Search NASA⌕ Search

Engineering topics

Lemos, N. (ORCID:0000000267815672)

Publications and source records attributed to Lemos, N. (ORCID:0000000267815672).

8 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Resolving discrepancies in bang-time predictions for indirect-drive ICF experiments on the NIF: Insights from the Build-A-Hohlraum campaign

This study investigated discrepancies between measured and simulated x-ray drive in Indirect-Drive Inertial Confinement Fusion (ID-ICF) hohlraums at the National Ignition Facility. Despite advances in radiation-hydrodynamic simulations, a consistent “drive deficit” remains. Experimentally measured ID-ICF capsule bang-times are systematically 400–700 ps later than simulations predict. The Build-A-Hohlraum (BAH) campaign explored potential causes for this discrepancy by systematically varying hohlraum features, including laser entrance hole (LEH) windows, capsules, and gas fills. Overall, the agreement between simulated and experimental x-ray drive was found to be largely unaffected by these changes. The data allow us to exclude some hypotheses put forward to potentially explain the discrepancy. Errors in the local thermodynamic equilibrium (LTE) atomic modeling, errors in the modeling of LEH closure, and errors due to a lack of plasma species mix physics in simulations are shown to be inconsistent with our measurements. Instead, the data support the hypothesis that errors in NLTE emission modeling are a significant contributor to the discrepancy. X-ray emission in the 2–4 keV range is found to be approximately 30% lower than in simulations. This is accompanied by higher than predicted electron temperatures in the gold bubble region, pointing to errors in non-LTE modeling. Introducing an opacity multiplier of 0.87 on energy groups above 1.8 keV improves agreement with experimental data, reducing the bang-time discrepancy from 300 to 100 ps. These results underscore the need for refined NLTE opacity models to enhance the predictive power of hohlraum simulations.

Band emission↗
DOE OSTI2024

Diagnosing inertial confinement fusion ignition

Abstract Fusion ignition by inertial confinement requires compression and heating of the fusion fuel to temperatures in excess of 5 keV and densities exceeding hundreds of g/cc. In August 2021, this scientific milestone was surpassed at the National Ignition Facility (NIF), when the Lawson criterion for ignition was exceeded generating 1.37MJ of fusion energy (Abu-Shawareb et al 2022 Phys. Rev. Lett. 129 075001), and then in December 2022 target gain >1 was realized with the production of 3.1MJ of fusion energy from a target driven by 2.0MJ of laser energy (Abu-Shawareb et al 2024 Phys. Rev. Lett. 132 065102). At the NIF, inertial confinement fusion research primarily uses a laser indirect drive in which the fusion capsule is surrounded by a high-Z enclosure (‘hohlraum’) used to convert the directed laser energy into a symmetric x-ray drive on the capsule. Precise measurements of the plasma conditions, x-rays, γ -rays and neutrons produced are key to understanding the pathway to higher performance. This paper discusses the diagnostics and measurement techniques developed to understand these experiments, focusing on three main topics: (1) key diagnostic developments for achieving igniting plasmas, (2) novel signatures related to thermonuclear burn and (3) advances to diagnostic capabilities in the igniting regime with a perspective toward developments for intertial fusion energy.

Moore, A. S. (ORCID:0000000221258882)↗
DOE OSTI2024

Source size of x rays from self-modulated laser wakefield accelerators

A comparative study of x-ray sources generated with different mechanisms from self-modulated laser wakefield acceleration (SM-LWFA) electrons was performed to compare the source size or spatial resolution for use in high energy density science applications. We examine the source size of betatron, inverse Compton scattering, and bremsstrahlung radiation with a Fresnel diffraction based formalism and a modified x-ray ray tracing model. We observe the dependence of source size on the radiation generation process, laser parameters, and compare to what is possible in other regimes of LWFA, as well as current methods. This information is significant as we begin to explore the use of light sources driven by SM-LWFA for use as a diagnostic at large-scale laser facilities where blowout regime LWFA is not possible.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Measurement of early time outer laser beam reflection inside a cylindrical hohlraum at the National Ignition Facility

In a National Ignition Facility (NIF) cylindrical hohlraum, any specular reflection (“glint”) off the wall from the outer cone (incident angle of 50° and 44° relative to the surface of the wall) laser beam will irradiate the capsule poles. If the glint power is sufficiently large during the picket (early time) of the laser pulse, it may seed high-mode perturbations on the capsule surface that can grow during the implosion. To quantify the glint power on the capsule during the picket by the outer beams, we performed dedicated experiments on NIF using a flat witness foil as a surrogate for the capsule in a half-hohlraum target. We found that the measured glint power is approximately comparable to simulations using a nominal electron conduction flux limiter of f = 0.15, and over an order of magnitude lower than that predicted using f = 0.03 in the wall. Based on our current understanding, we conclude that the glint from the outer beams plays an insignificant role in capsule drive asymmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Modeling stimulated Brillouin backscatter from outer-cone quads across multiple inertial confinement fusion hohlraum designs

Stimulated Brillouin scattering (SBS) is a potential risk for laser damage in the experiments carried out at the National Ignition Facility (NIF), and by altering the energy deposition pattern in hohlraums, it affects the symmetry of indirect-drive inertial confinement fusion implosions. We have surveyed backward SBS on outer-cone quads across NIF integrated hohlraums of various platforms numerically, using three-dimensional (3D) simulations with the backscatter code pF3D [Berger et al. Phys. Plasmas 5, 4337 (1998)] and ray-based gain calculations. Simulated reflected powers and energies, as well as the spectrum of reflected light all compare favorably with measurements. Ray-based calculations of exponential SBS amplification (“gain”), which assume a strongly damped plasma wave and steady-state response, are performed using a novel method that includes the 3D speckled field of the laser that drives SBS. This approach is useful for understanding qualitative differences between hohlraum designs and identifying regions susceptible to SBS within hohlraums. Quantitatively, gains are not found to correlate with SBS reflectivities in 3D, necessitating fully wave-based calculations that naturally include diffraction and various temporal dependencies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Impact of flow-induced beam deflection on beam propagation in ignition scale hohlraums

Experiments examining the amount of specular reflection (or “glint”) within hohlraums containing different gas fill densities have recently been performed. Simulations of these experiments are presented that show using a single flux limiter cannot explain the decrease in glinted power with increasing gas fill density. The hypothesis that flow-induced beam deflection alters laser absorption is presented. A model is proposed that can be implemented into a ray tracing description of the laser commonly used in radiation hydrodynamic codes. It is shown that simulations using this model capture the trend with gas fill density improving agreement with measurements. This formulation is then applied to an ensemble of laser-driven inertial confinement fusion experiments performed at the National Ignition Facility. The proposed model shows little impact on the total x-ray drive on the capsule but a large impact on the resulting implosion symmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Parametric study of high-energy ring-shaped electron beams from a laser wakefield accelerator

Abstract Laser wakefield accelerators commonly produce on-axis, low-divergence, high-energy electron beams. However, a high charge, annular shaped beam can be trapped outside the bubble and accelerated to high energies. Here we present a parametric study on the production of low-energy-spread, ultra-relativistic electron ring beams in a two-stage gas cell. Ring-shaped beams with energies higher than 750 MeV are observed simultaneously with on axis, continuously injected electrons. Often multiple ring shaped beams with different energies are produced and parametric studies to control the generation and properties of these structures were conducted. Particle tracking and particle-in-cell simulations are used to determine properties of these beams and investigate how they are formed and trapped outside the bubble by the wake produced by on-axis injected electrons. These unusual femtosecond duration, high-charge, high-energy, ring electron beams may find use in beam driven plasma wakefield accelerators and radiation sources.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗