Engineering topics
Lee, Kyungjun
Publications and source records attributed to Lee, Kyungjun.
Role of surface wetting on tribological behavior for laser nanotextured steel using ionic liquid lubricants
Here, this research evaluates the effect of surface wettability on the tribological performance through ball-on-flat tribology testing. The substrate material, M2 tool steel, is laser processed and then functionalized with fluorocarbon and nitrile chemistry to achieve distinct oleophobicity and oleophilicity, respectively, but with a similar nanoscale surface texture. The baseline lubricant is poly-alpha-olefin (PAO) oil, and ionic liquids (ILs) are used as additives for this study. The interaction between the nanoscale textured steel surface and ionic liquid-based oils is investigated. A set of reciprocating wear tests are performed to investigate the tribological behavior of the tribo-system consisting of the surface-engineered, flat M2 tool steel specimen and a standard, surface-polished steel ball. Results show that the oleophobic flat surface results in a lower friction, while the oleophilic surface modification leads to a better wear protection to the flat surface. Ammonium-based IL provides the highest friction reduction, while the phosphonium-based ILs provide an improved wear protection.
Investigation of Biomass Fouling on Screw Feeder in Preconversion of Pyrolysis
Biomass is a source of renewable energy and can undergo thermochemical processes to be converted into gaseous and liquid fuels. Thermal decomposition-induced biomass fouling on the screw feeder is a major challenge in preconversion of pyrolysis, leading to plugging of the feed line. Here, this work intends to gain fundamental understanding of the biomass fouling phenomena across the heat gradient on the screw feeder via a combination of materials characterization and thermal simulation. An actual screw feeder that failed because of biomass fouling was examined to reveal the deposit’s morphology, composition, and mechanical properties. Thermal simulations were developed for both the screw feeder and the wood particles being transported using a combined analytical and numerical approach. The simulated temperature profiles correlated well with the deposit observations, based on which potential mitigations were proposed from both the operation and screw design perspectives and supported by preliminary experimental validation.
Wear Mechanism Analysis of a New Rotary Shear Biomass Comminution System
A new biomass comminution system, Crumbler rotary shear, was developed to process fuel-grade biomass. The rotary shear is more efficient than the traditional hammer mill in comminuting high-moisture biomass and producing more uniform particles with minimal fines. However, the milling unit experiences significant wear in processing dirty woodchips. This study investigated the wear mechanisms of the rotary shear system based on analysis of the minerals carried by woodchips and characterization of actual worn components. Abrasive wear was found to be the dominant effect, and localized adhesive wear (material transfer), microfracture (chipping), and plastic deformation were additional effects. Connections have been made between the wear progression of key cutting components and the particle size change of biomass extrinsic minerals. On the basis of the wear mechanism understanding, mitigations based on advanced tool materials and optimized tool geometric designs are being developed for improving the tool life and cutting efficiency.
Corrosion and Chemical Characterization of Bio-Oils from Biomass with Varying Ash and Moisture Contents
As part of the Feedstock Conversion Interface Consortium four samples of pine chips (all combinations of low and high moisture and ash content) were collected and processed for fast pyrolysis. The prepared biomass samples were liquefied at the National Renewable Energy Laboratory (NREL) using the fast pyrolysis process. Following some characterization of the bio-oils at NREL, the bio-oils were shipped to Oak Ridge National Laboratory (ORNL) for corrosion testing and further characterization.The content and composition of ash in each bio-oil was determined. Corrosion testing consisted of exposing selected metallic and elastomer samples for 1000 hr at 50°C and for longer times at room temperature as well as electrochemical impedance spectroscopy measurements to assess relative corrosivity of the bio-oils. Chemical characterization was conducted to identify the corrosive component of the bio-oils as well as to define the chemical differences among the oils. It was hypothesized that there could be a catalytic effect from the higher ash content in two of the biomass sources. Results of these characterization and corrosion studies will be reported.
Material Characterization-Based Wear Mechanism Investigation for Biomass Hammer Mills
Biomass, as harvested, is composed of inorganic compounds both intrinsically and extrinsically and can be abrasive. The present study investigates the wear modes and mechanisms of two types of blades of hammer mills used in biomass size reduction (impacting the particle size and distribution) and densification (impacting the size, shape, and density). The dominant wear modes for the stage 1 steel blades are determined to be erosive and polishing wear. For the stage 2 blades with a carbide weld overlay, the main wear mechanisms are erosion and fracture. Partial replacement of Co by Fe in the outer layer of the carbide grits, likely induced by diffusion during high-temperature welding, has been correlated to the observed microcracking. Finally, the microcracking is believed to weaken the grit strength and fracture toughness to make the overlay prone to fracture and erosion due to repetitive contact with the inorganic contents in chopping biomass.
Composition-Preserving Extraction and Characterization of Biomass Extrinsic and Intrinsic Inorganic Compounds
The inorganic content of biomass impairs size reduction tool life and the conversion process. Conventional ash extraction relies on furnace combustion that inevitably alters the inorganic compounds due to oxidation and decomposition. This study developed composition-preserving methods for extracting and analyzing extrinsic and intrinsic inorganic compounds. Comprehensive characterization was carried out on selected biomass feedstocks, including corn stover, pine residue, and pine anatomical fractions, to reveal their inorganic species and morphology. The extrinsic inorganic compounds were found to be dominated by quartz, along with other minor minerals, such as albite, microcline, and gehlenite, and have particle sizes ranging from tens to hundreds of micrometers. Among the pine anatomical fractions, the needles contain the highest intrinsic silicon content while the bark trapped the most extrinsic minerals. By correlation of the total ash and extrinsic inorganic contents to the wear behavior, both the extrinsic and intrinsic inorganic compounds were concluded to have made significant contributions to the wear process. Finally, the results here validated a new approach to characterize inorganic compounds in biomass and provided fundamental insights for their potential impact on preprocessing tool wear.