Engineering topics

Lee, Jinho

Publications and source records attributed to Lee, Jinho.

6 records

NASA NTRS2010

The Mothball, Sustainment, and Proposed Reactivation of the Hypersonic Tunnel Facility (HTF) at NASA Glenn Research Center Plum Brook Station

The Hypersonic Tunnel Facility (HTF) located at the NASA Glenn Research Center s Plum Brook Station in Sandusky, Ohio, is the nation s only large-scale, non-vitiated, hypersonic propulsion test facility. The HTF, with its 4-story graphite induction heater, is capable of duplicating Mach 5, 6, and 7 flight conditions. This unique propulsion system test facility has experienced several standby and reactivation cycles. The intent of the paper is to overview the HTF capabilities to the propulsion community, present the current status of HTF, and share the lessons learned from putting a large-scale facility into mothball status for a later restart

Thomas, Scott R.↗

NASA NTRS2007

TBCC Inlet Experiments and Analysis

A research plan is being implemented at NASA to investigate inlet mode transition for turbine-based combined-cycle (TBCC) propulsion for the hypersonic community. Unresolved issues have remained on how to design an inlet system to supply both a turbine engine and a ram/scramjet flowpath that operate with both high performance and stability. The current plan is aimed at characterizing the design, performance and operability of TBCC inlets through a series of experiments and analyses. A TBCC inlet has been designed that is capable of high performance (near MIL-E-5008B recovery) with smooth transitioning characteristics. Traditional design techniques were used in an innovative approach to balance the aerodynamic and mechanical constraints to create a new TBCC inlet concept. The inlet was designed for top-end Mach 7 scramjet speeds with an over/under turbine that becomes cocooned beyond its Mach 4 peak design point. Conceptually, this propulsion system was picked to meet the needs of the first stage of a two-stage to orbit vehicle. A series of increasing fidelity CFD-based tools are being used throughout this effort. A small-scale inlet experiment is on-going in the GRC 1'x1' Supersonic Wind Tunnel (SWT). Initial results from both the CFD analyses and test are discussed showing that high performance and smooth mode transitions are possible. The effort validates the design and is contributing to a large-scale inlet/propulsion test being planned for the GRC 10' x10' SWT. This large-scale effort provide the basis for a Combined Cycle Engine Testbed, (CCET), that will be able to address integrated propulsion system and controls objectives.

Saunders, Dave↗

NASA NTRS1995

Surface modeling and grid generation for aeropropulsion CFD

The efforts in geometry modeling and grid generation at the NASA Lewis Research Center, as applied to the computational fluid dynamic (CFD) analysis of aeropropulsion systems, are presented. The efforts are mainly characterized by a focus on the analysis of components of an aeropropulsion system, which involve turbulent viscous flow with heat transfer and chemistry. Thus, this discussion will follow that characterization and will sequence through the components of typical propulsion systems consisting of inlets, compressors, combustors, turbines, and nozzles. For each component, some applications of CFD analysis will be presented to show how CFD is used to compute the desired performance information, how geometry modeling and grid generation are performed, and what issues have developed related to geometry modeling and grid generation. The discussion will illustrate the following needs related to geometry modeling and grid generation as observed in aeropropulsion analysis: (1) accurate and efficient resolution of turbulent viscous and chemically-reacting flowfields; (2) easy-to-use interfaces with CAD data for automated grid generation about complex geometries; and (3) automated batch grid generation software for use with design and optimization software.

Choo, Yung K.↗

NASA NTRS1993

Prediction of gas-liquid two-phase flow regime in microgravity

An attempt is made to predict gas-liquid two-phase flow regime in a pipe in a microgravity environment through scaling analysis based on dominant physical mechanisms. Simple inlet geometry is adopted in the analysis to see the effect of inlet configuration on flow regime transitions. Comparison of the prediction with the existing experimental data shows good agreement, though more work is required to better define some physical parameters. The analysis clarifies much of the physics involved in this problem and can be applied to other configurations.

Lee, Jinho↗

NASA NTRS1993

Scaling analysis of gas-liquid two-phase flow pattern in microgravity

A scaling analysis of gas-liquid two-phase flow pattern in microgravity, based on the dominant physical mechanism, was carried out with the goal of predicting the gas-liquid two-phase flow regime in a pipe under conditions of microgravity. The results demonstrated the effect of inlet geometry on the flow regime transition. A comparison of the predictions with existing experimental data showed good agreement.

Lee, Jinho↗

NASA NTRS1991

Studies of aerothermal loads generated in regions of shock/shock interaction in hypersonic flow

Experimental studies were conducted to examine the aerothermal characteristics of shock/shock/boundary layer interaction regions generated by single and multiple incident shocks. The presented experimental studies were conducted over a Mach number range from 6 to 19 for a range of Reynolds numbers to obtain both laminar and turbulent interaction regions. Detailed heat transfer and pressure measurements were made for a range of interaction types and incident shock strengths over a transverse cylinder, with emphasis on the 3 and 4 type interaction regions. The measurements were compared with the simple Edney, Keyes, and Hains models for a range of interaction configurations and freestream conditions. The complex flowfields and aerothermal loads generated by multiple-shock impingement, while not generating as large peak loads, provide important test cases for code prediction. The detailed heat transfer and pressure measurements proved a good basis for evaluating the accuracy of simple prediction methods and detailed numerical solutions for laminar and transitional regions or shock/shock interactions.

Holden, Michael S.↗