Search NASA⌕ Search

Engineering topics

Lewis, C. H.

Publications and source records attributed to Lewis, C. H..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Viscous shock-layer predictions of three-dimensional nonequilibrium flows past the space shuttle at high angle of attack

Computational solutions were obtained for chemically reacting flowfields over the entire windward surface of the Space Shuttle at high angle of attack. The recently developed computational method for the Space Shuttle is capable of treating three dimensional viscous nonequilibrium air flow as well as equilibrium air and perfect gas flows. A general nonorthogonal computational grid system is used to treat the nonaxisymmetric geometry. Boundary conditions take into account noncatalytic wall, equilibrium with noncatalytic wall condition are compared to the fully catalytic wall solutions, the equilibrium air solutions, the perfect gas solutions, and also the Shuttle flight heating and pressure data. The comparisons show good agreement and correlations in most cases.

Kim, M. D.↗
NASA NTRS1978

A procedure for calculating laminar, transitional and/or turbulent three-dimensional boundary layers including surface curvature effects about arbitrary blunt-nosed bodies

The governing equations for laminar, transitional and/or turbulent, incompressible, three-dimensional boundary layers are solved numerically. The equations are developed in terms of an orthogonal surface coordinate system and include surface curvature effects. The coordinates are generated numerically, while the inviscid flow is obtained from a general potential flow procedure. The only restrictions on body geometry are that it possess a blunt nose and a plane of symmetry. The boundary-layer equations, after being transformed into similarity type variables, are solved using the implicit finite-difference Krause scheme. Various test cases are presented to establish the accuracy of the resulting computer program.

Dwoyer, D. L.↗
NASA NTRS1975

Supersonic turbulent boundary-layer flows with mass injection through slots and/or porous walls

An implicit finite-difference method was used to solve the compressible boundary-layer equations, and to study the effects of mass transfer through porous plates, slots, and a combination of the two. The effects of the external pressure field were also included by using a global pressure interaction scheme. Two different eddy viscosity models were used for the slot and slot-porous combination cases: one was a two-layer model with inner and outer laws, and the other was a multi-layer model with as many as five separate layers. Results of the present method were compared with experimental data at a Mach number of 2.8. Comparisons of the skin friction reduction and Mach number profiles gave good to excellent agreement. Pressure interaction had little effect on the slot injection skin friction but increased the skin friction of the porous and slot-porous combination markedly.

Murray, A. L.↗
NASA NTRS1975

Hypersonic ionizing air viscous shock-layer flows over nonanalytic blunt bodies

The equations which govern the viscous shock-layer flow are presented and the method by which the equations are solved is discussed. The predictions of the present finite-difference method are compared with other numerical predictions as well as with experimental data. The principal emphasis is placed on predictions of the viscous flowfield for the windward plane of symmetry of the space shuttle orbiter and other axisymmetric bodies which approximate the shuttle orbiter geometry. Experimental data on two slender sphere-cones at hypersonic conditions are also considered. The present predictions agreed well with experimental data and with the past predictions. Substantial differences were found between present predictions and more approximate methods.

Miner, E. W.↗
NASA NTRS1975

Computer user's guide for a chemically reacting viscous shock-layer program

A description is given of the computer code for predicting viscous shock-layer flows over nonanalytic blunt bodies (Program VISLNABB) for hypersonic, low Reynolds number flows. Four specific and one general body geometries are considered. In addition to sphere-cones, cylinder wedges and geometries defined in tabular form, options for hyperboloids and paraboloids are included. Details of the theory and results are included in a separate engineering report. The program, subroutines, variables in common, and input and output data are described. Listings of the program code, output data for a sample case, and the input data for this sample case are included.

Miner, E. W.↗
NASA NTRS1974

Viscous shock-layer flows for the space shuttle windward plane of symmetry

Predictions are presented for hypersonic, nonequilibrium viscous flows over nonanalytic blunt bodies at reentry conditions. Emphasis is placed on predictions of the viscous flowfield for the windward plane of symmetry of the space shuttle and other axisymmetric bodies which approximate the space shuttle geometry. The equations which govern the viscous shock-layer flow are presented, and the method by which the equations are solved is discussed. The predictions of the present finite-difference method are compared with predictions of other numerical methods as well as with experimental data.

Miner, E. W.↗
NASA NTRS1974

Rearward-facing steps in laminar supersonic flows with and without suction

An experimental investigation of heat-transfer and pressure distributions within regions of laminar separated flows produced by two-dimensional rearward-facing steps has been carried out at freestream Mach numbers of around 4 in the range of step height-to-boundary layer thickness varying from 0.1 to 2.4. With no suction from the separated area, the ratio of the maximum post-step heat transfer to the attached-flow values was less than unity. The maximum heating-rate region was located far downstream of the reattachment plate stagnation point. Mass suction from the separated area increased the local heating rates, this effect was however relatively weak for purely laminar flow conditions and the competing effect of the step height clearly predominated. At step heights comparable with boundary-layer thickness, even removing the entire approaching boundary layer was not sufficient to raise the post-step heating rates above the flat-plate values.

Jakubowski, A. K.↗
NASA NTRS1974

Hypersonic chemically reacting viscous shock layers over sphere-cones and cylinder-wedges

Hypersonic, nonequilibrium viscous flow over nonanalytic blunt bodies is considered. The equations which govern the viscous shock-layer flow are presented and the method by which the equations are solved is discussed. The predictions of the present finite-difference method are compared with other numerical predictions as well as with experimental data. Three flow conditions are considered; the experimental, wind tunnel conditions of Pappas and Lee for a 7.5 deg sphere-cone at Mach 13 and two cases considered by Kang and Dunn, a 9 deg sphere-cone at 233,000 ft and a 20 deg sphere-cone at 280 and 310 Kft. The predictions of the present method agreed well with the experimental heat-transfer data, but substantial differences were found between the present predictions and the more approximate predictions of Kang and Dunn for heat-transfer distributions and temperature profiles.

Miner, E. W.↗
NASA NTRS1973

Experimental study of supersonic laminar base flow with and without suction

Heat-transfer and pressure distributions in laminar separated flows downstream of rearward-facing steps with and without mass suction were investigated at Mach numbers around 4 for the conditions when the boundary-layer thickness was comparable to or larger than the step height. In both suction and no-suction cases, an increase of the step height resulted in a sharp drop of the base heating rates, which then gradually recovered to less than or near attached-flow values obtained with flat-plate configuration. Mass suction from the step base area increased the local heating rates; this effect, however, was relatively weak for laminar flows tested, and the competing effect of the step height clearly predominated. It was found that even removal of the entire incoming boundary layer was not sufficient to raise the poststep heating rates above the flat-plate values. The base pressure in the no-suction, solid-step case correlated reasonably well with the step height-to-boundary-layer thickness ratio and with the Reynolds number based on the step height.

Jakubowski, A. K.↗
NASA NTRS1973

Rearward-facing steps in laminar supersonic flows with and without suction.

It was found in the experimental study conducted that, for both suction and no-suction cases, an increase in the step height caused a sharp drop in the initial heating rates which then gradually recovered to less or near the attached-flow values. The height of the step controlled the heating rates at the step base. Mass suction from the separated area increased the local heating rates, the relative increase being most significant immediately behind the step. In general, however, the effect of mass suction on heat-transfer at all laminar flows was relatively weak.

Jakubowski, A. K.↗
NASA NTRS1973

Supersonic turbulent boundary-layer flows with tangential slot injection.

An implicit finite-difference method has been developed for the solution of the compressible boundary-layer equations. This method is applied to tangential slot injection into supersonic turbulent boundary-layer flows. In addition, the effects induced by the interaction between the boundary-layer displacement thickness and the external pressure field are considered. Three different eddy viscosity models have been used to specify the turbulent momentum exchange. One model depends on the species concentration profile, and the species conservation equation has been included in the system of governing partial differential equations. For air injected into air, the freestream and injected gases are treated as separate species which have common fluid properties. Calculations were made and results were compared with experimental data at freestream Mach numbers of 2.4 and 6.0 and with results of another finite-difference method. Good agreement was obtained for the reduction of wall skin friction with slot injection.

Miner, E. W.↗
NASA NTRS1973

Non-reacting and equilibrium chemically reacting turbulent boundary-layer flows.

Turbulent boundary-layer flows of nonreacting gases are predicted for both internal (nozzle) and external flows. Effects of favorable pressure gradients on two eddy viscosity models were studied in rocket and hypervelocity wind tunnel flows. Nozzle flows of equilibrium air with stagnation temperatures up to 10,000 K were computed. Predictions of equilibrium nitrogen flows through hypervelocity nozzles were compared with experimental data. A slender spherically blunted cone was studied at 70,000 ft altitude and 19,000 ft/sec in the earth's atmosphere. Comparisons with available experimental data showed good agreement. A computer program was developed and fully documented during this investigation for use by interested individuals.

Anderson, E. C.↗
NASA NTRS1972

A finite difference method for predicting supersonic turbulent boundary layer flows with tangential slot injection

An implicit finite difference method has been applied to tangential slot injection into supersonic turbulent boundary layer flows. In addition, the effects induced by the interaction between the boundary layer displacement thickness and the external pressure field are considered. In the present method, three different eddy viscosity models have been used to specify the turbulent momentum exchange. One model depends on the species concentration profile and the species conservation equation has been included in the system of governing partial differential equations. Results are compared with experimental data at stream Mach numbers of 2.4 and 6.0 and with results of another finite difference method. Good agreement was generally obtained for the reduction of wall skin friction with slot injection and with experimental Mach number and pitot pressure profiles. Calculations with the effects of pressure interaction included showed these effects to be smaller than effects of changing eddy viscosity models.

Miner, E. W.↗
NASA NTRS1971

Laminar or turbulent boundary-layer flows of perfect gases or reacting gas mixtures in chemical equilibrium

Turbulent boundary layer flows of non-reacting gases are predicted for both interal (nozzle) and external flows. Effects of favorable pressure gradients on two eddy viscosity models were studied in rocket and hypervelocity wind tunnel flows. Nozzle flows of equilibrium air with stagnation temperatures up to 10,000 K were computed. Predictions of equilibrium nitrogen flows through hypervelocity nozzles were compared with experimental data. A slender spherically blunted cone was studied at 70,000 ft altitude and 19,000 ft/sec. in the earth's atmosphere. Comparisons with available experimental data showed good agreement. A computer program was developed and fully documented during this investigation for use by interested individuals.

Anderson, E. C.↗
NASA NTRS1971

A computer program for two-dimensional and axisymmetric nonreacting perfect gas and equilibrium chemically reacting laminar, transitional and-or turbulent boundary layer flows

A computer program is described in detail for laminar, transitional, and/or turbulent boundary-layer flows of non-reacting (perfect gas) and reacting gas mixtures in chemical equilibrium. An implicit finite difference scheme was developed for both two dimensional and axisymmetric flows over bodies, and in rocket nozzles and hypervelocity wind tunnel nozzles. The program, program subroutines, variables, and input and output data are described. Also included is the output from a sample calculation of fully developed turbulent, perfect gas flow over a flat plate. Input data coding forms and a FORTRAN source listing of the program are included. A method is discussed for obtaining thermodynamic and transport property data which are required to perform boundary-layer calculations for reacting gases in chemical equilibrium.

Miner, E. W.↗