Search NASA⌕ Search

Engineering topics

Lee, Peter J.

Publications and source records attributed to Lee, Peter J..

At least 19 records

Influence of Nb alloying on Nb recrystallization and the upper critical field of Nb 3 ⁢Sn

Nb 3 Sn conductors are important candidates for high-field magnets for particle accelerators, and they continue to be widely used for many laboratory and NMR magnets. However, the critical current density, J c , of present Nb 3 Sn conductors declines swiftly above 12-15 T. State-of-the-art Ta- and Ti-doped strands exhibit upper critical field, H c2 , values of ~ 24-26.5 T (4.2 K) and do not reach the FCC target J c , which serves as the present stretch target for Nb 3 Sn development. As recently demonstrated, to meet this goal requires enhanced vortex pinning but an independent and supplementary approach is to significantly enhance H c2 . In this study, we have arc-melted multiple Nb alloys with added Hf, Zr, Ta and Ti and drawn them successfully into monofilament wires to investigate the possibilities of H c2 enhancement through alloying. H c2 (T) was measured for all samples in fields up to 16 T and some up to 31 T. We have found that all alloys show good agreement with the standard Werthamer, Helfand, and Hohenberg (WHH) fitting procedure without the need to adjust the paramagnetic limitation parameter (α) and spin-orbit scattering parameter (λ so ). The evaluation of dH c2 /dT near T c , which is proportional to the electronic specific heat coefficient γ and the normal state resistivity ρn, allows a better understanding of the induced disorder introduced by alloying in the A15 phase. So far, we have observed that Hf alloying of pure Nb can enhance H c2 (0) by 3-4 T to ~28 T, while adding just 1 at. %Hf or Zr into a Nb4Ta base alloy can raise H c2 (0) to ~31 T. Very importantly we find that Hf and Zr raise the alloy recrystallization temperature above the usual A15 reaction temperature range of 650°C – 750°C, thus ensuring denser A15 phase nucleation in the Nb alloy grain boundaries, possibly leading to a more homogeneous A15 phase Sn content and refined A15 grain size. Furthermore, the potential for further advancements in Nb 3 Sn properties is explored in relation to the recrystallization of the Nb alloy and the factors controlling the upper critical field.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nb 3 Sn Superconducting Cavities by Bronze Routes for Accelerator Stewardship

This project explored the challenges of making Nb 3 Sn superconducting radio-frequency (SRF) cavities by bronze routes. The SRF research community has prioritized Nb 3 Sn for many reasons, including the possibility to operate linacs for stewardship applications in continuous-wave mode with compact cryogenic systems. Existing Nb 3 Sn approaches use a cavity body made of niobium and apply tin to the polished cavity interior, a starting point that contains the main costs of present niobium cavity technology. Further complexity is then added because a high vacuum and temperature >1100 °C must be used to prevent formation of undesirable Nb-Sn phases, de-gas interstitial contaminants, and maintain the high purity of the Nb body. The project sought a more cost-effective solution for the same performance opportunities by exploiting the Cu-Sn-Nb diffusion reactions used to make Nb 3 Sn superconducting wires for magnets, which can be carried out at ~700 °C and are compatible with much cheaper copper cavity bodies. The project also sought understanding of the materials science and factors that affect superconducting properties. The project has impacted SRF cavity technology by demonstrating feasibility of alternative routes that enable compact, high-power electron accelerators for energy, security, environment, medical, and commercial applications.

43 PARTICLE ACCELERATORS↗

Origin of the enhanced Nb3Sn performance by combined Hf and Ta doping

Abstract In recent years there has been an increasing effort in improving the performance of Nb 3 Sn for high-field applications, in particular for the fabrication of conductors suitable for the realization of the Future Circular Collider (FCC) at CERN. This challenging task has led to the investigation of new routes to advance the high-field pinning properties, the irreversibility and the upper critical fields ( H Irr and H c2 , respectively). The effect of hafnium addition to the standard Nb-4Ta alloy has been recently demonstrated to be particularly promising and, in this paper, we investigate the origins of the observed improvements of the superconducting properties. Electron microscopy, Extended X-ray Absorption Fine Structure Spectroscopy (EXAFS) and Atom Probe Tomography (APT) characterization clearly show that, in presence of oxygen, both fine Nb 3 Sn grains and HfO 2 nanoparticles form. Although EXAFS is unable to detect significant amounts of Hf in the A15 structure, APT does indeed reveal some residual intragrain metallic Hf. To investigate the layer properties in more detail, we created a microbridge from a thin lamella extracted by Focused Ion Beam (FIB) and measured the transport properties of Ta-Hf-doped Nb 3 Sn. H c2 (0) is enhanced to 30.8 T by the introduction of Hf, ~ 1 T higher than those of only Ta-doped Nb 3 Sn, and, even more importantly the position of the pinning force maximum exceeds 6 T, against the typical ~ 4.5–4.7 T of the only Ta-doped material. These results show that the improvements generated by Hf addition can significantly enhance the high-field performance, bringing Nb 3 Sn closer to the requirements necessary for FCC realization.

36 MATERIALS SCIENCE↗

Direct evidence of microstructure dependence of magnetic flux trapping in niobium

Abstract Elemental type-II superconducting niobium is the material of choice for superconducting radiofrequency cavities used in modern particle accelerators, light sources, detectors, sensors, and quantum computing architecture. An essential challenge to increasing energy efficiency in rf applications is the power dissipation due to residual magnetic field that is trapped during the cool down process due to incomplete magnetic field expulsion. New SRF cavity processing recipes that use surface doping techniques have significantly increased their cryogenic efficiency. However, the performance of SRF Nb accelerators still shows vulnerability to a trapped magnetic field. In this manuscript, we report the observation of a direct link between flux trapping and incomplete flux expulsion with spatial variations in microstructure within the niobium. Fine-grain recrystallized microstructure with an average grain size of 10–50 µm leads to flux trapping even with a lack of dislocation structures in grain interiors. Larger grain sizes beyond 100–400 µm do not lead to preferential flux trapping, as observed directly by magneto-optical imaging. While local magnetic flux variations imaged by magneto-optics provide clarity on a microstructure level, bulk variations are also indicated by variations in pinning force curves with sequential heat treatment studies. The key results indicate that complete control of the niobium microstructure will help produce higher performance superconducting resonators with reduced rf losses 1 related to the magnetic flux trapping.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evidence of Kramer extrapolation inaccuracy for predicting high field Nb 3 Sn properties

Future applications requiring high magnetic fields, such as the proposed Future Circular Collider, demand a substantially higher critical current density, J c , at fields ≥16 T than is presently available in any commercial strand, so there is a strong effort to develop new routes to higher J c Nb 3 Sn. As a consequence, evaluating the irreversibility field (H irr ) of any new conductor to ensure reliable performance at these higher magnetic fields becomes essential. To predict the irreversibility field for Nb 3 Sn wires, critical current measurements, I c , are commonly performed in the 12-15 T range and the Kramer extrapolation is used to predict higher field properties. Here, the Kramer extrapolation typically models the contribution only for sparse grain boundary pinning, yet Nb 3 Sn wires rely on a high density of grain boundaries to provide the flux pinning that enables their high critical current density. However, whole-field range VSM measurements up to 30 T recently showed for Nb 3 Sn RRP® wires that the field dependence of the pinning force curve significantly deviates from the typical grain boundary shape, leading to a 1-2 T overestimation of Hirr when extrapolated from the typical mid-field data taken only up to about 15 T. In this work we characterized a variety of both RRP® and PIT Nb 3 Sn wires by transport measurements up to 29 T at the Laboratoire National des Champs Magnétiques Intenses (LNCMI), part of the European Magnetic Field Laboratory in Grenoble, to verify whether or not such overestimation is related to the measurement technique and whether or not it is a common feature across different designs. Indeed we also found that when measured in transport the 12-15 T Kramer extrapolation overestimates the actual H irr in both types of conductor with an inaccuracy of up to 1.6 T, confirming that high field characterization is a necessary tool to evaluate the actual high field performance of each Nb 3 Sn wire.

36 MATERIALS SCIENCE↗

Ta, Ti and Hf effects on Nb 3 Sn high-field performance: temperature-dependent dopant occupancy and failure of Kramer extrapolation

The increasing demand for improving the high-field (16-22 T) performance of Nb 3 Sn conductors requires a better understanding of the properties of modern wires much closer to irreversibility field, H Irr . In this study we investigated the impact of Ta, Ti and Hf doping on the high-field pinning properties, the upper critical field, H c2 , and H Irr . We found that the pinning force curves of commercial Ti and Ta doped wires at different temperatures do not scale and that the Kramer extrapolation, typically used by magnet designers to estimate high-field critical current density and magnet operational margins from lower field data, is not reliable and significantly overestimates the actual H Irr . In contrast, new laboratory scale conductors made with Nb-Ta-Hf alloy have improved high-field J c performance and, despite contributions by both grain boundary and point defect pinning mechanisms, have more predictable high-field behavior. Using Extended X-ray Absorption Fine Structure spectroscopy, EXAFS, we found that for the commercial Ta and Ti doped conductors, the Ta site occupancy in the A15 structure gradually changes with the heat treatment temperature whereas Ti is always located on the Nb site with clear consequences for H c2 . Finally, this work reveals the still limited understanding of what determines H c2 , H Irr and the high-field J c performance of Nb 3 Sn and the complexity of optimizing these conductors so that they can reach their full potential for high-field applications.

36 MATERIALS SCIENCE↗

Investigation of Precipitation and Segregation of Secondary Phase Byproducts in Intermetallic Superconducting Materials

For broader acceptance, the next generation of superconductors for high magnetic field appli-cations will need to be both higher performance and lower cost. In this work, we contrast two super-conductors that are candidates for high field magnets; Nb 3 Sn, which has a long history yet has seen renewed interest in recent years because of remarkable advances in its properties, and Fe-based superconductors that offer potentially low-costs and very high fields. TEM techniques are essential to understand how to engineer the desired micro-/nanostructure that ultimately defines the properties for these superconductors.

36 MATERIALS SCIENCE↗

Beneficial influence of Hf and Zr additions to Nb4at%Ta on the vortex pinning of Nb 3 Sn with and without an O source

In this paper we show that addition of Hf to Nb4Ta can significantly improve the high field performance of Nb 3 Sn, making it suitable for dipole magnets for a machine like the 100 TeV Future Circular Collider (FCC). A big challenge of the FCC is that the desired non-Cu critical current density (J c ) target of 1500 A mm –2 (16 T, 4.2 K) is substantially above the best present Nb 3 Sn conductors doped with Ti or Ta (~1300 A mm –2 in the very best sample of the very best commercial wire). Recent success with internal oxidation of Nb–Zr precursor has shown significant improvement in the layer J c of Nb 3 Sn wires, albeit with the complication of providing an internal oxygen diffusion pathway and avoiding degradation of the irreversibility field H Irr . We here extend the Nb1Zr oxidation approach by comparing Zr and Hf additions to the standard Nb4Ta alloy of maximum H c2 and H Irr . Nb4Ta rods with 1Zr or 1Hf were made into monofilament wires with and without SnO 2 and their properties measured over the entire superconducting range at fields up to 31 T. We found that Group IV alloying of Nb4Ta does raise H Irr , though O 2 addition still slightly degrades it. As noted in earlier Nb1Zr work with an O source, the pinning force density F p is strongly enhanced and its peak value shifted to higher field by internal oxidation. A surprising result of this work is that we found better properties in Nb4Ta1Hf without SnO 2 , F pMax achieving 2.35 times that of the standard Nb4Ta alloy, while the oxidized Nb4Ta1Zr alloy achieved 1.54 times that of the Nb4Ta alloy. The highest layer J c (16 T, 4.2 K) of 3700 A mm –2 was found in the SnO 2 -free wire made with Nb4Ta1Hf alloy. Using a standard A15 cross-section fraction of 60% for modern powder-in-tube and rod restack process wires, we estimated that a non-Cu J c of 2200 A mm –2 is obtainable in modern conductors, well above the 1500 A mm –2 FCC specification. Moreover, since the best properties were obtained without SnO 2 , the Nb4Ta1Hf alloy appears to open a straightforward route to enhanced properties in Nb 3 Sn wires manufactured by virtually all the presently used commercial routes employed today.

36 MATERIALS SCIENCE↗

Precipitous change of the irreversible strain limit with heat-treatment temperature in Nb 3 Sn wires made by the restacked-rod process

The intrinsic irreversible strain limit ε irr,0 of Nb 3 Sn superconducting wires, made by the restacked-rod process and doped with either Ti or Ta, undergoes a precipitous change as a function of temperature θ of the final heat-treatment for forming the A15 phase. Nb 3 Sn transitions from a highly brittle state where it cracks as soon as it is subjected to an axial tensile strain of any measurable amount, to a state more resilient to tensile strain as high as 0.4%. The remarkable abruptness of this transition (as most of it occurs over a range of only 10 °C) could pose real challenges for the heat-treatment of large magnets, such as those fabricated for the high-luminosity upgrade of the Large Hadron Collider (LHC). We named this behavior the strain irreversibility cliff (SIC) to caution magnet developers. The approach to fulfilling application requirements just in terms of the conductor’s residual resistivity ratio RRR and critical-current density J c is incomplete. Along with RRR and J c wire specifications, and sub-element size requirements that reduce wire magnetization and instabilities effects, SIC imposes additional constraints on the choice of heat-treatment conditions to ensure mechanical integrity of the conductor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Controlling Cu–Sn mixing so as to enable higher critical current densities in RRP ® Nb 3 Sn wires

Dipole magnets for the proposed Future Circular Collider (FCC) demand specifications significantly beyond the limits of all existing Nb 3 Sn wires, in particular a critical current density (J c ) of more than 1500 A mm -2 at 16 T and 4.2 K with an effective filament diameter (D eff ) of less than 20 μm. The restacked-rod-process (RRP ® ) is the technology closest to meeting these demands, with a J c (16 T) of up to 1400 A mm -2 , residual resistivity ratio > 100, for a sub-element size D s of 58 μm (which in RRP ® wires is essentially the same as D eff ). An important present limitation of RRP ® is that reducing the sub-element size degrades J c to as low as 900 A mm -2 at 16 T for D s = 35 μm. To gain an understanding of the sources of this J c degradation, we have made a detailed study of the phase evolution during the Cu–Sn 'mixing' stages of the wire heat treatment that occur prior to Nb 3 Sn formation. Using extensive microstructural quantification, we have identified in this paper the critical role that the Sn–Nb–Cu ternary phase (Nausite) can play. The Nausite forms as a well-defined ring between the Sn source and the Cu/Nb filament pack, and acts as an osmotic membrane in the 300 °C–400 °C range—greatly inhibiting Sn diffusion into the Cu/Nb filament pack while supporting a strong Cu counter-diffusion from the filament pack into the Sn core. This converts the Sn core into a mixture of the low melting point (408 °C) η phase (Cu 6 Sn 5 ) and the more desirable ε phase (Cu 3 Sn), which decomposes at 676 °C. After the mixing stages, when heated above 408 °C towards the Nb 3 Sn reaction, any residual η liquefies to form additional irregular Nausite on the inside of the membrane. All Nausite decomposes into NbSn 2 on further heating, and ultimately transforms into coarse-grain (and often disconnected) Nb 3 Sn which has little contribution to current transport. Understanding this critical Nausite reaction pathway has allowed us to simplify the mixing heat treatment to only one stage at 350 °C for 400 h which minimizes Nausite formation while encouraging the formation of the higher melting point ε phase through better Cu–Sn mixing. Finally, at a D s of 41 μm, the Nausite control heat treatment increases the J c at 16 T by 36%, reaching 1300 A mm -2 (i.e. 2980 A mm -2 at 12 T), and moving RRP ® closer to the FCC targets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evidence from EXAFS for Different Ta/Ti Site Occupancy in High Critical Current Density Nb 3 Sn Superconductor Wires

To meet critical current density, Jc, targets for the Future Circular Collider (FCC), the planned replacement for the Large Hadron Collider (LHC), the high field performance of Nb 3 Sn must be improved, but champion J c values have remained static for the last 10 years. Making the A15 phase stoichiometric and enhancing the upper critical field H c2 by Ti or Ta dopants are the standard strategies for enhancing high field performance but detailed recent studies show that even the best modern wires have broad composition ranges. To assess whether further improvement might be possible, we employed EXAFS to determine the lattice site location of dopants in modern high-performance Nb 3 Sn strands with J c values amongst the best so far achieved. Although Ti and Ta primarily occupy the Nb sites in the A15 structure, we also find significant Ta occupancy on the Sn site. These findings indicate that the best performing Ti-doped stand is strongly sub-stoichiometric in Sn and that antisite disorder likely explains its high average H c2 behavior. These new results suggest an important role for dopant and antisite disorder in minimizing superconducting property distributions and maximizing high field J c properties.

36 MATERIALS SCIENCE↗

Effect of low temperature baking in nitrogen on the performance of a niobium superconducting radio frequency cavity

Here, we report the rf performance of a single-cell superconducting radiofrequency cavity after low temperature baking in a nitrogen environment. A significant increase in quality factor has been observed when the cavity was heat treated in the temperature range of 120-160 °C with a nitrogen partial pressure of ~25 mTorr. This increase in quality factor as well as the Q-rise phenomenon (anti-Q-slope) is similar to those previously obtained with high temperature nitrogen doping as well as titanium doping. In this study, a cavity N 2 -treated at 120 °C and at 140 °C, showed no degradation in accelerating gradient, however the accelerating gradient was reduced by ~25% with a 160 °C N 2 treatment, compared to the baseline tests after electropolishing. Sample coupons treated in the same conditions as the cavity were analyzed by scanning electron microscope, x-ray photoelectron spectroscopy and secondary ion mass spectroscopy revealed a complex surface composition of Nb 2 O 5 , NbO and NbN (1-x) O x within the rf penetration depth. Furthermore, magnetization measurements showed no significant change on bulk superconducting properties.

36 MATERIALS SCIENCE↗

Improvement of small to large grain A15 ratio in Nb 3 Sn PIT wires by inverted multistage heat treatments

The next generation of superconducting accelerator magnets for the Large Hadron Collider at CERN will require large amounts of Nb 3 Sn superconducting wires and the Powder-In-Tube (PIT) process, which utilizes a NbSn 2 -rich powder core within tubes of Nb(7.5wt%Ta) contained in a stabilizing Cu matrix, is a potential candidate. But, the critical current density, J c , is limited by the formation of a large grain (LG) A15 layer which does not contribute to transport current, but occupies 25-30% of the total A15 area. Thus it is important to understand how this layer forms, and if it can be minimized in favor of the beneficial small grain (SG) A15 morphology which carries the supercurrent. The ratio of SG/LG A15 is our metric here, where an increase signals improvement in the wires A15 morphology distribution. We have made a critical new observation that the initiation of the LG A15 formation can be controlled at a wide range of temperatures relative to the formation of the small grain (SG) A15. The LG A15 can be uniquely identified as a decomposition product of the Nb6Sn5(Cu x ), surrounded by a layer of rejected Cu, thus the LG A15 is not only of low pin density, but is not continuous grain to grain. We have found that in single stage reactions limited to 630 °C - 690 °C, the maximum SG A15 layer thickness prior to LG A15 formation is very sensitive to temperature, with a maximum around 670 °C. This result led to the design of four novel heat treatments which all included a short, high temperature stage early in the reaction, followed by a slow cooling to a more typical reaction temperature of 630 °C. We also found that this heat treatment (HT) modification increased the SG A15 layer thickness while simultaneously suppressing LG A15 morphology, with no additional consumption of the diffusion barrier. In the best heat treatment the SG/LG A15 ratio improved by 30%. Unfortunately, J c values suffered slightly, however further exploration of this high temperature reaction region is required to understand the limits to A15 formation in Nb3Sn PIT conductors.

36 MATERIALS SCIENCE↗

Evaluation of critical current density and residual resistance ratio limits in powder in tube Nb 3 Sn conductors

High critical current density (Jc) Nb 3 Sn A15 multifilamentary wires require a large volume fraction of small grain, superconducting A15 phase, as well as Cu stabilizer with high Residual Resistance Ratio (RRR) to provide electromagnetic stabilization and protection. In Powder-in-Tube (PIT) wires the unreacted Nb7.5wt.%Ta outer layer of the tubular filaments acts as a diffusion barrier and protects the interfilamentary Cu stabilizer from Sn contamination. A high RRR requirement generally imposes a restricted A15 reaction heat treatment (HT) to prevent localized full reaction of the filament that could allow Sn to reach the Cu. In this paper we investigate recent high quality PIT wires that achieve a J c (12 T, 4.2 K) up to ~2500 A/mm -2 and find that the minimum diffusion barrier thickness decreases as the filament aspect ratio increases from ~1 in the inner rings of filaments to 1.3 in the outer filament rings. We found that just 2-3 diffusion barrier breaches can degrade RRR from 300 to 150 or less. Using progressive etching of the Cu we also found that the RRR degradation is localized near the external filaments where deformation is highest. Consequently minimizing filament distortion during strand fabrication is important for reducing RRR degradation. The additional challenge of developing the highest possible J c must be addressed by forming the maximum fraction of high J c small-grain (SG) A15 and minimizing low J c large-grain (LG) A15 morphologies. Finally, in one wire we found that 15% of the filaments had a significantly enhanced SG/LG A15 ratio and no residual A15 in the core, a feature that opens a path to substantial J c improvement.

36 MATERIALS SCIENCE↗

Metallographic autopsies of full-scale ITER prototype cable-in-conduit conductors after full cyclic testing in SULTAN: III. The importance of strand surface roughness in long twist pitch conductors

As part of the ITER conductor qualification process, 3 m long Cable-in-Conduit Conductors (CICCs) were tested at the SULTAN facility under conditions simulating ITER operation so as to establish the current sharing temperature, T cs , as a function of multiple full Lorentz force loading cycles. After a comprehensive evaluation of both the Toroidal Field (TF) and the Central Solenoid (CS) conductors, it was found that T cs degradation was common in long twist pitch TF conductors while short twist pitch CS conductors showed some T cs increase. However, one kind of TF conductors containing superconducting strand fabricated by the Bochvar Institute of Inorganic Materials (VNIINM) avoided T cs degradation despite having long twist pitch. In our earlier metallographic autopsies of long and short twist pitch CS conductors, we observed a substantially greater transverse strand movement under Lorentz force loading for long twist pitch conductors, while short twist pitch conductors had negligible transverse movement. With help from the literature, we concluded that the transverse movement was not the source of T cs degradation but rather an increase of the compressive strain in the Nb 3 Sn filaments possibly induced by longitudinal movement of the wires. Like all TF conductors this TF VNIINM conductor showed large transverse motions under Lorentz force loading, but Tcs actually increased, as in all short twist pitch CS conductors. We here propose that the high surface roughness of the VNIINM strand may be responsible for the suppression of the compressive strain enhancement (characteristic of long twist pitch conductors). Furthermore, it appears that increasing strand surface roughness could improve the performance of long twist pitch CICCs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Large grain CBMM Nb ingot slices: An ideal test bed for exploring the microstructure-electromagnetic property relationships relevant to SRF

High purity (RRR > 200), large grain (> 5-10 cm) niobium ingot slices have been successfully used to fabricate radio frequency (RF) cavities for particle accelerators. They offer significantly reduced fabrication cost by eliminating processing steps and furthermore they provide the opportunity to study the influence of individual grain boundaries in SRF Nb. Here we summarize our measurements of grain boundary (GB) effects on the superconducting properties of large grain high purity niobium sheet manufactured by CBMM. We show by magneto-optical (MO) imaging that GBs allow premature flux penetration, but only when they are oriented close to the direction of the magnetic field. However, even low angle GBs produced by minor deformations commensurate with half-cell forming produce localized flux penetration. The transport properties of grain boundaries were investigated by direct transport across them and evidence for preferential vortex flow along the GBs of SRF Nb was observed for the first time. Using transmission electron microscopy (TEM) and micro crystallographic analysis with electron backscattered diffraction (EBSD), we were able to quantitatively characterize surface substructures that can lead to localized thermal breakdown of superconductivity. Important to these studies was the development of sample preparation techniques that made the cutout single, bi-crystal and tri-crystal Nb coupons as representative as possible of the surface properties of cavities manufactured by standard techniques.

36 MATERIALS SCIENCE↗

Determination of bulk and surface superconducting properties of N 2 -doped cold worked, heat treated and electro-polished SRF grade niobium

In this study, nitrogen-doped cavities show significant performance improvement in the medium accelerating field regime due to a lowered RF surface resistivity. However, the mechanism of enhancement has not been clearly explained. Our experiments explore how N 2 -doping influences Nb bulk and surface superconducting properties, and compare the N 2 -doped properties with those obtained previously with conventionally treated samples. High purity Nb-rod was mechanically deformed and post treated based on a typical SRF cavity treatment recipe. The onset of flux penetration at H c1 , and the upper and the surface critical fields, H c2 and H c3 , were characterized by magnetic hysteresis and AC susceptibility techniques. The surface depth profile responsible for superconductivity was examined by changing AC amplitude in AC susceptibility, and the microstructure was directly observed with EBSD-OIM. We are also investigating surface chemistry for detailed composition using XPS. We have found that N 2 -doping at 800 °C significantly reduces the H c3 /H c2 ratio towards the ideal value of ~1.7, and conclude that AC susceptibility is capable of following changes to the surface properties induced by N 2 -doping.

36 MATERIALS SCIENCE↗

Metallographic autopsies of full-scale ITER prototype cable-in-conduit conductors after full cyclic testing in SULTAN: II. Significant reduction of strand movement and strand damage in short twist pitch CICCs

Prototype cable in conduit conductors (CICCs) destined for use in the Toroidal Field (TF) and Central Solenoid (CS) coils of the ITER experimental fusion reactor underwent severe cyclic loading in the SULTAN facility. Their autopsies revealed significant and permanent transverse strand migration due to the large Lorentz forces of the SULTAN test. The movement resulted in a 3 7% void fraction increase on the Low Pressure (LP) side of the longer twist pitch CICCs. However, short twist pitch conductors exhibited less than 1% void fraction increase in the LP side, as well as a complete absence of the Nb 3 Sn filament fractures observed in the longer twist pitch conductors. We report here a detailed strand to cable analysis of short and longer “baseline” twist pitch CICCs. It was found that the use of Internal Tin strands in the longer “baseline” twist pitch CICCs can be beneficial possibly because of their superior stiffness—which better resist strand movement—while the use of Bronze Process strands showed more movement and poorer cyclic test performance. This was not the case for the short twist pitch CICC. Such conductor design seems to work well with both strand types. But it was found that despite the absence of filament fractures, the short twist pitch CICC made from the Internal Tin strands studied here developed severe strand distortion during cabling which resulted in diffusion barrier breaks and Sn contamination of the Cu stabilizer during the heat treatment. Furthermore, the short twist pitch CICC made from Bronze Process strands preserved diffusion barrier integrity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗