Engineering topics

Lehmann, Michelle L.

Publications and source records attributed to Lehmann, Michelle L..

9 records

DOE OSTI2024

Enhanced Anhydrous Proton Conductivity in Azole Phosphonic Acid Mixtures

Azole molecules are investigated as potential candidates for proton conductors under anhydrous conditions. Since 1,2,3-triazole has the lowest melting point (T m = 17 °C), it was blended with three phosphonic acid-containing molecules (small molecules with one and two phosphonic acids per molecule and a phosphonic acid polymer) to provide a source of excess protons to enhance the proton conductivity of the blends. Here we study a wide range of compositions in each system to find that these three mixtures show a maximum proton conductivity at moderate doping compositions, approximately 5–10 azole molecules per phosphonic acid group. Using NMR diffusometry, we show that the protons bonded to nitrogen move faster than the protons bonded to carbons of 1,2,3-triazole, suggesting proton hopping between azole proton carriers. Given the high proton conductivity at 90 °C of the best mixtures, in the range of 20–60 mS/cm, this work provides a path forward for future work in anhydrous proton-conducting polymer membranes. Additionally, Raman spectroscopy was used to accurately determine the molar percentage of protonated 1,2,3-triazole. Combining that with the proton diffusion results, we find that the phosphonic acid polymer shows the most proton hopping at low acid content.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Composite Membrane for Sodium Polysulfide Hybrid Redox Flow Batteries

Non-aqueous redox flow batteries (NARFBs) using earth-abundant materials, such as sodium and sulfur, are promising long-duration energy storage technologies. NARFBs utilize organic solvents, which enable higher operating voltages and potentially higher energy densities compared with their aqueous counterparts. Despite exciting progress throughout the past decade, the lack of low-cost membranes with adequate ionic conductivity and selectivity remains as one of the major bottlenecks of NARFBs. Here, we developed a composite membrane composed of a thin (<25 µm) Na+-Nafion coating on a porous polypropylene scaffold. The composite membrane significantly improves the electrochemical stability of Na + -Nafion against sodium metal, exhibiting stable Na symmetric cell performance for over 2300 h, while Na + -Nafion shorted by 445 h. Additionally, the composite membrane demonstrates a higher room temperature storage modulus than the porous polypropylene scaffold and Na + -Nafion separately while maintaining high Na + conductivity (0.24 mS/cm at 20 °C). Our method shows that a composite membrane utilizing Na + -Nafion is a promising approach for sodium-based hybrid redox flow batteries.

25 ENERGY STORAGE↗

DOE OSTI2022

Nafion Inhibits Polysulfide Crossover in Hybrid Nonaqueous Redox Flow Batteries

Here, we report on the effectiveness of sodium-exchanged Nafion membranes for inhibiting polysulfide crossover during redox flow battery operation. The solubility of polysulfides allows them to be used as a high-capacity catholyte for nonaqueous redox flow batteries (NARFB). The NARFB cathode capacity is controlled by the total tank catholyte volume and polysulfide concentration and, as such, is independent of polysulfide adsorption sites on carbon fibers or nanotubes as found within traditional Na or Li–S batteries. However, one of the major barriers to the realization of polysulfide NARFBs is associated with developing a robust membrane that has minimal polysulfide crossover under the operating conditions. We found that sodium-exchanged Nafion membrane separators effectively inhibit polysulfide crossover within a Na–sulfur NARFB. These membranes significantly improve both capacity retention (70%) and Coulombic efficiencies (99%) after 50 cycles. Commercial porous membranes showed a large crossover as detected by UV–vis spectroscopy and resulted in low capacity retention (20%) and Coulombic efficiency (74%) after 45 cycles. Electrochemical impedance spectroscopy (EIS) measurements highlighted the trade-off between innate reactivity and ionic conduction of the membranes. The results show that dense, single ion conducting Nafion enables a long cycle life; however, it reacts with Na metal to form a resistive passivation layer and increases the cell resistance. On the contrary, the open pore structure of Celgard allows for higher current charge/discharge, and its chemical nature is compatible with Na; however, it has a high degree of polysulfide crossover.

25 ENERGY STORAGE↗

DOE OSTI2022

Unraveling Ion Transport in Trifluoromethanesulfonimide Pentablock Copolymer Membranes in Nonaqueous Electrolytes

Cation exchange membranes provide a key function in various nonaqueous energy storage technologies. As such, understanding the role of a nonaqueous liquid electrolyte on ion transport through a membrane is imperative. This study unravels relationships between membrane ion transport and electrolyte salt concentration utilizing a trifluoromethanesulfonimide-based pentablock copolymer membrane with polar and nonpolar nonaqueous electrolyte solutions. Here, the membrane plasticized with propylene carbonate (PC) exhibits a single-ion conductivity of 9.3 × 10 –6 S/cm at 25 °C. Tailoring the nonaqueous electrolyte and electrolyte salt concentration enables the single-ion conducting membrane to maintain a high cation transport number, >0.75, and boost ion conductivity more than 10 times to 1.3 × 10 –4 S/cm at 25 °C for the PC-based electrolyte solution. The findings provide critically important design parameters for energy storage systems utilizing nonaqueous electrolytes, such as Li- and Na-ion batteries and nonaqueous flow battery technologies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Membrane design for non-aqueous redox flow batteries: Current status and path forward

Redox flow batteries are promising technologies for large-scale, long-duration energy storage applications. Among them, non-aqueous redox flow batteries (NARFB) represent a transformative flow battery system since NARFBs potentially offer a higher energy density than aqueous flow batteries. However, many technical challenges remain for NARFBs, including the lack of high-performance membranes, low solubility of redox materials, and poor cycling efficiencies. Membranes serve a vital function in NARFBs, as they allow for selective ion transport while providing separation between the anolyte and catholyte. NARFB membrane development is an emerging research area, and this article reviews their design and critical factors that influence membrane properties, including solvent uptake, ion transport, and redox species permeability. A greater understanding of membrane behavior in non-aqueous solutions provides design principles for developing next-generation membranes for NARFB. In conclusion, we summarize the challenges, target metrics, and future perspectives for NARFBs.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2021

Separator Effect on Zinc Electrodeposition Behavior and Its Implication for Zinc Battery Lifetime

We report uncontrolled zinc electrodeposition is an obstacle to long-cycling zinc batteries. Much has been researched on regulating zinc electrodeposition, but rarely are the studies performed in the presence of a separator, as in practical cells. Here, we show that the microstructure of separators determines the electrodeposition behavior of zinc. Porous separators direct zinc to deposit into their pores and leave “dead zinc” upon stripping. In contrast, a nonporous separator prevents zinc penetration. Such a difference between the two types of separators is distinguished only if caution is taken to preserve the attachment of the separator to the zinc-deposited substrate during the entire electrodeposition–morphological observation process. Failure to adopt such a practice could lead to misinformed conclusions. Our work reveals the mere use of porous separators as a universal yet overlooked challenge for metal anode-based rechargeable batteries. Countermeasures to prevent direct exposure of the metal growth front to a porous structure are suggested.

25 ENERGY STORAGE↗

DOE OSTI2021

Additive manufacturing of strong silica sand structures enabled by polyethyleneimine binder

Abstract Binder Jet Additive Manufacturing (BJAM) is a versatile AM technique that can form parts from a variety of powdered materials including metals, ceramics, and polymers. BJAM utilizes inkjet printing to selectively bind these powder particles together to form complex geometries. Adoption of BJAM has been limited due to its inability to form strong green parts using conventional binders. We report the discovery of a versatile polyethyleneimine (PEI) binder for silica sand that doubled the flexural strength of parts to 6.28 MPa compared with that of the conventional binder, making it stronger than unreinforced concrete (~4.5 MPa) in flexural loading. Furthermore, we demonstrate that PEI in the printed parts can be reacted with ethyl cyanoacrylate through a secondary infiltration, resulting in an increase in flexural strength to 52.7 MPa. The strong printed parts coupled with the ability for sacrificial washout presents potential to revolutionize AM in various applications including construction and tooling.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Anomalously high elastic modulus of a poly(ethylene oxide)-based composite electrolyte

The practical use of lithium metal anodes in solid-state batteries requires a polymer membrane with high lithium-ion conductivity, thermal/electrochemical stability, and mechanical strength. The primary challenge is to effectively decouple the ionic conductivity and mechanical strength of the polymer electrolytes. We report a remarkably facile single step synthetic strategy based on in-situ crosslinking of poly(ethylene oxide) (xPEO) in the presence of a woven glass fiber (GF). Such a simple method yields composite polymer electrolytes (CPE) of anomalously high elastic modulus up to 2.5 GPa over a broad temperature range (20 °C – 245 °C) that has never been previously documented. An unsupervised machine learning algorithm, K-mean clustering analysis, was implemented on the hyperspectral Raman mapping at the xPEO/GF interface. Using such a unique means, we show for the first time that the promoted mechanical strength originates from xPEO and GF interactions through dynamic hydrogen and ionic bonding. High ionic conductivity is achieved by the addition plasticizer (e.g. tetraglyme), where trifluoromethanesulfonate anions are tethered to the xPEO matrix and Li + cations are favorably transported through coordination with the plasticizer. Further, stringent galvanostatic cycling tests indicates the CPE can be stably cycled for >3000 h in a Li-metal symmetric cell at a moderate temperature (nearly 1500 Coulombs/cm 2 Li equivalents), outperforming most of the PEO-based electrolytes. The GF reinforced CPE reported here has multifunctional uses, such as solid electrolytes for all solid-state batteries and membranes for redox-flow batteries. Although the focus of this study is on lithium-based batteries, the results are equally promising for other alkali metal based batteries such as sodium and potassium.

25 ENERGY STORAGE↗

DOE OSTI2020

Recent Developments and Challenges in Hybrid Solid Electrolytes for Lithium-Ion Batteries

Lithium-ion batteries (LIBs) have attracted worldwide research interest due to their high energy density and long cycle life. Solid-state LIBs improve the safety of conventional liquid-based LIBs by replacing the flammable organic electrolytes with a solid electrolyte. Among the various types of solid electrolytes, hybrid solid electrolytes (HSEs) demonstrate great promise to achieve high ionic conductivity, reduced interfacial resistance between the electrolyte and electrodes, mechanical robustness, and excellent processability due to the combined advantages of both polymer and inorganic electrolyte. This article summarizes recent developments in HSEs for LIBs. Approaches for the preparation of hybrid electrolytes and current understanding of ion-transport mechanisms are discussed. The main challenges including unsatisfactory ionic conductivity and perspectives of HSEs for LIBs are highlighted for future development. The present review provides insights into HSE development to allow a more efficient and target-oriented future endeavor on achieving high-performance solid-state LIBs.

25 ENERGY STORAGE↗