

NASA NTRS1981

Investigations of stability and dynamic performances of switching regulators employing current-injected control

The stability and dynamic performances of a buck/boost regulator employing a current-injected control are examined. Small-signal models for the power state, the multi-loop error processor and the duty-cycle pulse-modulator are developed. The error-processor model which incorporates the current-injected loop, the dc loop and the compensation network permits evaluation of the effects of each individual control loop and their combined efforts toward shaping the performance characteristics of the closed-loop system. Comparisons are made between this modeling approach and earlier approaches. Some important yet subtle dissimilarities are discussed. This model predicts the constant-frequency 50 percent duty-cycle instability which is inherent to the current-injected control.

Lee, F. C.↗

NASA NTRS1981

Nonlinear program based optimization of boost and buck-boost converter designs

The facility of an Augmented Lagrangian (ALAG) multiplier based nonlinear programming technique is demonstrated for minimum-weight design optimizations of boost and buck-boost power converters. Certain important features of ALAG are presented in the framework of a comprehensive design example for buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight and loss profiles of various semiconductor components and magnetics as a function of the switching frequency.

Rahman, S.↗

NASA NTRS1980

Modeling and Analysis of Power Processing Systems (MAPPS). Volume 1: Technical report

Computer aided design and analysis techniques were applied to power processing equipment. Topics covered include: (1) discrete time domain analysis of switching regulators for performance analysis; (2) design optimization of power converters using augmented Lagrangian penalty function technique; (3) investigation of current-injected multiloop controlled switching regulators; and (4) application of optimization for Navy VSTOL energy power system. The generation of the mathematical models and the development and application of computer aided design techniques to solve the different mathematical models are discussed. Recommendations are made for future work that would enhance the application of the computer aided design techniques for power processing systems.

Lee, F. C.↗

NASA NTRS1980

Modeling and Analysis of Power Processing Systems (MAPPS). Volume 2: Appendices

The computer programs and derivations generated in support of the modeling and design optimization program are presented. Programs for the buck regulator, boost regulator, and buck-boost regulator are described. The computer program for the design optimization calculations is presented. Constraints for the boost and buck-boost converter were derived. Derivations of state-space equations and transfer functions are presented. Computer lists for the converters are presented, and the input parameters justified.

Lee, F. C.↗

NASA NTRS1980

Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

Lee, F. C.↗