Mission Concept Considerations for Ocean World Exploration Using RPS Inside a Pressure Vessel
No abstract provided
Donitz, Benjamin↗
Engineering topics
Lee, Young H.
Publications and source records attributed to Lee, Young H..
Thermal Analysis of Landers using Radioisotope Power Systems on Ice Worlds
The surfaces of Ice Worlds record evidence of interior processes, chemical potential, habitability, and potentially life within the interior. Volatile and organic chemistry at the surface is critical in determining habitability and detecting the presence of past or extant life. Radioisotope Power Systems (RPS) could be an enabling technology for in situ missions to ice worlds, providing both power and heat for long durations where solar power would not be feasible. However, it is necessary to understand the potential impact of RPS upon the local environment, to ensure that the rejected heat from RPS does not compromise science measurements or planetary protection requirements. To address these concerns, an RPS Ice World Lander Study was carried out in 2019 to investigate possible requirements on RPS surface mission concepts and approaches to excess heat management. The study focused on two destinations that are representative of the range of potential environments: Europa and Enceladus.Initial analysis showed that, due to the very low pressures on the surfaces of most ice world targets, surface melting does not occur because the water ice does not meet the triple-point. A 4 kW heat source suspended above the surface of Europa or Enceladus would not cause any melting, only sublimation.The study used a surface sublimation limit of 10 cm over a two-year period (the baseline for the recent Europa Lander study). To stay within this limit, Europa, with its relatively warm surface, could tolerate only 10 W/m2 of surface heat flux. Enceladus, with its relatively cold pure ice composition, could tolerate up to 100 W/m2.Various lander and heat shield configurations were analyzed for their heat flux radiated from the RPS to the surface. For a given heat shield configuration, the study team determined the minimum height of the RPS above the surface for which the heat flux would be within the accepted parameters for Europa and for Enceladus. Based on these thermal analyses, such RPS-powered landers could remain compliant with science investigation and planetary protection requirements with only modest mass allocated to spacecraft thermal accommodations.
Perl, Scott↗
Astro-biological Exploration of Ocean Worlds, Enabled by an RPS Inside a Pressure Vessel
Exploring Ocean and Ice Worlds could help us to understand the origin and evolution of life in the universe. In our solar system we have identified six Ocean and Ice Worlds, namely Earth, Europa, Ganymede, Callisto, Enceladus, and Titan. Other potential targets include Dione, Triton, and Pluto. As documented in the Planetary Decadal Survey [1] and the NASA Roadmap to Ocean Worlds [2], these worlds are compelling science destinations, with oceans situated below their tens of kilometers thick ice shells. To reach them we need a new exploration paradigm with novel technological solutions. Key technological challenges revolve around the power for the probe and for melting, as well as protecting the payload against the extreme environments, including high pressure, low temperature, corrosion, and radiation. Far away from the Sun, and melted into the ice, we may only rely on long-lived internal power generation. Radioisotope Power Systems (RPS) with either static or dynamic conversion, utilizing the heat of decaying Plutonium-238, could be good candidates. We need suitable payloads that are protected and could survive the extreme environments, as well as enabling power and thermal systems for melting through the ice shield and to swim in the ocean below the ice. RPS could support the probe’s instruments and sub-systems, as well as provide a heat source for melting the ice while keeping the components at operating temperatures. Mitigating the external pressure while immersing inside the ice shell, and in the ocean, would require a new RPS design that operates inside a Pressure Vessel. In our paper, we will discuss general mission architecture trades and the sizing of a next generation RPS housed in a pressure vessel, broadly applicable to any of the Ocean Worlds satellites of interest. Through a technology focused approach, we address interconnected design and mission architecture aspects, including considerations for: the RPS and the Pressure Vessel; extreme environmental constraints; g-load tolerance; power and thermal systems sizing for science measurements; spacecraft operations through all mission phases; subsurface mobility; and planetary protection. The findings will inform the science community on instrument accommodation possibilities; the mission planning community on possible mission concepts; and the RPS development community on the science driven technology considerations.
Donitz, Benjamin P.↗
Astro-Biological Exploration of Ocean Worlds, Enabled by an RPS Inside a Pressure Vessel
No abstract provided
Donitz, Benjamin P.↗
An Exploration of Mission Concepts That Could Utilize Small RPS
The NASA Radioisotope Power Systems (RPS) Program Mission Analysis Team at the Jet Propulsion Laboratory (JPL) requested a JPL Innovation Foundry Architecture Team (A-Team) study to assess mission pull for small RPS (1 mWe - 40 We) in order to inform the RPS Program Office on what future power system developments should be focused on. The A-Team is JPL’s concurrent engineering design team for science definition and early mission concept development, targeting concept maturation levels of 1 through 3. The requested small RPS study was tasked to identify the architecture space of potential small RPS missions, and suggest power levels that could enable or enhance potential future small spacecraft missions. This paper describes the collaborative engineering processes that the A-Team and Mission Analysis Team used to reach results quickly and the findings to inform the RPS Program about mission concept power requirements on RPS for small missions.
Bairstow, Brian K.↗
Novel antibody reagents for characterization of drug- and tumor microenvironment-induced changes in epithelial-mesenchymal transition and cancer stem cells
The presence of cancer stem cells (CSCs) and the induction of epithelial-to-mesenchymal transition (EMT) in tumors are associated with tumor aggressiveness, metastasis, drug resistance, and poor prognosis, necessitating the development of reagents for unambiguous detection of CSC- and EMT-associated proteins in tumor specimens. To this end, we generated novel antibodies to EMT- and CSC-associated proteins, including Goosecoid, Sox9, Slug, Snail, and CD133. Importantly, unlike several widely used antibodies to CD133, the anti-CD133 antibodies we generated recognize epitopes distal to known glycosylation sites, enabling analyses that are not confounded by differences in CD133 glycosylation. For all target proteins, we selected antibodies that yielded the expected target protein molecular weights by Western analysis and the correct subcellular localization patterns by immunofluorescence microscopy assay (IFA); binding selectivity was verified by immunoprecipitation-mass spectrometry and by immunohistochemistry and IFA peptide blocking experiments. Finally, we applied these reagents to assess modulation of the respective markers of EMT and CSCs in xenograft tumor models by IFA. We observed that the constitutive presence of human hepatocyte growth factor (hHGF) in the tumor microenvironment of H596 non-small cell lung cancer tumors implanted in homozygous hHGF knock-in transgenic mice induced a more mesenchymal-like tumor state (relative to the epithelial-like state when implanted in control SCID mice), as evidenced by the elevated expression of EMT-associated transcription factors detected by our novel antibodies. Similarly, our new anti-CD133 antibody enabled detection and quantitation of drug-induced reductions in CD133-positive tumor cells following treatment of SUM149PT triple-negative breast cancer xenograft models with the CSC/focal adhesion kinase (FAK) inhibitor VS-6063. Thus, our novel antibodies to CSC- and EMT-associated factors exhibit sufficient sensitivity and selectivity for immunofluorescence microscopy studies of these processes in preclinical xenograft tumor specimens and the potential for application with clinical samples.
Science & Technology - Other Topics↗
Radioisotope Power Systems: Considerations for use of Dynamic versus Static Conversion Technologies for NASA Missions
For more than five decades, Radioisotope Power Systems (RPS) have played a critical role in the exploration of space, enabling missions of scientific discovery to destinations across the solar system by providing electrical power to explore remote, challenging and extreme environments. In particular, RPS enable deep space missions where increased heliocentric distances reduce the ability of solar power to adequately meet spacecraft and instruments power requirements. Some previous notable missions that were enabled by RPS include Nimbus III, the Apollo Sur-face Experiments, the Pioneers 10 and 11, the Viking Mars Landers, Galileo, Ulysses, Cassini, New Horizons and Curiosity. The current operating set of missions that are enabled by RPS are Voyagers 1 and 2, Cassini, New Hori-zons, and Curiosity. The Multi-Mission Radioisotope Thermal Generator (MMRTG) is the current RPS used for mis-sions. An enhanced version of this generator outfitted with higher efficiency thermoelectrics is under development for potential use in the future. There are also current development efforts underway by NASA to explore dynamic power conversion systems such as Brayton and Stirling. This paper will compare and contrast the pros and cons of a generalized dynamic system with the current state-of-the-art thermoelectric static conversion system. The reason for this paper is to calmly analyze the pros and cons so that all the pertinent factors are placed under the same examination light with equal brightness. As with any purchase made the “newness” of certain items sometimes overrides a needed desire to fully vet all characteristics of the merchandise so that the best choice is made. The following areas will be specifically examined and discussed as they may impact the choice of radioisotope power system for a specific mission: • Projected power output to weight ratio (We/kg) • Amount of Pu-238 required per a fixed power output • Excess heat available to be rejected or used • Fueling operations during assembly by the Department of Energy (DOE) • Planetary protection protocol during fueling and testing of RPS • Transportation operations from DOE assembly site to Kennedy Space Center (KSC) • Remote operations at KSC prior to launch during Assembly Test and Launch Operations (ATLO) phase o Timing of the placement of the RPS onto spacecraft/rover o Off-normal operations at KSC
99 GENERAL AND MISCELLANEOUS↗
Assembly, Test and Launch Operations for a Nuclear-enabled NASA Mission: Considerations that are Specific to Use of a Nuclear Payload
For more than five decades, Radioisotope Power Systems (RPS) have played a critical role in the exploration of space, enabling missions of scientific discovery to destinations across the solar system by providing electrical power to explore remote, challenging and extreme environments. In particular, RPS enable deep space missions where increased heliocentric distances reduce the ability of solar power to adequately meet spacecraft and instruments power requirements. Some previous notable missions that were enabled by RPS include Nimbus III, the Apollo Surface Experiments, the Pioneers 10 and 11, the Viking Mars Landers, Galileo, Ulysses, Cassini, New Horizons and Curiosity. The current operating set of missions that are enabled by RPS are Voyagers 1 and 2, Cassini, New Horizons, and Curiosity. The Multi-Mission Radioisotope Thermal Generator (MMRTG) is the current RPS used for missions. An enhanced version of this generator outfitted with higher efficiency thermoelectrics is under development for potential use in the future. Other previously deployed power systems include the Multi-hundred Watt Radisotope Thermo-electric Generator (MHW RTG) and the General Purpose Heat Source Radisotope Thermo-electric Generator (GPHS RTG). The common thread for all of these power systems is that they are fueled with Pu-238. The use of this unique isotope involves additional planning activities and requires specific actions when the devices are delivered to Kennedy Space Center (KSC), launch site, and incorporated into the assembly, test and launch operations (ATLO) process to ensure mission success, met safety and security challenges. It has been forecasted that the use of a nuclear reactor system is on the horizon. This system could be used for either specifically powering S/C propulsion system or for surface power use once the mission arrived at its destina-tion. Since a nuclear-fission-based system has never been handled or integrated into a spacecraft at KSC, this nuclear reactor system would potentially require further challenges that must be accounted for in the ATLO process. This paper will explain ATLO considerations for the recent RTG-enabled launches that have occurred and planned in the near future (Mars 2020 NASA mission). It will also describe where further challenges that need to be met for the placement of a nuclear reactor (either for propulsion or transportation for surface power use) onto a space mission. Specifically, the following topics will be addressed: • Approach for nuclear safety planning for nuclear material use and its transportation to launch site • Planning for security posture for nuclear materials at launch site • Preparation for transportation of the nuclear power system from the fueling/testing location to the launch site • Preparation of documentation and procedures for nuclear material use at launch site • Planning for coordination between power system and space mission groups • Planning for appropriate staffing and scheduling of operations
07 ISOTOPE AND RADIATION SOURCES↗
Radioisotope Power Systems (RPS) for Emerging Power Needs of Deep Space Cubesats, Smallsats and Deployed Payloads
No abstract available
Lee, Young H.↗
Enabling Future Low-Cost Small Spacecraft Mission Concepts Using Small Radioisotope Power Systems
For more than five decades, Radioisotope Power Systems (RPS) have played a critical role in the exploration of space, enabling missions of scientific discovery to destinations across the solar system by providing electrical power to explore remote and challenging environments - some of the hardest to reach, darkest, and coldest locations in the solar system. In particular, RPS has met the demand of many long-duration mission concepts for continuous power to conduct science investigations independent of change in sunlight or variations in surface conditions like shadows, thick clouds, or dust.
Lee, Young H.↗
Development and Execution of Autonomous Procedures Onboard the International Space Station to Support the Next Phase of Human Space Exploration
Now that major assembly of the International Space Station (ISS) is complete, NASA's focus has turned to using this high fidelity in-space research testbed to not only advance fundamental science research, but also demonstrate and mature technologies and develop operational concepts that will enable future human exploration missions beyond low Earth orbit. The ISS as a Testbed for Analog Research (ISTAR) project was established to reduce risks for manned missions to exploration destinations by utilizing ISS as a high fidelity micro-g laboratory to demonstrate technologies, operations concepts, and techniques associated with crew autonomous operations. One of these focus areas is the development and execution of ISS Testbed for Analog Research (ISTAR) autonomous flight crew procedures intended to increase crew autonomy that will be required for long duration human exploration missions. Due to increasing communications delays and reduced logistics resupply, autonomous procedures are expected to help reduce crew reliance on the ground flight control team, increase crew performance, and enable the crew to become more subject-matter experts on both the exploration space vehicle systems and the scientific investigation operations that will be conducted on a long duration human space exploration mission. These tests make use of previous or ongoing projects tested in ground analogs such as Research and Technology Studies (RATS) and NASA Extreme Environment Mission Operations (NEEMO). Since the latter half of 2012, selected non-critical ISS systems crew procedures have been used to develop techniques for building ISTAR autonomous procedures, and ISS flight crews have successfully executed them without flight controller involvement. Although the main focus has been preparing for exploration, the ISS has been a beneficiary of this synergistic effort and is considering modifying additional standard ISS procedures that may increase crew efficiency, reduce operational costs, and raise the amount of crew time available for scientific research. The next phase of autonomous procedure development is expected to include payload science and human research investigations. Additionally, ISS International Partners have expressed interest in participating in this effort. The recently approved one-year crew expedition starting in 2015, consisting of one Russian and one U.S. Operating Segment (USOS) crewmember, will be used not only for long duration human research investigations but also for the testing of exploration operations concepts, including crew autonomy.
beyond low earth orbit (BLEO)↗
The International Space Station: Unique In-Space Testbed as Exploration Analog
Final assembly of the International Space Station (ISS) was completed in 2011. As articulated in the 2011 NASA Strategic Plan, the Agency's first goal is to extend and sustain human activities across the solar system. Thus, the emerging NASA vision is to launch a bold and ambitious new space initiative to enable human space exploration beyond low-Earth orbit to Lagrange points, the moon, near-Earth asteroids (NEAs), and Mars and its environs. To accomplish this vision, it is necessary to develop and validate innovative exploration technologies and operational concepts. With the extended life of the ISS to 2020 and possibly 2028, NASA has a mandate to maximize the potential of the Nation's newest National Laboratory. Exploration and ISS teams within NASA's Human Exploration and Operations Mission Directorate (HEOMD) have initiated a cooperative effort: the ISS Testbed for Analog Research (ISTAR), a high-fidelity operational analog that complements existing NASA terrestrial laboratory and field testing. To maximize use of the ISS platform to evaluate new exploration technologies, capabilities, and operational concepts to better comprehend and mitigate human spaceflight risks, ISTAR seeks out and encourages investigations dubbed "exploration detailed test objectives" (xDTOs). These xDTOs, building blocks of ISTAR missions, develop and optimize the operations concepts and the use of new technologies that should reduce risks and challenges facing astronauts on long exploration spaceflight voyages. In this paper, we describe (1) the rationale behind ISTAR, (2) a five-year strategic plan, (3) the approach for mission formulation, development, integration, and execution, (4) concepts for near-term missions that implement a phased approach for using ISS as an exploration testbed, and (5) the planned Mars mission simulation using the ISS. This paper will also document several challenges ISTAR must address to execute its missions.
Analog Mission↗
Infusing Stretch Goal Requirements into the Constellation Program
In 2004, the Vision for Space Exploration (VSE) was announced by the United States President's Administration in an effort to explore space and to extend a human presence across our solar system. Subsequently, the National Aeronautics and Space Administration (NASA) established the Exploration Systems Mission Directorate (ESMD) to develop a constellation of new capabilities, supporting technologies, and foundational research that allows for the sustained and affordable exploration of space. Then, ESMD specified the primary mission for the Constellation Program to carry out a series of human expeditions, ranging from Low Earth Orbit (LEO) to the surface of Moon, Mars, and beyond for the purposes of conducting human exploration of space. Thus, the Constellation Program was established at the Lyndon B. Johnson Space Center (JSC) to manage the development of the flight and ground infrastructure and systems that can enable continued and extended human access to space. Constellation Program's "Design Objectives" call for an early attention to the program's life cycle costs management through the Program's Need, Goals, and Objectives (NGO) document, which provides the vision, scope, and key areas of focus for the Program. One general policy of the Constellation Program, found in the Constellation Architecture Requirements Document (CARD), states: "A sustainable program hinges on how effectively total life cycle costs are managed. Developmental costs are a key consideration, but total life cycle costs related to the production, processing, and operation of the entire architecture must be accounted for in design decisions sufficiently to ensure future resources are available for ever more ambitious missions into the solar system....It is the intent of the Constellation Program to aggressively manage this aspect of the program using the design policies and simplicity." To respond to the Program's strong desire to manage the program life cycle costs, special efforts were established to identify operability requirements to influence flight vehicle and ground infrastructure design in order to impact the life cycle operations costs, and stretch goal requirements were introduced to the Program. This paper will describe how these stretch goal requirements were identified, developed, refined, matured, approved, and infused into the CARD. The paper will also document several challenges encountered when infusing the stretch goal requirements into the Constellation Program.
Operability↗
Interoperable Solution for Test Execution in Various I&T Environments
When there is spacecraft collaboration between several industry partners, there is an inherent difference in integration and test (I&T) methodologies, which creates a challenge for verifying flight systems during the development phase. To converge the differing I&T methodologies, considerations were required for multiple project areas such as Flight System Testbed (FST), Assembly, Test, and Launch Operations (ATLO), and Spacecraft Simulator environments. This paper details the challenges and approaches of the JPL's effort in engineering a solution to testing the flight system with the Mission Operations Ground System while maintaining the comparability with testing methods of the industry partners.
integration↗
Response to MRO's end-to-end data accountability challenges
(MRO) on August 12, 2005. It carries six science instruments and three engineering payloads. Because MRO will produce an unprecedented number of science products, it will transmit a much higher data volume via high data rate than any other deep space mission to date. Keeping track of MRO products as well as relay products would be a daunting, expensive task without a well-planned data-product tracking strategy. To respond to this challenge, the MRO project developed the End-to- End Data Accountability System by utilizing existing information available from both ground and flight elements. Therefore, a capability to perform first-order problem diagnosis is essential in order for MRO to answer the questions, where is my data? and when will my data be available? This paper details the approaches taken, design and implementation of the tools, procedures and teams that track data products from the time they are predicted until they arrive in the hands of the end users.
data delivery status tracking↗