Engineering topics

Lee, Seung-Kuk

Publications and source records attributed to Lee, Seung-Kuk.

9 records

NASA NTRS2019

Rapid Generation of Flood Maps Using Dual-Polarimetric Synthetic Aperture Radar Imagery

Rapid generation of synthetic aperture radar (SAR) based flood extent and flood depth maps provide valuable data in disaster response efforts. We present a simple but powerful method using dual-polarimetric SAR imagery. A RGB false-color map is generated using pre- and post-flooding imagery, allowing operators to distinguish between existing standing water in pre-flooding data and recently flooded areas. This method works very well in areas of standing water, while large omission errors can be seen in urban areas due to the double-bounce effect. A flood depth map is also estimated by using an external DEM. Compared with FEMA flood product, flood water depth from the proposed method showed low bias with small dispersion. This automatic flood mapping system will contribute to the rapid assessment for disaster relief efforts.

Jo, MinJeong↗

NASA NTRS2019

Adaptive Antenna Pattern Notching of Interference in Synthetic Aperture Radar Data Using Digital Beamforming

Radio Frequency Interference (RFI) is a growing problem in Synthetic Aperture Radar (SAR)systems as scientific motivations push the radars to lower frequencies and as more wireless services share the frequency spectrum. New, advanced SAR instruments, such as NASA's EcoSAR, DBSAR and DLR's Tandem-L mission, employ a multichannel architecture capable of Digital Beamforming (DBF). Radars with DBF are capable of notching the antenna pattern in specific directions, which can be utilized to suppress RFI on board or in post-processing. A well-researched beamformer for this purpose is the Minimum Variance Distortionless Response (MVDR) Beamformer. However, the number of interferers that can be removed through notching is limited by the number of receive channels. It is therefore essential to adaptively change the antenna pattern notching throughout the image in time and frequency for the best results with a given number of receive channels. In this paper, we present several methods to achieve this notching by making use of the spatial SAR signal distribution in range time, range frequency, azimuth time and azimuth Doppler that is inherent to the SAR imaging geometry. Because this distribution is time-variable and yet predictable, it can be used to improve the angle of arrival estimation of the RFI and the adaptive notching. The presented methods can be applied to a Digital Beamforming (DBF) SAR signal with multiple channels in elevation and/or in azimuth. Simulations show that the proposed methods increase the ability to notch out-of-swath interference from multiple directions and lessen the impact on in-swath interference. The improvement of the interferometric coherence for a single-pass interferogram acquired by NASA's EcoSAR system (capable of DBF in elevation) is demonstrated. The removal of periodic RFI artifacts is achieved.

RFI↗

NASA NTRS2018

Vegetation Height Estimate in Rice Fields Using Single Polarization TanDEM-X Science Phase Data

This study presents the retrieval of rice paddy height using single polarization (single-pol) interferometric SAR (InSAR) data by means of model-based height inversion without an external DEM. A total of eight TanDEM-X (TDX) scenes were used and the TDX images were; acquired using a large cross-track baseline configuration during the TDX Science Phase (June–August 2015). A single-pol inversion approach for a flooded rice field is proposed and evaluated over the Buan test site in South Korea. A novel approach is adopted for the estimation of the ground (i.e., water level) interferometric phase within a flooded rice paddy from TDX data acquired during a period of early rice growth. It is consequently possible to apply the model-based inversion algorithm to the single-pol InSAR data. Rice height maps during the rice growth cycle presented and validated by field measurements. The results demonstrated the high performance of the inversion with a correlation coefficient of 0.78 and an RMSE of 0.10 m. The proposed methodology will be useful to monitor rice plants and to predict a gross rice yield, along with dual and fully polarimetric interferometric SAR data.

Lee, Seung-Kuk↗

NASA NTRS2018

Multibaseline TanDEM-X Mangrove Height Estimation: The Selection of the Vertical Wavenumber

We generated a large-scale mangrove forest height map using multiple TanDEM-X (TDX) interferometric synthetic aperture radar (InSAR) acquisitions with various spatial baselines in order to improve the height estimation accuracy across a wide range of forest heights. The forest height inversion using InSAR data is strongly dependent upon the vertical wavenumber (i.e., perpendicular baseline). First, we investigated the role of the vertical wavenumber in forest height inversion from InSAR data using the sensitivity of the interferometric (volume) coherence to forest height. We used corrected but lower resolution and accuracy Shuttle Radar Topography Mission (SRTM) mangrove height maps as a priori information over Akanda and Pongara National Parks in Gabon to estimate lower and upper boundaries of the vertical wavenumber over test sites from the measured coherence-to-height sensitivity. Only TDX acquisitions within the boundaries of the vertical wavenumber were selected and combined for multibaseline mangrove height inversion. Mangrove forest height was obtained with multibaseline TDX acquisitions and was validated against the reference height derived from field measurement data providing improvements in multibaseline inversion over existing height estimates (i.e., SRTM height) and single-baseline inversions (multibaseline inversion: r(exp 2) = 0.98, root mean square error (RMSE) of 2.73 m; SRTM height: r(exp 2) = 0.86, RMSE = 7.21 m; single-baseline inversions: r(exp 2) = 0.08-0.97, RMSE = 3.86-11.10 m). As a result, to accurately estimate forest heights over a wide range (3-60 m), multibaseline InSAR acquisitions (at least three different baselines) are needed to exclude biases associated with the vertical wavenumber in forest height inversion.

vertical wavenumber.↗

NASA NTRS2017

High-Accuracy Tidal Flat Digital Elevation Model Construction Using TanDEM-X Science Phase Data

This study explored the feasibility of using TanDEM-X (TDX) interferometric observations of tidal flats for digital elevation model (DEM) construction. Our goal was to generate high-precision DEMs in tidal flat areas, because accurate intertidal zone data are essential for monitoring coastal environment sand erosion processes. To monitor dynamic coastal changes caused by waves, currents, and tides, very accurate DEMs with high spatial resolution are required. The bi- and monostatic modes of the TDX interferometer employed during the TDX science phase provided a great opportunity for highly accurate intertidal DEM construction using radar interferometry with no time lag (bistatic mode) or an approximately 10-s temporal baseline (monostatic mode) between the master and slave synthetic aperture radar image acquisitions. In this study, DEM construction in tidal flat areas was first optimized based on the TDX system parameters used in various TDX modes. We successfully generated intertidal zone DEMs with 57-m spatial resolutions and interferometric height accuracies better than 0.15 m for three representative tidal flats on the west coast of the Korean Peninsula. Finally, we validated these TDX DEMs against real-time kinematic-GPS measurements acquired in two tidal flat areas; the correlation coefficient was 0.97 with a root mean square error of 0.20 m.

Lee, Seung-Kuk↗

NASA NTRS2016

Ground-Level Digital Terrain Model (DTM) Construction from Tandem-X InSAR Data and Worldview Stereo-Photogrammetric Images

The ground-level digital elevation model (DEM) or digital terrain model (DTM) information are invaluable for environmental modeling, such as water dynamics in forests, canopy height, forest biomass, carbon estimation, etc. We propose to extract the DTM over forested areas from the combination of interferometric complex coherence from single-pass TanDEM-X (TDX) data at HH polarization and Digital Surface Model (DSM) derived from high-resolution WorldView (WV) image pair by means of random volume over ground (RVoG) model. The RVoG model is a widely and successfully used model for polarimetric SAR interferometry (Pol-InSAR) technique for vertical forest structure parameter retrieval [1][2][3][4]. The ground-level DEM have been obtained by complex volume decorrelation in the RVoG model with the DSM using stereo-photogrammetric technique. Finally, the airborne lidar data were used to validate the ground-level DEM and forest canopy height results.

Lee, Seung-Kuk↗

NASA NTRS2015

High-Resolution Forest Canopy Height Estimation in an African Blue Carbon Ecosystem

Mangrove forests are one of the most productive and carbon dense ecosystems that are only found at tidally inundated coastal areas. Forest canopy height is an important measure for modeling carbon and biomass dynamics, as well as land cover change. By taking advantage of the flat terrain and dense canopy cover, the present study derived digital surface models (DSMs) using stereophotogrammetric techniques on high-resolution spaceborne imagery (HRSI) for southern Mozambique. A mean-weighted ground surface elevation factor was subtracted from the HRSI DSM to accurately estimate the canopy height in mangrove forests in southern Mozambique. The mean and H100 tree height measured in both the field and with the digital canopy model provided the most accurate results with a vertical error of 1.18-1.84 m, respectively. Distinct patterns were identified in the HRSI canopy height map that could not be discerned from coarse shuttle radar topography mission canopy maps even though the mode and distribution of canopy heights were similar over the same area. Through further investigation, HRSI DSMs have the potential of providing a new type of three-dimensional dataset that could serve as calibration/validation data for other DSMs generated from spaceborne datasets with much larger global coverage. HSRI DSMs could be used in lieu of Lidar acquisitions for canopy height and forest biomass estimation, and be combined with passive optical data to improve land cover classifications.

HRSI↗

NASA NTRS2014

Polarimetric SAR Interferometry Evaluation in Mangroves

TanDEM-X (TDX) enables to generate an interferometric coherence without temporal decorrelation effect that is the most critical factor for a successful Pol-InSAR inversion, as have recently been used for forest parameter retrieval. This paper presents mangrove forest height estimation only using single-pass/single-baseline/dual-polarization TDX data by means of new dual-Pol-InSAR inversion technique. To overcome a lack of one polarization in a conventional Pol- InSAR inversion (i.e. an underdetermined problem), the ground phase in the Pol-InSAR model is directly estimated from TDX interferograms assuming flat underlying topography in mangrove forest. The inversion result is validated against lidar measurement data (NASA's G-LiHT data).

Mangrove↗

NASA NTRS2014

Development of NASA's Next Generation L-Band Digital Beamforming Synthetic Aperture Radar (DBSAR-2)

NASA's Next generation Digital Beamforming SAR (DBSAR-2) is a state-of-the-art airborne L-band radar developed at the NASA Goddard Space Flight Center (GSFC). The instrument builds upon the advanced architectures in NASA's DBSAR-1 and EcoSAR instruments. The new instrument employs a 16-channel radar architecture characterized by multi-mode operation, software defined waveform generation, digital beamforming, and configurable radar parameters. The instrument has been design to support several disciplines in Earth and Planetary sciences. The instrument was recently completed, and tested and calibrated in a anechoic chamber.

SAR↗