Search NASA⌕ Search

Engineering topics

Lester, H. C.

Publications and source records attributed to Lester, H. C..

36 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

The design and flight test of an engine inlet bulk acoustic liner

This paper summarizes the design, fabrication and flight evaluation of a Kevlar acoustic liner configuration for a JT15D turbofan engine. The liner was designed to suppress, by a measurable amount, a dominant (13,0) BPF tone. This tone or spinning mode was produced for research purposes by installing 41 circumferentially distributed small diameter rods upstream of the 28 fan blades. Duct liner attenuations calculated by a finite element procedure were compared to far field power (insertion) losses deduced from flight data. The finite element program modeled the variable geometry of the JT15D inlet and used a uniform flow with a boundary layer roll-off to model the inlet flow field. Calculated liner losses were generally conservative. That is, measured far field power losses were generally greater than attenuations calculated by the finite element computer program.

Lester, H. C.↗
NASA NTRS1981

Sound propagation through a variable area duct - Experiment and theory

A comparison of experiment and theory has been made for the propagation of sound through a variable area axisymmetric duct with zero mean flow. Measurement of the acoustic pressure field on both sides of the constricted test section was resolved on a modal basis for various spinning mode sources. Transmitted and reflected modal amplitudes and phase angles were compared with finite element computations. Good agreement between experiment and computation was obtained over a wide range of frequencies and modal transmission variations. The study suggests that modal transmission through a variable area duct is governed by the throat modal cut-off ratio.

Silcox, R. J.↗
NASA NTRS1980

Calculated and measured performance of a 'near ideal' locally reacting duct liner in grazing incidence

The calculated acoustic response of a nearly ideal (locally reacting and linear) duct liner has been compared with its measured performance. The ceramic honeycomb liner structure was such that the local reaction assumption was well satisfied over the frequency range of interest (0.5-3.0 kHz). In addition, the high repeatability of the measured impedance values over a large SPL range verified the assumption of linearity. A finite element algorithm was used to compute the duct liner transmission properties in terms of the liner's normal incidence impedance and the duct termination impedance using a plane wave source. Very good agreement between theory and experiment was observed in general, but required accurate normal impedance values in the high attenuation frequency bands of the liner's response.

Parrott, T. L.↗
NASA NTRS1979

Application of a finite element method for computing grazing incidence wave structure in an impedance tube - Comparison with experiment

The acoustic performance of a liner specimen, in a grazing incidence impedance tube, is analyzed using a finite element method. The liner specimen was designed to be a locally reacting, two-degree-of-freedom type with the resistance and reactance provided by perforated facesheets and compartmented cavities. Measured and calculated wave structures are compared for both normal and grazing incidence from 0.3 to 1.2 kHz. A finite element algorithm was incorporated into an optimization loop in order to predict liner grazing incidence impedance from measured SWR and null position data. Results suggest that extended reaction effects may have been responsible for differences between normal and grazing incidence impedance estimates.

Lester, H. C.↗
NASA NTRS1976

Optimal one-section and two-section circular sound-absorbing duct liners for plane-wave and monopole sources without flow

A discrete frequency study is made of the influence of source characteristics on the optimal properties of acoustically lined uniform and two section ducts. Two simplified sources, a plane wave and a monopole, are considered in some detail and over a greater frequency range than has been previously studied. Source and termination impedance effects are given limited examination. An example of a turbomachinery source and three associated source variants is also presented. Optimal liner designs based on modal theory approach the Cremer criterion at low frequencies and the geometric acoustics limit at high frequencies. Over an intermediate frequency range, optimal two section liners produced higher transmission losses than did the uniform configurations. Source distribution effects were found to have a significant effect on optimal liner design, but source and termination impedance effects appear to be relatively unimportant.

Lester, H. C.↗
NASA NTRS1975

Duct liner optimization for turbomachinery noise sources

An acoustical field theory for axisymmetric, multisectioned lined ducts with uniform flow profiles was combined with a numerical minimization algorithm to predict optimal liner configurations having one, two, and three sections. Source models studied include a point source located on the axis of the duct and rotor/outlet-stator viscous wake interaction effects for a typical research compressor operating at an axial flow Mach number of about 0.4. For this latter source, optimal liners for equipartition-of energy, zero-phase, and least-attenuated-mode source variations were also calculated and compared with exact results. It is found that the potential benefits of liner segmentation for the attenuation of turbomachinery noise is greater than would be predicted from point source results. Furthermore, effective liner design requires precise knowledge of the circumferential and radial modal distributions.

Lester, H. C.↗
NASA NTRS1974

Unified analysis of ducted turbomachinery noise

The methodologies of Hanson and Zorumski are combined to yield a unified analysis of ducted turbomachinery noise. It is shown that the far-field broad-band and discrete noise spectral components can be expressed in terms of modal cross-spectral matrices and directivity vectors which are derivable from the duct analysis.

Zorumski, W. E.↗
NASA NTRS1974

Unified analysis of ducted turbomachinery noise

An approach for an analysis of ducted turbomachinery noise is developed by combining features of the analysis of fan stator noise reported by Hanson (1973) with results obtained by Zorumski (1974). Hanson's analysis is briefly examined and a formula is derived for the far-field pressure due to a dipole pulse. Questions of transmission and reflection are discussed and attention is given to the radiation from ducted dipoles.

Zorumski, W. E.↗
NASA NTRS1974

An improved exceedance theory for combined random stresses

An extension is presented of Rice's classic solution for the exceedances of a constant level by a single random process to its counterpart for an n-dimensional vector process. An interaction boundary, analogous to the constant level considered by Rice for the one-dimensional case, is assumed in the form of a hypersurface. The theory for the numbers of boundary exceedances is developed by using a joint statistical approach which fully accounts for all cross-correlation effects. An exact expression is derived for the n-dimensional exceedance density function, which is valid for an arbitrary interaction boundary. For application to biaxial states of combined random stress, the general theory is reduced to the two-dimensional case. An elliptical stress interaction boundary is assumed and the exact expression for the density function is presented. The equations are expressed in a format which facilitates calculating the exceedances by numerically evaluating a line integral. The behavior of the density function for the two-dimensional case is briefly discussed.

Lester, H. C.↗
NASA NTRS1973

A finite element for thermal stress analysis of shells of revolution

A new finite element is described for performing detailed thermal stress analysis of thin orthotropic shells of revolution. The element provides for temperature loadings which may vary over the surface of the shell as well as through the thickness. In a number of sample calculations, results from the present method are compared with analytical solutions as well as with independent numerical analyses. Such calculations are carried out for two cylinders, a conical frustum, a truncated hemisphere, and an annular plate. Generally, the agreement between the present solution and the other solutions is excellent.

Adelman, H. M.↗
NASA NTRS1965

Scout vehicle flight loads.

Transverse flight loads produced on vertically rising Scout launch vehicle by horizontal winds and gusts

GUST LOAD↗