Engineering topics
Publications and source records attributed to Lessmann, G. G..
The formation of voids through interdiffusion in bimetallic welded structures exposed to high operating temperatures is inhibited by utilizing an alloy of the parent materials in the junction of the parent materials or by preannealing the junction at an ultrahigh temperature. These methods are also used to reduce the concentration gradient of a hardening agent.
HIP welding is effective method for fabricating complex structures or assemblies such as alternator rotors, regeneratively-cooled rocket-motor thrust chambers, and jet engine turbine blades. It can be applied to fabrication of many assemblies which require that component parts be welded together along complex interfaces.
Methods were developed for fabrication of a solid four pole alternator rotor by hot isostatic pressure welding. The rotor blanks welded in this program had complex geometrical mating interfaces and were of considerable bulk, being approximately 3-1/2 inches (0.089 meters) in diameter and 14 inches (0.356 meters) long. Magnetic end pieces were machined from AlSl 4340 steel, while the non-magnetic central section was of Inconel 718. Excellent welds were produced which were shown to be responsive to post weld heat treatments which substantially improved joint strength. Prior to welding the rotors, test specimens of complex geometry were welded to demonstrate that complex surfaces with intentional mechanical misfit could be readily joined using HIP welding. This preliminary work demonstrated not only that interface compliance is achieved during welding but that welding pressure is developed in these thick sections sufficient to produce sound joints. Integral weld-heat treatment cycles were developed that permitted the attainment of magnetic properties while minimizing residual stress associated with the allotropic transformation of 4340 steel.
The notched-tensile, tensile, and bend properties of GTA welds in T-111 and ASTAR-811C sheet were determined following a wide range of thermal exposures in order to define changes in ductility and mechanical property behavior due to weld aging response. No notch sensitivity or unusual tensile response was noted for any of the conditions evaluated. An aging response was noted for the bend ductile-brittle transition temperature determinations on both T-111 and ASTAR-811C welds. A tentative explanation for the observed response of each alloy is presented. In addition, the interrelationship of mechanical and chemical factors leading to underbead cracking in T-111 was investigated. The problem was shown to be amenable primarily to chemical solutions, such as alloy compositional changes. This was demonstrated by the improved performance of ASTAR-811C over T-111 in plate weld studies. Only modest success was achieved using procedural techniques as a means of eliminating underbead cracking.
Refractory metal alloys hot crack sensitivity testing by Varestraint method, using ultrahigh purity inert atmosphere
Post weld annealing for stabilizing tungsten alloy weld structure
The principles of the Varestraint test were applied to the evaluation of refractory metal alloys. This required development of a special test apparatus employing a modest specimen size for improved economy and compatible with the high purity inert atmosphere required for welding these alloys. Minimum specimen size is desirable because of the high cost of these alloys and also to permit timely testing of limited production developmental alloys. The Varestraint apparatus satisfies these requirements by providing a timely and economic test for hot crack sensitivity. This test can be used both for alloy development and production surveillance. The test apparatus was designed for use in vacuum purged dry boxes and is completely compatible with high purity inert atmosphere. Augmented strain can be varied continuously from 1/4% thru 4%. In addition to varying the augmented strain, the primary Varestraint variable, the effect on hot cracking of varying other weld parameters such as unit weld length heat input have also been studied. Test reproducibility, in terms of bending or strain rate, was demonstrated using high speed photography.
Long-time temperature stability of refractory metal alloys and weldability determinations
Weldability of tungsten base alloys and elevated temperature stability
Weldability and thermal stability of refractory metal alloys
Tungsten and tungsten base alloy weldability, discussing powder metallurgy, postweld annealing, high temperature tensile strength, etc
Design advantages of bimetallic construction enables an all-welded bimetallic joint to be made from the accessible header side of the tube-to-header joint. In the two-piece header design the weld joints completely seal the tube-header plate crevice and prevent crevice and stringer corrosion.
Refractory metal alloys rating on basis of weldability emphasizing metallurgical considerations, taking into account process control and welding as thermal process
Weldability and elevated temperature stability of refractory metal alloys
Effect of 1000 hour thermal exposures on tensile properties of refractory metal alloys
Inert atmosphere welding chamber, discussing measurement and control of contamination
Determination of weldability and elevated temperature stability of refractory metal alloys
Weldability and elevated temperature stability of refractory metal alloys